2000 GMC Sierra 3500
TSBs (Technical Service Bulletins)
Technical Service Bulletins (TSBs) for the 2000 Sierra 3500 are official communications between GMC & their dealerships that describe processes for troubleshooting or fixing certain common problems. All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
-
TSB #060309004N
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact. Read More »
-
TSB #23-NA-144
This technical bulletin provides information and a solution to a condition of Brake Pedal Moves or Self Applies at Full Turns. Read More »
-
TSB #PIT3665L
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
-
TSB #PIT3665H
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
-
TSB #130522001B
Pre-Formed and Pre-Flared Hydraulic Brake Pipe Kits Now Available for Service Read More »
-
TSB #PI1394A
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE. Read More »
-
TSB #000601012F
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES. Read More »
-
TSB #16-NA-383
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
-
TSB #22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
-
TSB #PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine. Read More »
-
TSB #23-NA-153
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
-
TSB #18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
-
TSB #03-06-01-023G
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil. Read More »
-
TSB #22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters. Read More »
-
TSB #21-NA-124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
-
TSB #22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
-
TSB #22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters. Read More »
-
TSB #03-06-01-023F
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil. Read More »
-
TSB #20-NA-065
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set. Read More »
-
TSB #22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters. Read More »
-
TSB #03-06-01-023E
This information bulletin explains how to measure for oil consumption and possible reasons for loss of oil. Read More »
-
TSB #22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
-
TSB #22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters. Read More »
-
TSB #PIP5628E
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
-
TSB #PIP5540D
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
-
TSB #PI1394
This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons. Read More »
-
TSB #PIP5226
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Read More »
-
TSB #PIP5163A
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
-
TSB #PIP5163
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or ... Read More »
-
TSB #PIT3173C
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Read More »
-
TSB #04292004
ENGINE MAY HAVE A CONDITION IN WHICH THE EXHAUST VALVE STEM MAY BECOME DEFORMED. THIS INCLUDES 1999-01 CHEVROLET AND GMC 4500 AND 5500 MODELS. *EH Read More »
-
TSB #PIP-4695
GM: LOSS OF POWER HESITATES ON ACCELERATION. 4.3, 4.8, 5.3, 5.7 AND 6.0 ENGINES COUPLED WITH THE 4L60E OR 4L65E MAY EXPERIENCE A CONDITION OF HESITATES, MISSES OR LOSS OF POWER UNDER ACCELERATION. Read More »
-
TSB #22NA009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters. Read More »
-
TSB #PIP5628F
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
-
TSB #PIP4925B
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools. Read More »
-
TSB #PIP5232B
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. Read More »
-
TSB #010604037B
INFORMATION REGARDING FUEL TRANSFER PUMP INOPERATIVE. *YH Read More »
-
TSB #010604037
TECHNICAL SERVICE BULLETIN REGARDING FUEL TRANSFER PUMP INOPERATIVE. *TT Read More »
-
TSB #04-06-04-051F
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive. Read More »
-
TSB #16NA383
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
-
TSB #01349A
6.5L L49 L56 L57 L65 DIESEL ENGINE REQUIRING FUEL INJECTION PUMP REPLACEMENT. MODELS P32/P42 1994-1999 INCLUDED. *TT Read More »
-
TSB #PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine. Read More »
-
TSB #23-NA-153
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
-
TSB #22-NA-181
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission. Read More »
-
TSB #010417001B
SUBJECT REGARDING LAUNCH SHUDDER ON ACCELERATION (INSTALL NEW ONE-PIECE PROPELLER SHAFT) *JG Read More »
-
TSB #010730021
THIS TECHNICAL SERVICE BULLETIN STATES THAT TECHNICIANS MAY EXPERIENCE DIFFICULTY IN REMOVING THE CONNECTORS FROM THE PARK / NEUTRAL POSITION SWITCH, USUALLY WHEN TRYING TO REMOVE THE SWITCH DURING TRANSMISSION SERVICE. Read More »
-
TSB #010730020
SUBJECT ORDERING REFERENCE TABLE FOR ORDERING THE NEW VALVE BODY, SPACER PLATE AND GASKET KIT. *TT Read More »
-
TSB #010417001A
SOME CUSTOMERS MAY COMMENT ON A VIBRATION DURING ACCELERATION FROM 0 - 40 KM/H (0 - 25 MPH). *TT Read More »
-
TSB #PIP3720D
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Read More »
-
TSB #010417001
SOME EXTENDED AND CREW CAB LONG BOX PICKUP MODELS INCLUDING 1999 AND 2001 CHEVROLET K2500 MODELS WITH AUTOMATIC TRANSMISSION MAY EXHIBIT A VIBRATION (LAUNCH SHUDDER) DURING ACCELERATION FROM 0-40 KM/H (0-25). Read More »
-
TSB #23-NA-001
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information. Read More »
-
TSB #22-NA-205
This service bulletin provides information on Module Harvesting. Read More »
-
TSB #PIT5485B
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
-
TSB #PIC-5050-A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. Read More »
-
TSB #PIC-4935-E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. Read More »
-
TSB #PIC4935E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. Read More »
-
TSB #PIT5485A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
-
TSB #15-NA-079
OnStar? Voice Fallback Number Update Some customers may have received a letter from OnStar? stating that "We recently tried to provide a software update to the OnStar? hardware in your vehicle. Read More »
-
TSB #PIP5094
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection ... Read More »
-
TSB #PIC3718E
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Read More »
-
TSB #PIC4935D
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the ... Read More »
-
TSB #PIC-4935-E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. Read More »
-
TSB #PIC3100F
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Read More »
-
TSB #15-08-44-001I
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade. Read More »
-
TSB #01-08-42-001O
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
-
TSB #PIT3237F
This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet protection or tint offered by the windshield or side glass. Read More »
-
TSB #PIT3237F
This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet protection or tint offered by the windshield or side glass. Read More »
-
TSB #PIT5099G
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
-
TSB #PIT5099F
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
-
TSB #PI0281D
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Read More »
-
TSB #PI0281D
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Read More »
-
TSB #PIT3227P
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Read More »
-
TSB #17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
-
TSB #17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
-
TSB #99-08-51-007F
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
-
TSB #99-08-51-007F
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
-
TSB #SB-10-08-50-003B
GENERAL MOTORS: INFORMATION PROVIDED BY BULLETIN FOR ALL 2012 AND PRIOR GENERAL MOTOR TRUCKS AND PASSENGER VEHICLES REGARDING THE ADJUSTABLE COMFORT AND CUSTOM UPHOLSTERY OF THE DRIVER AND THE PASSENGER HEAD RESTRAINT. Read More »
-
TSB #15-NA-079
OnStar Voice Fallback Number Update Read More »
-
TSB #23-NA-219
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories. Read More »
-
TSB #23-NA-001
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information. Read More »
-
TSB #PIT3099U
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
-
TSB #100089006H
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only). Read More »
-
TSB #16NA383
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
-
TSB #15-NA-079
OnStar? Voice Fallback Number Update Some customers may have received a letter from OnStar? stating that "We recently tried to provide a software update to the OnStar? hardware in your vehicle. Read More »
-
TSB #PIC5588B
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. Read More »
-
TSB #99-08-51-007F
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
-
TSB #99-08-51-007F
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
-
TSB #PIC5050A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. Read More »
-
TSB #15-NA-079
OnStar Voice Fallback Number Update Read More »
-
TSB #PIT5399
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Read More »
-
TSB #PIC4310J
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
-
TSB #PIC5588B
Programming And Activation Of Replacement OnStar Modules. Read More »
-
TSB #PIC5588A
Programming And Activation Of Replacement OnStar Modules. Read More »
-
TSB #PIC5959B
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Read More »
-
TSB #PIT5485B
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
-
TSB #PIT5389A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS. Read More »
-
TSB #PIT5485A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE. Read More »
-
TSB #PIC4310J
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Read More »
-
TSB #PIC5588B
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. Read More »
-
TSB #04-06-04-051F
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive. Read More »
-
TSB #18-NA-099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
-
TSB #PIP5601B
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
-
TSB #23-NA-219
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories. Read More »
-
TSB #PIP5358C
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
-
TSB #04-00-89-015Z
This bulletin provides information on Warranty Administration a?? Required Operating Procedures - 8 Points (U.S. Only). Read More »
-
TSB #17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy. Read More »
-
TSB #22-NA-195
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada. Read More »
-
TSB #100089006G
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only). Read More »
-
TSB #17-NA-073
This warranty administration bulletin provides policy information with the field action courtesy transportation policy. Read More »
-
TSB #PIT5264B
Canadian Customers Unable To Place Calls And Turn By Turn Inoperative In The United States. Read More »
-
TSB #Recalls
Vehicle Recalls Read More »
-
TSB #PIT5264
Canadian Customers Unable To Place Calls In The United States Read More »
-
TSB #16NA383
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
-
TSB #PIT3099M
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Read More »
-
TSB #99-08-51-007F
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
-
TSB #99-08-51-007F
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Read More »
-
TSB #PI0281D
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Read More »
-
TSB #PI0281D
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Read More »
-
TSB #PIT3099J
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Read More »
-
TSB #609
A/C LOW PRESSURE SWITCH DIAGNOSIS. *SC Read More »
-
TSB #010856004
INFORMATION REGARDING SECURITY LAMP ILLUMINATING ON THE INSTRUMENT PANEL, ENGINE STALL, NO START, AND DIAGNOSIC TROUBLE CODE B2960. *SLC Read More »
-
TSB #010730002B
MALFUNCTION INDICATOR LAMP (MIL) IS ON; THE TRANSMISSION IS STUCK IN THIRD GEAR; AND / OR THE INSTRUMENT CLUSTER IS INOPERATIVE. *TT Read More »