2014 Hyundai Equus
TSBs (Technical Service Bulletins)
Technical Service Bulletins (TSBs) for the 2014 Equus are official communications between Hyundai & their dealerships that describe processes for troubleshooting or fixing certain common problems. All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
-
TSB #20-SS-001H
This bulletin describes the requirements for all wheel alignment and/or vehicle tracking claims and best practices when diagnosing and conducting alignment-related repairs for all models and model years. Read More »
-
TSB #21-BR-002H
This bulletin provides best practice recommendations when performing brake service procedures. Read More »
-
TSB #20-BR-002H
This bulletin describes the procedure to inspect and identify fluid which may appear around the brake caliper area. Read More »
-
TSB #19-AT-008H
When servicing a vehicle with a ?Check Engine light? and any of the DTCs listed below, follow the Service Procedure and replace the related solenoid and E-module. Read More »
-
TSB #19-AT-005H
If you are servicing a vehicle with a ?Check Engine light? and any of the DTCs listed below, follow the Service Procedure and replace the E-module. Read More »
-
TSB #23-EM-005H
This bulletin provides important checkpoint guidelines when performing engine oil and filter change services. Read More »
-
TSB #22-EM-010H
Follow the guidelines outlined in this bulletin to inspect and clean or replace certain components of the engine intake system accordingly during engine short block or sub-assembly replacement. Read More »
-
TSB #21-EM-004H
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required ... Read More »
-
TSB #21-EM-003H
This bulletin provides the inspection procedure and repair guidelines for certain vehicles listed below. Read More »
-
TSB #24-AT-002H
This TSB provides a procedure to diagnose and replace, if necessary, an automatic transmission with Incorrect Ratio DTC (transmission clutch slip in gear above limit) listed on Page 2. Read More »
-
TSB #21-AT-018H
This bulletin describes the procedure to replace the 35R and 4&OD solenoids for a shift flare and/or harsh shift during the 2~3, 3~4 or 4~5 upshift. Read More »
-
TSB #20-AT-016H
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions: Read More »
-
TSB #19-AT-021H-1
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. Read More »
-
TSB #19-AT-014H
This bulletin provides a procedure to diagnose an 8-speed automatic transaxle with a harsh and/or delayed shift using GDS. Read More »
-
TSB #19-AT-011H
The procedure describes the procedure to check the ATF level for 8-speed Rear-Wheel-Drive vehicles. Read More »
-
TSB #19-AT-007H
This bulletin provides a procedure to transfer oil pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the TCU learning time and improve the shift quality. Read More »
-
TSB #19-FL-003H
This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Read More »
-
TSB #19-AT-008H
When servicing a vehicle with a ?Check Engine light? and any of the DTCs listed below, follow the Service Procedure and replace the related solenoid and E-module. Read More »
-
TSB #19-AT-011H
The procedure describes the procedure to check the ATF level for 8-speed Rear-Wheel-Drive vehicles. Read More »
-
TSB #19-AT-007H
This bulletin provides a procedure to transfer oil pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the TCU learning time and improve the shift quality. Read More »
-
TSB #19-AT-008H
When servicing a vehicle with a ?Check Engine light? and any of the DTCs listed below, follow the Service Procedure and replace the related solenoid and E-module. Read More »
-
TSB #5NP-H3D9Z-03
The following vehicles are equipped with an 8-speed automatic transmission. The ATF level can be checked by the procedure shown below. Read More »
-
TSB #5NP-J4N8R-01
DO NOT REPLACE THE TRANSMISSION FOR THE DTC LISTED. INSTEAD, FOLLOW THE REPAIR PROCEDURE AND REPLACE THE E-MODULE. Read More »
-
TSB #5NP-D2Y6N-12
"UPDATE THE WARRANTY INFORMATION. DESCRIPTION: DO NOT REPLACE THE TRANSMISSION FOR THE DTC LISTED BELOW. INSTEAD, FOLLOW THE REPAIR PROCEDURE AND REPLACE THE E-MODULE." Read More »
-
TSB #5NP-W7J6Y-11
"AUTOMATIC TRANSMISSION SOLENOID & SENSOR REPLACEMENT FOR DTC P0741, P0743, P0748, P0753, P0758, P075A, P0763, P0768, P0773, P2709 & P0841" Read More »
-
TSB #5NP-Q9X6P-10
THIS BULLETIN PROVIDES A PROCEDURE TO TRANSFER PRESSURE DATA TO THE TCM USING GDS MOBILE. THIS PROCEDURE IS NECESSARY TO REDUCE THE TCM LEARNING TIME AND IMPROVE THE SHIFT QUALITY. Read More »
-
TSB #5NP-B6E2P-10
"THE PCM OR TCM CONTAINS LOGIC TO ADJUST SOLENOID DUTY AND LINE PRESSURE AS NEEDED TO COMPENSATE FOR NORMAL CLUTCH WEAR OVER THE LIFE OF THE TRANSAXLE. Read More »
-
TSB #5NP-H3D9Z-03
The following vehicles are equipped with an 8-speed automatic transmission. The ATF level can be checked by the procedure shown below. Read More »
-
TSB #5NP-B6E2P-10
"THE PCM OR TCM CONTAINS LOGIC TO ADJUST SOLENOID DUTY AND LINE PRESSURE AS NEEDED TO COMPENSATE FOR NORMAL CLUTCH WEAR OVER THE LIFE OF THE TRANSAXLE. Read More »
-
TSB #20-EE-003H
This bulletin provides information on identifying dealer stock vehicles with either: a?? A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. a?? A 30 Day alert - vehicle has not started and reported an SOC in 30 days. Read More »
-
TSB #20-BE-001H
This bulletin provides guidelines to inspect the USB, head unit, and multi-box for common connection conditions. 2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. Read More »
-
TSB #19-BE-010H
This bulletin provides information related to clearing all Diagnostic codes for vehicles equipped with the Blue Link system (Gen 1). Read More »
-
TSB #19-FL-003H
This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Read More »
-
TSB #14-01-035
HYUNDAI EQUUS: SOME VEHICLES MAY SHOW A MALFUNCTION INDICATOR LAMP. *LJ Read More »
-
TSB #TSB-14-01-035
HYUNDAI: MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATED, ON SOME VEHICLES, DUE TO LANE DEPARTURE WARNING SYSTEM (LDWS) NOT HAVING UPDATED SOFTWARE AND DIAGNOSTIC TROUBLE CODES (DTC) C1702, C221. MODEL 2014 EQUUS. Read More »
-
TSB #14-AT-001
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #13-01-047A
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #13-01-047
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #20-BD-014H
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
-
TSB #24-BD-001H
This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. Read More »
-
TSB #23-BD-002H
This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
-
TSB #19-BE-004H
This bulletin provides information on the serviceable parts for the outside mirror assembly. When diagnosing and repairing the outside mirror, do not replace the entire assembly. Read More »
-
TSB #24-BD-001H
This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. Read More »
-
TSB #19-BE-004H
This bulletin provides information on the serviceable parts for the outside mirror assembly. When diagnosing and repairing the outside mirror, do not replace the entire assembly. Read More »
-
TSB #5NP-X3Q5Y-02
The front seat belt assembly incorporates a seat belt anchor pretensioner fastened to the vehicle?s front seat frame. Read More »
-
TSB #5NP-E3P6N-01
Hyundai Motor America is conducting a Service Campaign to install warning labels on the driver's and/or passenger's seat belt assemblies on 2009-14 Model Year Genesis sedan and 2011-16 Equus vehicles. Read More »
-
TSB #5NP-T4G7K-01
The front seat belt assembly incorporates a seat belt anchor pretensioner fastened to the vehicle's front seat frame. Read More »
-
TSB #23-01-034H
In certain areas, a vehiclea??s underbody may exhibit corrosion due to road-salt usage. As a preventative measure, a cavity wax coating is applied to the internal surfaces of underbody components and an undercoating spray is applied to ... Read More »
-
TSB #23-01-034H
In some areas, a vehiclea??s underbody may exhibit corrosion due to road salt usage. As a preventative measure, cavity wax coating is applied to the internal surfaces of underbody components, and an undercoating spray is applied to the ... Read More »
-
TSB #23-BD-007H
Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. Read More »
-
TSB #14-01-062
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #5NP-J4N8R-01
DO NOT REPLACE THE TRANSMISSION FOR THE DTC LISTED. INSTEAD, FOLLOW THE REPAIR PROCEDURE AND REPLACE THE E-MODULE. Read More »
-
TSB #22-GI-006H
Effective June 2, 2008, Federal Motor Vehicle Safety Standard 110 (FMVSS 110) established a threshold for correcting load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail ... Read More »
-
TSB #20-SS-004H
This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. Read More »
-
TSB #20-SS-002H(1)
This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance. Read More »
-
TSB #20-SS-004H
This bulletin provides tire vibration service procedures, including how to optimize vehicle vibration performance. Read More »
-
TSB #20-SS-002H(1)
This bulletin provides information on tire maintenance best practices and procedures for dealers and customers to maximize tire life and performance. Read More »
-
TSB #19-BE-011H-1
The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. Read More »
-
TSB #19-BE-011H-1
The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. Read More »
-
TSB #14-BE-001
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #21-EM-004H
This bulletin provides the service procedure for engine connecting rod bearing clearance testing. Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required ... Read More »
-
TSB #21-BR-002H
This bulletin provides best practice recommendations when performing brake service procedures. Read More »
-
TSB #21-EM-003H
This bulletin provides the inspection procedure and repair guidelines for certain vehicles listed below. Read More »
-
TSB #20-BD-014H
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
-
TSB #20-BD-007H-1
This bulletin describes the general guidelines to help disinfect and protect vehicle exterior/interior surfaces using recommended safe chemical products. Read More »
-
TSB #20-EE-003H
This bulletin provides information on identifying dealer stock vehicles with either: a?? A Battery SOC alert - low Battery State of Charge (SOC) at or below 50%. a?? A 30 Day alert - vehicle has not started and reported an SOC in 30 days. Read More »
-
TSB #19-AT-021H-1
If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. Read More »
-
TSB #19-AT-007H
This bulletin provides a procedure to transfer oil pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the TCU learning time and improve the shift quality. Read More »
-
TSB #14-01-062
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #13-BE-007
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #5NP-T5L2W-02
Hyundai Motor America is changing the Genesis sedan applicable model years to 2011-14 for service campaign T2R. Read More »
-
TSB #5NP-E3P6N-01
Hyundai Motor America is conducting a Service Campaign to install warning labels on the driver's and/or passenger's seat belt assemblies on 2009-14 Model Year Genesis sedan and 2011-16 Equus vehicles. Read More »
-
TSB #20-AT-016H
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions: Read More »
-
TSB #5NP-J4N8R-01
DO NOT REPLACE THE TRANSMISSION FOR THE DTC LISTED. INSTEAD, FOLLOW THE REPAIR PROCEDURE AND REPLACE THE E-MODULE. Read More »
-
TSB #14-01-035
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #21-BR-002H
This bulletin provides best practice recommendations when performing brake service procedures. Read More »
-
TSB #20-BD-014H
This bulletin provides information regarding condensation related to moisture accumulation in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. Read More »
-
TSB #20-AT-016H
The automatic transmission warranty repair policy authorizes in-dealership repairs of the following components for both OEM (new) and remanufactured automatic transmissions: Read More »
-
TSB #20-BD-007H
This bulletin describes the general guidelines to disinfect and protect vehicle interior surfaces using certain safe chemical products. Read More »
-
TSB #19-GI-006H
This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Read More »
-
TSB #19-GI-006H
This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Read More »