2019 GMC Sierra 3500
TSBs (Technical Service Bulletins)
Technical Service Bulletins (TSBs) for the 2019 Sierra 3500 are official communications between GMC & their dealerships that describe processes for troubleshooting or fixing certain common problems. All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
-
TSB #03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
-
TSB #15-00-89-004F
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
-
TSB #PI0281J
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
-
TSB #13-02-32-001G
This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures. Read More »
-
TSB #PIT5544F
This Preliminary information communicates information on a hydrauilc rush type noise from the power steering gear. This noise is a characteristic of the new Active Hydraulic Assist System RPO NV8 and no repairs should be made. Read More »
-
TSB #15-00-89-004E
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
-
TSB #16-NA-109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
-
TSB #PIT5544E
This Preliminary information communicates information on a hydrauilc rush type noise from the power steering gear. This noise is a characteristic of the new Active Hydraulic Assist System RPO NV8 and no repairs should be made. Read More »
-
TSB #20NA006
This informational bulletin explains there is another steering hose that can be used for cold weather drivers that experience a steering hose leak. Read More »
-
TSB #20NA021
This technical bulletin provides repair information to correct a customer concern of Intermittent "Service Steering Column Lock" message displayed with U0155 Set. Read More »
-
TSB #20NA006
This informational bulletin explains there is another steering hose that can be used for cold weather drivers that experience a steering hose leak. Read More »
-
TSB #PIT5288G
This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information ... Read More »
-
TSB #130232001F
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures. Read More »
-
TSB #PIT5527B
This Preliminary Information communication provides information to the technician about vehicles that show a "Take Steering" message on the Driver Information Center along with a warning chime/alert. Read More »
-
TSB #17NA330
This informational bulletin provides information for the customer to pair their phone in order for the push to talk button on the steering wheel control to work. Read More »
-
TSB #03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
-
TSB #15-00-89-004F
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
-
TSB #PI0281J
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
-
TSB #21-NA-138
This service bulletin provides a repair procedure to correct a customer concern of a Squeak, Grind or Clunking Noise from Rear Leaf Springs. Read More »
-
TSB #21-NA-138
This service bulletin provides a repair procedure to correct a customer concern of a Squeak, Grind or Clunking Noise from Rear Leaf Springs. Read More »
-
TSB #15-00-89-004E
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
-
TSB #PIT5457D
This Preliminary Information communication provides information to the technician about vehicle with Service ABS and/or Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of ... Read More »
-
TSB #060309004N
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact. Read More »
-
TSB #060309004M
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact. Read More »
-
TSB #PIT5479F
This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. Read More »
-
TSB #23-NA-144
This technical bulletin provides information and a solution to a condition of Brake Pedal Moves or Self Applies at Full Turns. Read More »
-
TSB #PIT3665L
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
-
TSB #21-NA-043
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
-
TSB #20NA161
This informational bulletin advises the technician to check for a possible stuck oil pressure relief valve. Read More »
-
TSB #PIT5206G
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? ... Read More »
-
TSB #PIT3665H
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. Read More »
-
TSB #PIT5311E
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver ... Read More »
-
TSB #PIT5479B
This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. Read More »
-
TSB #15-00-89-004E
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
-
TSB #PIT5569B
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC. Read More »
-
TSB #PIT5662F
This Preliminary information communicates information to diagnose DTC C056D or C056E. Read More »
-
TSB #19NA035
This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as intended, causing the parking pawl to engage while driving. Read More »
-
TSB #19NA035
This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as intended, causing the parking pawl to engage while driving. Read More »
-
TSB #20-NA-207
This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set. Read More »
-
TSB #16-NA-372
This bulletin provides information on common diesel engine tick noises and how they are considered part of normal operation and no parts should be replaced for these normal operating conditions. Read More »
-
TSB #12-00-89-003B
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
-
TSB #PIP5844
This Preliminary information communicates the possibility of dtc p06DD due to low or no oil pressure immediately following engine oil and filter change due to oil filter and main oil gallery being drained or empty. Read More »
-
TSB #22NA014
This technical provides a procedure to check for a possible faulty Reductant Injector and replace if the cause of the customers concern. Read More »
-
TSB #18NA073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
-
TSB #PIP5632F
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
-
TSB #PIP5794B
This Preliminary information communicates diagnostics to the dealer involving a vehicle shudder concern caused by the camshaft actuator system that can be mistaken for a transmission issue. Read More »
-
TSB #19NA187
This bulletin provides additional information on how to graph a cylinder misfire and a possible diagnostic cause. Read More »
-
TSB #20NA176
This technical bulletin provides a procedure to update the GPCM if found the cause of the customers concern. Read More »
-
TSB #PIP5684B
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
-
TSB #PIP5504F
This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Read More »
-
TSB #PIP5733
This Preliminary information communicates Possible Crank no start or extended crank with DTC p12A6 set current or history. Under Investigation Read More »
-
TSB #20NA043
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
-
TSB #18NA073
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
-
TSB #19NA212
This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away to correct a crank/No Start condition. Read More »
-
TSB #PIP5531A
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with ... Read More »
-
TSB #N192264210 Messa
Customer Satisfaction Program. Stock VIN List sent. Read More »
-
TSB #PIP5630B
This Preliminary information communicates A vehicle may have a concern of no oil pressure and/or P0521 set. the releif valve in the pump is sticking or the number 1 main bearing is damaged. Drop oil pan and confirm #1 main is spun or not. Read More »
-
TSB #090604026Q
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2. Read More »
-
TSB #19NA109
This informational bulletin provides information for dealers/technicians on Oil Life Monitor Engine Control Module Update. Read More »
-
TSB #PIP5629
This Preliminary information communicates to the dealer technicians that the oil life monitoring system for 2019 Duramax 6.6 L5P is under investigation by engineering. Read More »
-
TSB #PIT5391E
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be ... Read More »
-
TSB #17NA051
This informational bulletin provides information on High Oil Pressure during Initial Start of Vehicle is considered a normal characteristic and no repairs should be completed for this condition. Read More »
-
TSB #18366
Service Update. Certain vehicles that are equipped with a Duramax diesel engine, the engine control module (ECM) may not take the appropriate remedial actions if an exhaust gas temperature sensor becomes disconnected. Read More »
-
TSB #PIT5350B
This Preliminary Information communication advises the technician that there have been some reports that the current engine hours are not correct and display 0.0. Read More »
-
TSB #18NA334
This informational bulletin provides information on characteristics of the new engine versus the old engine. Read More »
-
TSB #23-NA-032
The informational bulletin advises the tech to use the glow plug bore cleaner to reduce the chance of soot building up on the glow plug causing a premature failure. Read More »
-
TSB #16-NA-383
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels ... Read More »
-
TSB #22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
-
TSB #16-NA-222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
-
TSB #16-NA-338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
-
TSB #PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine. Read More »
-
TSB #20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements. Read More »
-
TSB #21-NA-135
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
-
TSB #03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
-
TSB #21-NA-228
This bulletin provides a procedure to program the BCM to correct the customers concern of RKE idle Time-out. Read More »
-
TSB #21-NA-228
This bulletin provides a procedure to program the BCM to correct the customers concern of RKE idle Time-out. Read More »
-
TSB #01-06-01-011O
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption. Read More »
-
TSB #17-NA-157
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter. Read More »
-
TSB #23-NA-153
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
-
TSB #18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
-
TSB #16-NA-222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
-
TSB #23-NA-141
This informational bulletin advised the technician that the engine and related parts will be debited if found that the tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged ... Read More »
-
TSB #15-00-89-004F
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
-
TSB #04-06-04-051H
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive. Read More »
-
TSB #16-NA-244
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system. Read More »
-
TSB #03-06-01-023G
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil. Read More »
-
TSB #09-06-04-026X
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2. Read More »
-
TSB #23-NA-027
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
-
TSB #01-06-01-011N
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption. Read More »
-
TSB #17-NA-374
This informational bulletin advises the technician of how the Soot information has changed from grams to percentage. Read More »
-
TSB #04-07-30-013E
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
-
TSB #19-NA-219
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue. Read More »
-
TSB #19-NA-237
This service bulletin explains how to identify possible DEF system contamination. Read More »
-
TSB #PI0281J
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
-
TSB #20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements. Read More »
-
TSB #23-NA-027
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
-
TSB #19-NA-219
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue. Read More »
-
TSB #21-NA-043
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
-
TSB #00-06-01-012M
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
-
TSB #00-06-01-026Q
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
-
TSB #16-NA-222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
-
TSB #22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters. Read More »
-
TSB #18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
-
TSB #19-NA-237
This service bulletin explains how to identify possible DEF system contamination. Read More »
-
TSB #16-NA-244
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system. Read More »
-
TSB #16-NA-372
This bulletin provides information on common diesel engine tick noises and how they are considered part of normal operation and no parts should be replaced for these normal operating conditions. Read More »
-
TSB #07-06-01-016I
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement. Read More »
-
TSB #16-NA-380
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
-
TSB #10-06-05-002L
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
-
TSB #16-NA-376
This informational bulletin provides information on higher than expected oil consumption. Read More »
-
TSB #18-NA-361
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
-
TSB #23-NA-032
The informational bulletin advises the tech to use the glow plug bore cleaner to reduce the chance of soot building up on the glow plug causing a premature failure. Read More »
-
TSB #20-NA-203
This informational bulletin explains how the regen works for the DEF system and how it works at different levels. Read More »
-
TSB #21-NA-228
This bulletin provides a procedure to program the BCM to correct the customers concern of RKE idle Time-out. Read More »
-
TSB #18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
-
TSB #21-NA-124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set. Read More »
-
TSB #16-NA-338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
-
TSB #20-NA-138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
-
TSB #22-NA-216
This bulletin advises the technician to Inspect the position of the head gasket locating tabs to determine if the head gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running ... Read More »
-
TSB #22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
-
TSB #18-NA-361
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
-
TSB #22-NA-216
This bulletin advises the technician to Inspect the position of the head gasket locating tabs to determine if the head gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running ... Read More »
-
TSB #PIP5175E
This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th ... Read More »
-
TSB #03-06-04-017R
This service bulletin provides information on availability of Diesel Fuel additives. Read More »
-
TSB #05-06-04-022T
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
-
TSB #15-00-89-004E
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
-
TSB #06-00-89-031H
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification. Read More »
-
TSB #07-06-01-016H
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement. Read More »
-
TSB #09-06-04-026W
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2. Read More »
-
TSB #16-NA-244
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system. Read More »
-
TSB #16-NA-380
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
-
TSB #18-NA-103
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
-
TSB #05-00-89-072F
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management. Read More »
-
TSB #22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters. Read More »
-
TSB #20-NA-203
This informational bulletin explains how the regen works for the DEF system and how it works at different levels. Read More »
-
TSB #01-06-01-011M
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption. Read More »
-
TSB #00-06-01-012L
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
-
TSB #04-06-04-051G
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive. Read More »
-
TSB #10-06-05-002K
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
-
TSB #19-NA-237
This informational bulletin explains how to identify possible DEF contamination. Read More »
-
TSB #00-06-01-026P
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage. Read More »
-
TSB #16-NA-222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
-
TSB #17-NA-374
This informational bulletin advises the technician of how the Soot information has changed from grams to percentage. Read More »
-
TSB #18-NA-011
Informational bulletin explaining how a plow may cause overheating and engine damage when traveling over 45 mph. Read More »
-
TSB #21-NA-113
This technical bulletin provides a procedure to perform a learn procedure for the turbo actuator. Read More »
-
TSB #18-NA-098
This informational bulletin provides information for the technicians on where to look on the Duramax engine for coolant leaks. Read More »
-
TSB #18-NA-150
This informational bulletin provides information on 6.6L Duramax Possible Oil Leak Path Information. Read More »
-
TSB #19-NA-187
This bulletin provides additional information on how to graph a cylinder misfire and a possible diagnostic cause. Read More »
-
TSB #16-NA-376
This informational bulletin provides information on higher than expected oil consumption. Read More »
-
TSB #16-NA-372
This bulletin provides information on common diesel engine tick noises and how they are considered part of normal operation and no parts should be replaced for these normal operating conditions. Read More »
-
TSB #03-06-01-023F
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil. Read More »
-
TSB #20-NA-065
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set. Read More »
-
TSB #19-NA-044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
-
TSB #12-01-37-001F
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service. Read More »
-
TSB #22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters. Read More »
-
TSB #21-NA-043
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
-
TSB #14-06-04-004H
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours. Read More »
-
TSB #03-06-01-023E
This information bulletin explains how to measure for oil consumption and possible reasons for loss of oil. Read More »
-
TSB #22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system. Read More »
-
TSB #15-06-01-002L
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated. Read More »
-
TSB #22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters. Read More »
-
TSB #PIP5844
This Preliminary information communicates the possibility of dtc p06DD due to low or no oil pressure immediately following engine oil and filter change due to oil filter and main oil gallery being drained or empty. Read More »
-
TSB #PIT5479E
This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. Read More »
-
TSB #19NA187
This bulletin provides additional information on how to graph a cylinder misfire and a possible diagnostic cause. Read More »
-
TSB #N212346580
Block Heater Restore Read More »
-
TSB #PIP5832
This Preliminary information communicates to the dealer an issue where a vehicle may be exhibiting an engine noise condiion. The dealer is instructed on how to isolate the noise to a specific area of the engine for further diagnosis. Read More »
-
TSB #PIP5628E
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
-
TSB #19NA153
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM for metal. Read More »
-
TSB #19NA104
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
-
TSB #PIT5245D
This Preliminary Information communication provides information to the technician about vehicles that the blower motor may be noisy or vibrate when running. Read More »
-
TSB #18NA098
This informational bulletin provides information for the technicians on where to look on the Duramax engine for coolant leaks. Read More »
-
TSB #20NA043
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
-
TSB #PIP5719B
This Preliminary information communicates the possibility of dtc P12A6 with the possibility of a crank no start or extended crank concern. Read More »
-
TSB #N192264210
N192264210 - Customer Satisfaction Program - Certain vehicles may have a condition in which the block heater cable function was disabled. Dealers will replace the engine block heater and cord. Read More »
-
TSB #18NA361
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
-
TSB #010601011K
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption. Read More »
-
TSB #16NA372
This bulletin provides information on common diesel engine tick noises and how they are considered part of normal operation and no parts should be replaced for these normal operating conditions. Read More »
-
TSB #PIP5335C
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Read More »
-
TSB #18NA334
This informational bulletin provides information on Perceived Longer Crank, Misfire, Hesitation Feel and/or Surge conditions of the new L5P 6.6L Diesel Engine. Read More »
-
TSB #PIC5650F
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
-
TSB #PIP5212B
This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise. Technician should inspect the head gaskets to ensure are not installed backwards. Read More »
-
TSB #21NA113
This technical bulletin provides a procedure to perform a learn procedure for the turbo actuator. Read More »
-
TSB #20NA203
This informational bulletin explains how the regen works for the DEF system and how it works at different levels. Read More »
-
TSB #N192264210
Customer Satisfaction Program Closed Message sent. Read More »
-
TSB #17NA374
This informational bulletin advises the technician of how the Soot information has changed from grams to percentage. Read More »
-
TSB #22NA009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters. Read More »
-
TSB #PIP5628F
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D Read More »
-
TSB #20NA161
This informational bulletin advises the technician to check for a possible stuck oil pressure relief valve. Read More »
-
TSB #21NA113
This technical bulletin provides a procedure to perform a learn procedure for the turbo actuator. Read More »
-
TSB #22NA013
This technical bulletin provides a procedure for the technician to check and tighten the CAC plumbing if found loose. Read More »
-
TSB #PIP5684B
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
-
TSB #20NA010
This technical bulletin provides a procedure to replace the cooling fan if found contacting the shroud causing the customers concern. Read More »
-
TSB #10-06-05-002M
This informational bulletin provides information on Clean Exhaust Filter See Owner Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
-
TSB #16-NA-244
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system. Read More »
-
TSB #16-NA-380
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
-
TSB #19NA237
This informational bulletin explains how to identify possible DEF contamination. Read More »
-
TSB #20NA203
This informational bulletin explains how the regen works for the DEF system and how it works at different levels. Read More »
-
TSB #100605002H
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
-
TSB #19-NA-044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
-
TSB #15NA010
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states. Read More »
-
TSB #19-NA-044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
-
TSB #04-06-04-051H
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive. Read More »
-
TSB #21-NA-043
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
-
TSB #PIT5161J
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Read More »
-
TSB #05-06-04-022T
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
-
TSB #05-00-89-072F
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management. Read More »
-
TSB #04-06-04-051G
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive. Read More »
-
TSB #19-NA-044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy. Read More »
-
TSB #21-NA-043
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
-
TSB #22NA014
This technical provides a procedure to check for a possible faulty Reductant Injector and replace if the cause of the customers concern. Read More »
-
TSB #21NA025
This technical bulletin provides a procedure to replace the Fuel Power Module if found the cause of the customers concern. Read More »
-
TSB #19NA277
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to the vent and route down the fuel feed line and secure with zip ties. Read More »
-
TSB #19NA277
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to the vent and route down the fuel feed line and secure with zip ties. Read More »
-
TSB #19NA277
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to the vent and route down the fuel feed line and secure with zip ties. Read More »
-
TSB #PIP5630B
This Preliminary information communicates A vehicle may have a concern of no oil pressure and/or P0521 set. the releif valve in the pump is sticking or the number 1 main bearing is damaged. Drop oil pan and confirm #1 main is spun or not. Read More »
-
TSB #050604022Q
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
-
TSB #PIT5685
This Preliminary information communicates the location that dealers can find information to remove / delete the rear fuel tank from Chassis Cab trucks with RPO N2N dual fuel tanks. Read More »
-
TSB #17NA302
This informational bulletin provides information on availability for a locking gas cap for trucks are operated in high amount of dirt or dust which can migrate to the filler cap area. Read More »
-
TSB #18NA361
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
-
TSB #PIT5161K
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Read More »
-
TSB #19NA277
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to the vent and route down the fuel feed line and secure with zip ties. Read More »
-
TSB #20NA197
This technical bulletin provides a procedure to inspect and repair the fuel pressure sensor if found the cause of the customers concern. Read More »
-
TSB #04-06-04-051F
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive. Read More »
-
TSB #16NA383
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
-
TSB #20NA043
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
-
TSB #10-06-05-002M
This informational bulletin provides information on Clean Exhaust Filter See Owner Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
-
TSB #03-06-04-017T
This service bulletin provides information on availability of Diesel Fuel additives. Read More »
-
TSB #18-NA-103
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
-
TSB #16-NA-244
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system. Read More »
-
TSB #23-NA-027
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
-
TSB #23-NA-027
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
-
TSB #19-NA-237
This service bulletin explains how to identify possible DEF system contamination. Read More »
-
TSB #23-NA-027
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
-
TSB #03-06-04-017S
This service bulletin provides information on availability of Diesel Fuel additives. Read More »
-
TSB #16-NA-244
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system. Read More »
-
TSB #18-NA-361
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
-
TSB #18-NA-361
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
-
TSB #03-06-04-017R
This service bulletin provides information on availability of Diesel Fuel additives. Read More »
-
TSB #05-06-04-022T
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
-
TSB #16-NA-244
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system. Read More »
-
TSB #16-NA-380
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe. Read More »
-
TSB #18-NA-103
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
-
TSB #03-06-04-017Q
This service bulletin provides information on availability of Diesel Fuel additives. Read More »
-
TSB #20-NA-203
This informational bulletin explains how the regen works for the DEF system and how it works at different levels. Read More »
-
TSB #10-06-05-002K
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set. Read More »
-
TSB #19-NA-237
This informational bulletin explains how to identify possible DEF contamination. Read More »
-
TSB #18-NA-361
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
-
TSB #21-NA-043
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
-
TSB #N212346580-01
Customer Satisfaction Program - certain vehicles equipped with the Duramax diesel 6.6 liter engine and the optional engine-block heater cord, may have a condition in which the block heater cable function was disabled. Read More »
-
TSB #19NA237
This informational bulletin explains how to identify possible DEF contamination. Read More »
-
TSB #050604022Q
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL. Read More »
-
TSB #18NA334
This informational bulletin provides information on Perceived Longer Crank, Misfire, Hesitation Feel and/or Surge conditions of the new L5P 6.6L Diesel Engine. Read More »
-
TSB #17-NA-302
This informational bulletin provides information on availability for a locking gas cap for trucks are operated in high amount of dirt or dust which can migrate to the filler cap area. Read More »
-
TSB #16-NA-338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
-
TSB #PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine. Read More »
-
TSB #03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
-
TSB #22-NA-225
This information bulletin advises the technician the difference between a welch cap leak and the output seal of the t-case or transmission leaking ATF, causing the customer concern of a Red Fluid Leak from Center of Vehicle Located by ... Read More »
-
TSB #20-NA-142
This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving. Read More »
-
TSB #23-NA-153
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay. Read More »
-
TSB #15-00-89-004F
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
-
TSB #20-NA-142
This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving. Read More »
-
TSB #17-NA-066
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test. Read More »
-
TSB #17-NA-066
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test. Read More »
-
TSB #04-07-30-013E
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use. Read More »
-
TSB #08-07-30-026H
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. Read More »
-
TSB #PIC5650K
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
-
TSB #08-07-30-035G
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid. Read More »
-
TSB #PI0281J
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
-
TSB #16-NA-130
This service bulletin provides information for after installation of a replacement upper valve body, the transmission may have no Reverse and no 2nd gear. Read More »
-
TSB #99-04-20-002N
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation. Read More »
-
TSB #20-NA-142
This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving. Read More »
-
TSB #19-NA-136
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto ... Read More »
-
TSB #16-NA-338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, ... Read More »
-
TSB #20-NA-142
This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving. Read More »
-
TSB #19-NA-136
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling, Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto ... Read More »
-
TSB #20-NA-138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global ... Read More »
-
TSB #22-NA-225
This information advises the technician the difference between a welch cap leak and the output seal of the t-case or transmission leaking ATF causing the customers concern. Read More »
-
TSB #PIP5175E
This Preliminary Information communication provides information to the technician about vehicles that may have a delayed engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th ... Read More »
-
TSB #PIP5882
This Preliminary information communicates diagnostic aid to help isolate possible repeat thermal by-pass valve concern. Read More »
-
TSB #22-NA-185
This informational bulletin explains how the trans slip or flare can be a normal condition. Read More »
-
TSB #15-00-89-004E
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage. Read More »
-
TSB #06-00-89-031H
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification. Read More »
-
TSB #PIP5621C
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
-
TSB #22-NA-181
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission. Read More »
-
TSB #20-NA-142
This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving. Read More »
-
TSB #20-NA-142
This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving. Read More »
-
TSB #17-NA-066
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow test. Read More »
-
TSB #20-NA-050
This technical bulletin provides a procedure to clear the codes and test the Tcase if found that the customer has tried to shift the t-case from 4lo to Hi gears while driving. Read More »
-
TSB #PIP5794B
This Preliminary information communicates diagnostics to the dealer involving a vehicle shudder concern caused by the camshaft actuator system that can be mistaken for a transmission issue. Read More »
-
TSB #20-NA-209
This technical bulletin provides repair information to correct a customer concern of Service 4WD Message illuminated on Driver Information Center (DIC), DTCs C118D, C119B and/or C119C set. Read More »
-
TSB #20-NA-207
This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set. Read More »
-
TSB #21NA199
This informational bulletin advises the technician to replace the TBV if the transmission has any type of repair even if no problem was found, to replace the tbv. Read More »
-
TSB #19NA153
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM for metal. Read More »
-
TSB #19NA187
This bulletin provides additional information on how to graph a cylinder misfire and a possible diagnostic cause. Read More »
-
TSB #PIP5504F
This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Read More »
-
TSB #20NA019
This technical bulletin provides a procedure to replace the transmission shifter control if found the cause of the condition. Read More »
-
TSB #990420002K
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations. Read More »
-
TSB #16NA338
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record ... Read More »
-
TSB #16NA361
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been repaired for the flare and its still noticed. Read More »
-
TSB #PIT5202E
This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option ... Read More »
-
TSB #PIP4021D
This Preliminary Information communication provides information to the technician that a whine noise heard from the automatic transmission fluid pan hear with the the key on and engine off, or for up to one minute after the vehicle has ... Read More »
-
TSB #17-NA-066
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test. Read More »
-
TSB #PIT5206G
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? ... Read More »
-
TSB #PIP5531A
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with ... Read More »
-
TSB #PIP5621C
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. Read More »
-
TSB #20NA142
This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving. Read More »
-
TSB #16-NA-130
This service bulletin provides information for after installation of a replacement upper valve body, the transmission may have no Reverse and no 2nd gear. Read More »
-
TSB #21NA199
This informational bulletin advises the technician to replace the TBV if the transmission has any type of repair even if no problem was found, to replace the tbv. Read More »
-
TSB #19NA153
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM for metal. Read More »
-
TSB #PIE0560A
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a Service 4WD message being visible on the driver information center (DIC). Read More »
-
TSB #19NA136
This technical bulletin provides a procedure to change the diff fluid if found the cause of the customers concern. Read More »
-
TSB #20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements. Read More »
-
TSB #10-08-45-001H
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish. Read More »
-
TSB #20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements. Read More »
-
TSB #PI0592I
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
-
TSB #PIT5386J
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
-
TSB #20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements. Read More »
-
TSB #PIT5359D
This Preliminary Information communication provides information to the technician about vehicles that may have a radio backlighting will stay on even after the ignition has been turned off and the key has been removed for several minutes, ... Read More »
-
TSB #21-NA-135
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
-
TSB #21-NA-228
This bulletin provides a procedure to program the BCM to correct the customers concern of RKE idle Time-out. Read More »
-
TSB #21-NA-228
This bulletin provides a procedure to program the BCM to correct the customers concern of RKE idle Time-out. Read More »
-
TSB #23-NA-065
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
-
TSB #21-NA-228
This bulletin provides a procedure to program the BCM to correct the customers concern of RKE idle Time-out. Read More »
-
TSB #PIT5698D
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus. Read More »
-
TSB #07-08-49-020R
This informational bulletin provides information for the IPC odometer programming method quick reference guide. Read More »
-
TSB #23-NA-065
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
-
TSB #16-NA-222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations. Read More »
-
TSB #18-NA-103
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel ... Read More »
-
TSB #09-06-04-026X
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2. Read More »
-
TSB #23-NA-027
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
-
TSB #07-08-42-006S
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box ... Read More »
-
TSB #23-NA-125
This service bulletin provides information for dealers/technicians on Over the Air (OTA) and In Market Enhancement (IME) FAQs. Read More »
-
TSB #13-08-116-001I
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
-
TSB #PIT5509J
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
-
TSB #23-NA-027
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
-
TSB #20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements. Read More »
-
TSB #23-NA-027
This technical bulletin provides a procedure to test and replace the high-pressure fuel injector electrical connectors if found the cause of the MIL. Read More »
-
TSB #21-NA-043
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
-
TSB #23-NA-044
This service bulletin provides information on AGM batteries that require less frequent charging in storage. Read More »
-
TSB #20-NA-203
This informational bulletin explains how the regen works for the DEF system and how it works at different levels. Read More »
-
TSB #PIT5386H
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
-
TSB #21-NA-135
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
-
TSB #21-NA-228
This bulletin provides a procedure to program the BCM to correct the customers concern of RKE idle Time-out. Read More »
-
TSB #22-NA-205
This service bulletin provides information on Module Harvesting. Read More »
-
TSB #PI0592G
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961). Read More »
-
TSB #13-08-116-001H
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
-
TSB #21-NA-068
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
-
TSB #21-NA-027
This technical bulletin provides a procedure to install 2 way tape to correct a condition of Trailering Connector Loose Within Rear Bumper. Read More »
-
TSB #PIT5569B
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC. Read More »
-
TSB #PIT5287G
This Preliminary Information communication provides information to the technician with the correct way to remove the front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. Read More »
-
TSB #PIP4670J
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
-
TSB #20-NA-209
This technical bulletin provides repair information to correct a customer concern of Service 4WD Message illuminated on Driver Information Center (DIC), DTCs C118D, C119B and/or C119C set. Read More »
-
TSB #N212346580-01
Customer Satisfaction Program - certain vehicles equipped with the Duramax diesel 6.6 liter engine and the optional engine-block heater cord, may have a condition in which the block heater cable function was disabled. Read More »
-
TSB #18-NA-161
This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery. Read More »
-
TSB #20-NA-207
This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set. Read More »
-
TSB #PIT5386G
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
-
TSB #21NA113
This technical bulletin provides a procedure to perform a learn procedure for the turbo actuator. Read More »
-
TSB #PIT5743A
This Preliminary information communicates diagnostic tips when trying to root cause a SES MIL with DTC's B2B0D and B2B0E. Main cause is aftermarket electrical devices spliced into the ignition main fuses. Read More »
-
TSB #PIT5509H
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
-
TSB #21NA025
This technical bulletin provides a procedure to replace the Fuel Power Module if found the cause of the customers concern. Read More »
-
TSB #070842006P
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box ... Read More »
-
TSB #20NA212
This technical bulletin provides repair information to correct a customer concern of IPC Gauges Inoperative or Fluctuate, No Crank, Start then Stall. Read More »
-
TSB #20NA043
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
-
TSB #20NA203
This informational bulletin explains how the regen works for the DEF system and how it works at different levels. Read More »
-
TSB #20NA176
This technical bulletin provides a procedure to update the GPCM if found the cause of the customers concern. Read More »
-
TSB #PIT5206G
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? ... Read More »
-
TSB #PIT5195F
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Read More »
-
TSB #HT-03.03.2020
Hypertech Inline Speedometer Calibrator Module Installation Instructions Read More »
-
TSB #PIE0554
This engineering information (EI) is requesting information from the field to perform the check list provided and contact the engineer in regards to Instrument Panel Cluster (IPC) Gages at Zero, Multiple Warning Lights On, No Chimes ... Read More »
-
TSB #DOR-D8C4T-03
This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. Read More »
-
TSB #DOR-E2P5T-03
This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. Read More »
-
TSB #19NA228
This technical provides a procedure to locate, disconnect and re-connect the TCM electrical connector if found the cause of the customers concerns. Read More »
-
TSB #PIT5288G
This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information ... Read More »
-
TSB #PIE0511A
This engineering informational bulletin is requesting information clear the codes and perform the glow plug learn procedure. Read More »
-
TSB #100845001G
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish. Read More »
-
TSB #PIP4670G
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. Read More »
-
TSB #060847001O
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
-
TSB #19NA109
This informational bulletin provides information for dealers/technicians on Oil Life Monitor Engine Control Module Update. Read More »
-
TSB #PIT5311E
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver ... Read More »
-
TSB #PIT5540A
This Preliminary Information communication provides information to the technician about vehicles that have a low voltage reading on the volt gauge during the first several minutes after a cold start. Read More »
-
TSB #PIT5386E
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
-
TSB #PIE0511
This engineering informational bulletin is requesting information from the field to determine a root cause for a condition of Service Engine Soon (SES) Light On, DTCs P06C5, P06CC, P066A, P066C, P066E, P067A, P067C, P067E, P068C, P068E, ... Read More »
-
TSB #PIT5282E
This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Read More »
-
TSB #PIT5287E
This Preliminary Information communication provides information to the technician with the correct way to remove the front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. Read More »
-
TSB #PIT5391E
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be ... Read More »
-
TSB #PIT5326C
This Preliminary Information communication provides information to the technician about the Upfitters questions about installing aftermarket electrical accessories. Read More »
-
TSB #18366
Service Update. Certain vehicles that are equipped with a Duramax diesel engine, the engine control module (ECM) may not take the appropriate remedial actions if an exhaust gas temperature sensor becomes disconnected. Read More »
-
TSB #PIT5962A
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
-
TSB #20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements. Read More »
-
TSB #20NA132
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements. Read More »
-
TSB #18NA161
This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery. Read More »
-
TSB #18NA180
This Warranty Administration Bulletin Provides High Voltage Battery Exchange Process Information. Read More »
-
TSB #110849001Y
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off. Read More »
-
TSB #PIT5311F
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver ... Read More »
-
TSB #100089005H
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. Read More »
-
TSB #PIT5311F
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver ... Read More »
-
TSB #N192275630-03
Customer Satisfaction Program - Certain vehicles may have a condition in which the electronic brake controlmodule is less likely to activate the optional integrated brake assist. Normal braking capability functions as intended. Read More »
-
TSB #21-NA-228
This bulletin provides a procedure to program the BCM to correct the customers concern of RKE idle Time-out. Read More »
-
TSB #PIC5650K
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Read More »
-
TSB #20NA212
This technical bulletin provides repair information to correct a customer concern of IPC Gauges Inoperative or Fluctuate, No Crank, Start then Stall. Read More »
-
TSB #07-08-49-020R
This informational bulletin provides information for the IPC odometer programming method quick reference guide. Read More »
-
TSB #20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements. Read More »
-
TSB #PIP5632G
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
-
TSB #PIP4902Q
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
-
TSB #PIC6365A
This Preliminary information communicates information to dealers advising certain Over the air updates and USB updates have been temporarily suspended. Read More »
-
TSB #17NA276
This informational bulletin provides information on Loss of Phone Pairing or Favorites, Last Setting of Volume, Station, App, and Audio Settings Change When Vehicle Shuts Down in Demo Mode and that this is considered a normal ... Read More »
-
TSB #22NA012
This service bulletin provides information for dealers/technicians on Stone Chip/Membrane Damage, Broken Connector and/or Sensor Retaining Tabs, and/or Paint Damage of Park Assist Sensors. Read More »
-
TSB #PIT5662F
This Preliminary information communicates information to diagnose DTC C056D or C056E. Read More »
-
TSB #N212346580-01
Customer Satisfaction Program - certain vehicles equipped with the Duramax diesel 6.6 liter engine and the optional engine-block heater cord, may have a condition in which the block heater cable function was disabled. Read More »
-
TSB #02-08-42-001J
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage. Read More »
-
TSB #21-NA-135
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
-
TSB #07-08-42-006S
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box ... Read More »
-
TSB #01-08-42-001P
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement Guidelines. Read More »
-
TSB #01-08-42-001O
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. Read More »
-
TSB #07-08-42-006R
This service bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box ... Read More »
-
TSB #18NA001
This informational bulletin explains normal operation of HID bulbs when driving over road irregularities. Read More »
-
TSB #PIT5288G
This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information ... Read More »
-
TSB #18NA360
This technical bulletin provides a procedure to replace the side mirror cameras if found the cause of the reduced key fob range. Read More »
-
TSB #24-NA-046
This technical bulletin provides a procedure to correct the condition of Suction Cup Marks on Window Glass. Read More »
-
TSB #PI0754F
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic. Read More »
-
TSB #DOR-D8C4T-03
This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. Read More »
-
TSB #DOR-E2P5T-03
This SKU is a Power Window Regulator and Motor Assembly. The customer communication requested return of unsold inventory to inspect the software. Read More »
-
TSB #PIC5260E
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks. Read More »
-
TSB #PIT5099G
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
-
TSB #12-01-37-001F
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service. Read More »
-
TSB #21-NA-097
This technical bulletin provides a procedure to install a pice of foam between the heater core pipes to correct the customers concern. Read More »
-
TSB #PIT5099F
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Read More »
-
TSB #PIP5540J
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. Read More »
-
TSB #99-09-40-005I
This service bulletin provides information on availability for a seat belt extender. Read More »
-
TSB #19-NA-255
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
-
TSB #19-NA-255
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
-
TSB #19-NA-255
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
-
TSB #PI0281K
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
-
TSB #99-08-51-001F
This service bulletin provides information on Paintless Dent Repair Process. Read More »
-
TSB #PI0281J
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
-
TSB #23-NA-059
This technical bulletin provides a procedure to correct the condition of Gap at Door Armrest Decorative Trim to the Armrest/Door Switch. Read More »
-
TSB #22-NA-018
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
-
TSB #PI0754F
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic. Read More »
-
TSB #19-NA-255
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
-
TSB #99-00-89-019X
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
-
TSB #PI0281I
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
-
TSB #12-08-51-002N
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
-
TSB #19NA255
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
-
TSB #18NA383
This technical bulletin provides repair information to correct a customer concern of water found in rear interior of cab due to water leak at rear sliding window. Read More »
-
TSB #18NA239
This technical bulletin provides a procedure to add washers on the lower column mounting bracket locations due to the shaft laying on the metal support at the bottom of the column. Read More »
-
TSB #19NA255
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
-
TSB #PIT4250J
This Preliminary Information communication provides information to the technician about vehicles that have water or dust from the openings under the bed rails near the stake pockets. Read More »
-
TSB #PI0281I
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers. Read More »
-
TSB #PIT6119
This Preliminary information communicates an issue where the minor tailgate will not open due to an aftermarket device installed on the vehicle. Read More »
-
TSB #PIT3227P
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Read More »
-
TSB #PIT5570B
This Preliminary Information communication provides the technician with weight capacity for the tailgate and cargo loops in the bed. Read More »
-
TSB #18-NA-279
This service bulletin provides information for dealers/technicians on the process to disable and enable passive unlocking. Read More »
-
TSB #PIT4506G
This Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks and Utilities may ask if they can lower their tire pressures. Read More »
-
TSB #20-NA-159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only). Read More »
-
TSB #20-NA-159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only). Read More »
-
TSB #00-00-90-002M
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
-
TSB #PIT3271N
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. Read More »
-
TSB #PIT4261H
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
-
TSB #PIT3271M
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. Read More »
-
TSB #PIT3271K
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. Read More »
-
TSB #000310003Z
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only). Read More »
-
TSB #050310020G
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires. Read More »
-
TSB #080310006G
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
-
TSB #010310003R
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty ... Read More »
-
TSB #07-03-16-004E
This service bulletin provides information for tire pressure monitoring (TPM) system concerns. Read More »
-
TSB #00-03-10-006P
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV). Read More »
-
TSB #17-NA-052
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
-
TSB #03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns. Read More »
-
TSB #20-NA-159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only). Read More »
-
TSB #17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
-
TSB #20-NA-159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only). Read More »
-
TSB #12-03-10-001E
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
-
TSB #17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement. Read More »
-
TSB #12-03-10-001D
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel). Read More »
-
TSB #21-NA-043
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
-
TSB #20-NA-159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only). Read More »
-
TSB #07-03-16-004E
This service bulletin provides information for tire pressure monitoring (TPM) system concerns. Read More »
-
TSB #00-00-90-002M
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
-
TSB #22-NA-257
This service bulletin provides information on Dealer Installed LPO Wheel Installation and Return Process. Read More »
-
TSB #PIT3271N
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. Read More »
-
TSB #20-NA-159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only). Read More »
-
TSB #21-NA-043
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer. Read More »
-
TSB #20-NA-159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only). Read More »
-
TSB #17-NA-052
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
-
TSB #PIT3271M
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. Read More »
-
TSB #RFI20210526_939-
The complete Communication ID is: RFI20210526_939-187 and was communicated to customers on May 26, 2021. The Communication ID field did not permit me to enter the complete Communication ID as it is in our internal system. Read More »
-
TSB #PIT3271K
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. Read More »
-
TSB #050307009I
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
-
TSB #080310006G
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
-
TSB #PIT5451C
This Preliminary Information communication provides information to the technician about vehicles that have a vibration at highway speed. Technician will need to replace the wheel for a rolled lip of aluminum in the hub opening. Read More »
-
TSB #PIT5509J
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when ... Read More »
-
TSB #17-NA-350
This informational bulletin provides explanation of a normal condition of a loose-fitting ball receiver in the gooseneck. Read More »
-
TSB #17-NA-350
This informational bulletin provides explanation of a normal condition of a loose fitting ball receiver in the gooseneck. Read More »
-
TSB #17NA350
This informational bulletin provides explanation of a normal condition of a loose fitting ball receiver in the gooseneck. Read More »
-
TSB #PIT5282E
This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Read More »
-
TSB #PIT5432B
This Preliminary Information communication provides information to the technician about vehicles that have a Shudder, bounce, bucking from the rear of the truck while braking when towing a gooseneck or fifth wheel trailer. Read More »
-
TSB #18NA377
This technical bulletin provides repair information to correct a customer concern of front seat lateral movement and/or click type noise while driving. Read More »
-
TSB #18NA377
This technical bulletin provides repair information to correct a customer concern of front seat lateral movement and/or click type noise while driving. Read More »
-
TSB #PIT4322P
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
-
TSB #PIT4322M
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
-
TSB #PIT4322K
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Read More »
-
TSB #PIT5551N
This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert". Read More »
-
TSB #N192282190
Customer Satisfaction Program - Certain 2019 model year GMC Sierra 2500/3500 vehicles, may have incorrect language in the Forward Auto Braking (FAB) section of the owner manual which states, ?If the vehicle has Forward Collision Alert ... Read More »
-
TSB #18NA360
This technical bulletin provides a procedure to replace the side mirror cameras if found the cause of the reduced key fob range. Read More »
-
TSB #PIT5386J
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
-
TSB #PIT5386H
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
-
TSB #PIT5921
This Preliminary information communicates diagnostics aids for rear view camera issues that may be encountered. Read More »
-
TSB #PIT5386G
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
-
TSB #PIT5386E
This Preliminary Information communication provides information to the technician about vehicles that are found to have a back-up alarm inoperative during the Pre-Delivery Inspection. Read More »
-
TSB #PIT5552C
This Preliminary information communicates repair information for the rear vision camera or surround vision camera image being: - Yellow - Blurry - Distorted - Image scrolling - Image with NO gridlines - Screen is blue with ... Read More »
-
TSB #PIP4902P
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
-
TSB #20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements. Read More »
-
TSB #17-NA-052
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed. Read More »
-
TSB #20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements. Read More »
-
TSB #17-NA-302
This informational bulletin provides information on availability for a locking gas cap for trucks are operated in high amount of dirt or dust which can migrate to the filler cap area. Read More »
-
TSB #07-00-89-037S
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs. Read More »
-
TSB #11-00-89-005X
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only). Read More »
-
TSB #23-NA-219
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories. Read More »
-
TSB #20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements. Read More »
-
TSB #21-NA-135
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles that request to disable or enable content. Read More »
-
TSB #21-NA-228
This bulletin provides a procedure to program the BCM to correct the customers concern of RKE idle Time-out. Read More »
-
TSB #21-NA-228
This bulletin provides a procedure to program the BCM to correct the customers concern of RKE idle Time-out. Read More »
-
TSB #22-NA-225
This information bulletin advises the technician the difference between a welch cap leak and the output seal of the t-case or transmission leaking ATF, causing the customer concern of a Red Fluid Leak from Center of Vehicle Located by ... Read More »
-
TSB #23-NA-065
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
-
TSB #21-NA-228
This bulletin provides a procedure to program the BCM to correct the customers concern of RKE idle Time-out. Read More »
-
TSB #23-NA-154
This bulletin provides information on Warranty Administration a?? Required Operating Procedures - 8 Points (U.S. Only). Read More »
-
TSB #07-08-49-020R
This informational bulletin provides information for the IPC odometer programming method quick reference guide. Read More »
-
TSB #18-NA-306
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
-
TSB #09-00-89-016H
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014. Read More »
-
TSB #23-NA-065
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States. Read More »
-
TSB #01-00-89-010R
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern. Read More »
-
TSB #21-NA-026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
-
TSB #23-NA-125
This service bulletin provides information for dealers/technicians on Over the Air (OTA) and In Market Enhancement (IME) FAQs. Read More »
-
TSB #16-NA-158
This service bulletin describes the U.S. Dealer Special Tool Loan Program process. Read More »
-
TSB #22-NA-244
This service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty Coverage Period. Read More »
-
TSB #17-NA-350
This informational bulletin provides explanation of a normal condition of a loose-fitting ball receiver in the gooseneck. Read More »
-
TSB #10-08-110-001J
This service bulletin provides information on proper use of floor mats. Read More »
-
TSB #20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements. Read More »
-
TSB #23-NA-059
This technical bulletin provides a procedure to correct the condition of Gap at Door Armrest Decorative Trim to the Armrest/Door Switch. Read More »
-
TSB #22-NA-018
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
-
TSB #23-NA-044
This service bulletin provides information on AGM batteries that require less frequent charging in storage. Read More »
-
TSB #15-NA-017
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment. Read More »
-
TSB #07-03-16-004E
This service bulletin provides information for tire pressure monitoring (TPM) system concerns. Read More »
-
TSB #21-NA-068
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
-
TSB #21-NA-228
This bulletin provides a procedure to program the BCM to correct the customers concern of RKE idle Time-out. Read More »
-
TSB #22-NA-244
This service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty Coverage Period. Read More »
-
TSB #21-NA-068
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with ... Read More »
-
TSB #05-00-89-029E
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations. Read More »
-
TSB #22-NA-143
This service bulletin provides information for dealers/technicians on Handsfree Apple Iphone Call Static conditions equipped with IOB Radio. Read More »
-
TSB #PIT5569B
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC. Read More »
-
TSB #PIT4261H
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Read More »
-
TSB #22-NA-135
This warranty admin bulletin covers information on Essential Tools that include Consumable Parts. Read More »
-
TSB #12-01-37-001F
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service. Read More »
-
TSB #21-NA-026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen. Read More »
-
TSB #16-NA-109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear. Read More »
-
TSB #22-NA-106
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
-
TSB #22-NA-070
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part replacements. Read More »
-
TSB #01-00-89-010P
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern. Read More »
-
TSB #22-NA-070
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part replacements. Read More »
-
TSB #17-NA-052
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint. GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY). Read More »
-
TSB #12-08-51-002N
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
-
TSB #PIT5746B
This Preliminary information communicates information on how dealers can contact the supplier for Associated Accessories offered through GM. Read More »
-
TSB #20NA043
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
-
TSB #20NA203
This informational bulletin explains how the regen works for the DEF system and how it works at different levels. Read More »
-
TSB #PIP5832
This Preliminary information communicates to the dealer an issue where a vehicle may be exhibiting an engine noise condiion. The dealer is instructed on how to isolate the noise to a specific area of the engine for further diagnosis. Read More »
-
TSB #19NA104
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area. Read More »
-
TSB #PIT3099U
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Read More »
-
TSB #070089037P
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs. Read More »
-
TSB #100089006H
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only). Read More »
-
TSB #20NA203
This informational bulletin explains how the regen works for the DEF system and how it works at different levels. Read More »
-
TSB #20NA212
This technical bulletin provides repair information to correct a customer concern of IPC Gauges Inoperative or Fluctuate, No Crank, Start then Stall. Read More »
-
TSB #18NA098
This informational bulletin provides information for the technicians on where to look on the Duramax engine for coolant leaks. Read More »
-
TSB #19NA187
This bulletin provides additional information on how to graph a cylinder misfire and a possible diagnostic cause. Read More »
-
TSB #19NA237
This informational bulletin explains how to identify possible DEF contamination. Read More »
-
TSB #20NA043
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
-
TSB #20NA203
This informational bulletin explains how the regen works for the DEF system and how it works at different levels. Read More »
-
TSB #20NA197
This technical bulletin provides a procedure to inspect and repair the fuel pressure sensor if found the cause of the customers concern. Read More »
-
TSB #20NA142
This Technical bulletin provides a repair to correct a condition of Shudder/Surging While Driving. Read More »
-
TSB #19NA255
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
-
TSB #19NA277
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to the vent and route down the fuel feed line and secure with zip ties. Read More »
-
TSB #PIP5684B
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual. Read More »
-
TSB #PIT5206G
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? ... Read More »
-
TSB #PIT5564C
This Preliminary information communicates an issue with aftermarket USB chargers causing SIR DTC's to set. Read More »
-
TSB #19NA277
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to the vent and route down the fuel feed line and secure with zip ties. Read More »
-
TSB #20NA043
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
-
TSB #20NA006
This informational bulletin explains there is another steering hose that can be used for cold weather drivers that experience a steering hose leak. Read More »
-
TSB #N192282190
Customer Satisfaction Program - Certain 2019 model year GMC Sierra 2500/3500 vehicles, may have incorrect language in the Forward Auto Braking (FAB) section of the owner manual which states, ?If the vehicle has Forward Collision Alert ... Read More »
-
TSB #18NA073
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement. Read More »
-
TSB #110089002D
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period. Read More »
-
TSB #050307009I
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment. Read More »
-
TSB #PI0689D
This preliminary information bulletin provides a procedure for installing a aftermarket tool or utility box. Read More »
-
TSB #16NA383
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
-
TSB #100089009D
This informational bulletin provides information on key code security rules and information on GM keycode look-up applications. Read More »
-
TSB #080089014F
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
-
TSB #19NA270
This technical bulletin provides repair information to correct a customer concern of Phone Ringer Volume Turned Down or Too Quiet. Read More »
-
TSB #080310006G
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
-
TSB #120851002K
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
-
TSB #N192264210 Messa
Customer Satisfaction Program. Stock VIN List sent. Read More »
-
TSB #DORD8R3N09
This SKU is a Tire Hoist Assembly. The customer communication requested return of unsold inventory to inspect for the shape of the centerpiece of the tire hoist being round when it should be square. Read More »
-
TSB #1308116001E
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
-
TSB #000601012J
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
-
TSB #090604026Q
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2. Read More »
-
TSB #16NA119
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
-
TSB #080089014E
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
-
TSB #PIT5564B
This Preliminary information communicates an issue with aftermarket USB chargers causing SIR DTC's to set. Read More »
-
TSB #120089002C
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer. Read More »
-
TSB #090089002P
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
-
TSB #060089026O
This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND). Read More »
-
TSB #080089014C
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
-
TSB #18NA361
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
-
TSB #PIT5570B
This Preliminary Information communication provides the technician with weight capacity for the tailgate and cargo loops in the bed. Read More »
-
TSB #PIT5432B
This Preliminary Information communication provides information to the technician about vehicles that have a Shudder, bounce, bucking from the rear of the truck while braking when towing a gooseneck or fifth wheel trailer. Read More »
-
TSB #12-00-89-003B
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only). Read More »
-
TSB #PIT5564C
This Preliminary information communicates an issue with aftermarket USB chargers causing SIR DTC's to set. Read More »
-
TSB #PIT5586C
This Preliminary information communicates a customer concern of IPC gauges inoperative or fluctuate, No Start, No Crank, SIR Light / Service Airbag Message, Service Suspension Message, Radio display blank, Steering Wheel Controls (SWC) ... Read More »
-
TSB #030603004X
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements. Read More »
-
TSB #17NA330
This informational bulletin provides information for the customer to pair their phone in order for the push to talk button on the steering wheel control to work. Read More »
-
TSB #PIT5545C
This Preliminary information communicates Content Theft Deterrent RPO UTJ is included and only available with Remote Vehicle Start RPO BTV. Read More »
-
TSB #PIT6122
This Preliminary information communicates to dealers of a known issue with failed map update Read More »
-
TSB #PIT5387N
This Preliminary Information communication provides information to the technician how to repair vehicles that Instrument Panel Cluster, Radio, and Heater-Vent-Air Conditioning display blanks out, Bluetooth phone or Pandora connection ... Read More »
-
TSB #N212346580-01
Customer Satisfaction Program - certain vehicles equipped with the Duramax diesel 6.6 liter engine and the optional engine-block heater cord, may have a condition in which the block heater cable function was disabled. Read More »
-
TSB #16-NA-372
This bulletin provides information on common diesel engine tick noises and how they are considered part of normal operation and no parts should be replaced for these normal operating conditions. Read More »
-
TSB #04-06-04-051F
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive. Read More »
-
TSB #20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements. Read More »
-
TSB #23-NA-103
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
-
TSB #24-NA-040
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC. Read More »
-
TSB #18-NA-099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
-
TSB #PIP5601B
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Read More »
-
TSB #23-NA-219
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories. Read More »
-
TSB #05-00-89-029F
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations. Read More »
-
TSB #99-00-89-019Y
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program. Read More »
-
TSB #02-00-89-002W
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only). Read More »
-
TSB #10-00-89-006J
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only). Read More »
-
TSB #23-NA-154
This bulletin provides information on Warranty Administration a?? Required Operating Procedures - 8 Points (U.S. Only). Read More »
-
TSB #18-NA-306
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
-
TSB #PIP5358C
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Read More »
-
TSB #23-NA-103
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC). Read More »
-
TSB #02-00-89-002V
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
-
TSB #04-00-89-015Z
This bulletin provides information on Warranty Administration a?? Required Operating Procedures - 8 Points (U.S. Only). Read More »
-
TSB #11-00-89-005V
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only). Read More »
-
TSB #17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy. Read More »
-
TSB #18-NA-146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only). Read More »
-
TSB #18-NA-263
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S. Only). Read More »
-
TSB #00-00-90-002M
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks. Read More »
-
TSB # 02-00-89-002U
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only). Read More »
-
TSB #09-00-89-008F
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process. Read More »
-
TSB #PIT5746C
This Preliminary information communicates information on how dealers can contact the supplier for Associated Accessories offered through GM. Read More »
-
TSB #PIP5632G
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
-
TSB #PIP4902Q
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Read More »
-
TSB #10-00-89-006I
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only). Read More »
-
TSB #22-NA-195
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada. Read More »
-
TSB #01-00-89-010Q
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern. Read More »
-
TSB #11-00-89-005U
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only). Read More »
-
TSB #18-NA-306
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
-
TSB #11-00-89-005T
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only). Read More »
-
TSB #04-00-89-015X
This bulletin provides information on Warranty Administration a?? Required Operating Procedures - 8 Points (U.S. Only). Read More »
-
TSB #18-NA-306
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA). Read More »
-
TSB #22-NA-070
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part replacements. Read More »
-
TSB #22-NA-106
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires. Read More »
-
TSB #18-NA-099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim. Read More »
-
TSB #22NA018
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only). Read More »
-
TSB #N192264210
Customer Satisfaction Program Closed Message sent. Read More »
-
TSB #090089002R
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
-
TSB #000310003Z
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only). Read More »
-
TSB #PIE0560A
This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards to a Service 4WD message being visible on the driver information center (DIC). Read More »
-
TSB #16NA119
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada. Read More »
-
TSB #080089014F
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
-
TSB #100089006G
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only). Read More »
-
TSB #19NA232
This informational bulletin provides tips for showing a way to confirm if its a mechanical engine issue or not. Read More »
-
TSB #100089009C
This informational bulletin provides information on key code security and information on GM key code look up applications. Read More »
-
TSB #18NA306
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only). Read More »
-
TSB #010089010N
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
-
TSB #PIT4529E
This preliminary information explains that there are differences between the Elevated Idle, PTO and High Idle options. Read More »
-
TSB #19NA153
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM for metal. Read More »
-
TSB #060847001O
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module. Read More »
-
TSB #PIP5629A
This Preliminary information communicates to the dealer technicians to refer to service bulletin 19-NA-109. Read More »
-
TSB #PIE0511
This engineering informational bulletin is requesting information from the field to determine a root cause for a condition of Service Engine Soon (SES) Light On, DTCs P06C5, P06CC, P066A, P066C, P066E, P067A, P067C, P067E, P068C, P068E, ... Read More »
-
TSB #010089010M
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS). Read More »
-
TSB #080089014D
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC). Read More »
-
TSB #120851002I
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information and repair procedures. Read More »
-
TSB #040089015T
This warranty administration bulletin provides policy information on required operating procedures. Read More »
-
TSB #20NA203
This informational bulletin explains how the regen works for the DEF system and how it works at different levels. Read More »
-
TSB #20NA212
This technical bulletin provides repair information to correct a customer concern of IPC Gauges Inoperative or Fluctuate, No Crank, Start then Stall. Read More »
-
TSB #PIT5206G
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? ... Read More »
-
TSB #19NA277
This technical bulletin provides a procedure to replace the fuel tank, sending unit and install a piece of fuel hose to the vent and route down the fuel feed line and secure with zip ties. Read More »
-
TSB #090089002R
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer. Read More »
-
TSB #20NA043
This informational bulletin advises the technician to not replace the TMAP sensor, clean it using air or harsh chemicals but allow time for the sensor to thaw. Read More »
-
TSB #20NA006
This informational bulletin explains there is another steering hose that can be used for cold weather drivers that experience a steering hose leak. Read More »
-
TSB #20NA006
This informational bulletin explains there is another steering hose that can be used for cold weather drivers that experience a steering hose leak. Read More »
-
TSB #16NA383
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier ... Read More »
-
TSB #100089009D
This informational bulletin provides information on key code security rules and information on GM keycode look-up applications. Read More »
-
TSB #19NA270
This technical bulletin provides repair information to correct a customer concern of Phone Ringer Volume Turned Down or Too Quiet. Read More »
-
TSB #19NA255
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only). Read More »
-
TSB #080310006G
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel ... Read More »
-
TSB #100845001G
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish. Read More »
-
TSB #1308116001E
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them. Read More »
-
TSB #000601012J
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts. Read More »
-
TSB #19NA136
This technical bulletin provides a procedure to change the diff fluid if found the cause of the customers concern. Read More »
-
TSB #PIP5629
This Preliminary information communicates to the dealer technicians that the oil life monitoring system for 2019 Duramax 6.6 L5P is under investigation by engineering. Read More »
-
TSB #18NA361
This technical bulletin provides a procedure to flush the cooler lines to validate if there is excessive debris in the fuel system caused by a failed part. Read More »
-
TSB #PIT5790C
This Preliminary information communicates a concern where the radio will reboot when adjusting the volume intermittently and that engineering is investigating. Read More »
-
TSB #17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy. Read More »
-
TSB #PIT5962A
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses. Read More »
-
TSB #11-00-89-005W
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only). Read More »
-
TSB #11-00-89-005V
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only). Read More »
-
TSB #PI0754F
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic. Read More »
-
TSB #01-00-89-010O
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern. Read More »
-
TSB #090604026V
Information. Read More »