2018 Mazda MAZDA6
TSBs (Technical Service Bulletins)
Technical Service Bulletins (TSBs) for the 2018 MAZDA6 are official communications between Mazda & their dealerships that describe processes for troubleshooting or fixing certain common problems. All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #06-001-24
Some customers may complain about a creaking, knocking, rattle or clunk noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. Read More »
-
TSB #06-004-23b
Some customers may complain about a creaking noise coming from the steering column while driving. A steering column nut loosens due to excessive load when driving on irregular roads. Read More »
-
TSB #06-001-23a
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
-
TSB #02-003-22
Some customers may complain that the steering wheel is off center more than 3??A? even when driving straight on a flat road. Read More »
-
TSB #00-001-22
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #02-003-21-3777
Some customers may complain that the steering wheel is off center more than 3??A? even when driving straight on a flat road. Read More »
-
TSB #00-001-21-3768
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #15-003-20-3737a
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] (Error signal received from electric power steering (EPS) control module) stored in memory. Read More »
-
TSB #06-003-20-3718b
Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. Read More »
-
TSB #06-003-20-3718
Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. Read More »
-
TSB #06-003-20-3718
Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. Read More »
-
TSB #02-003-20-3677
Some customers may complain that the steering wheel is off center more than 3??A? even when driving straight on a flat road. Customers having this concern should have their vehicle repaired using the following repair procedure. Read More »
-
TSB #SA-033-19
Some customers may have a concern of a loose steering wheel. If a customer reports a loose steering wheel and the lock bolt is found to be loose, DO NOT simply re-tighten the steering wheel. Follow the steps below in the Repair Procedure. Read More »
-
TSB #02-004-19-3574
Some customers may complain that the steering wheel is off center more than 3? even when driving straight on a flat road. Read More »
-
TSB #MT-012-18
If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. Read More »
-
TSB #02-010-18-3477
Some customers may complain that the steering wheel is off center more than 3? even when driving straight on a flat road. Read More »
-
TSB #15-003-20-3737
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Read More »
-
TSB #02-004-22a
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #02-002-20-3651
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #02-003-19-3547
Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage. Read More »
-
TSB #02-001-19-3550
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #02-005-18-3444
Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage. Read More »
-
TSB #02-006-18-3449
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #SA-006-22
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #SA-016-19
There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #02-006-18-3449
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #SA-003-23a
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #SA-003/23
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #04-002-21-3809
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
-
TSB #04-007-20-3713a
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
-
TSB #04-002-20-3643b
Some vehicles may exhibit a groan noise from the front brakes when braking at a very low speed (approximately 6 mph/10 km/h). Read More »
-
TSB #15-003-20-3737a
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] (Error signal received from electric power steering (EPS) control module) stored in memory. Read More »
-
TSB #00-002-19-3561
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. Read More »
-
TSB #04-002-19-3545
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #00-003-18-3480
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAOauthorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program. Read More »
-
TSB #04-004-18-3468
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #15-006-17-3388
Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. Read More »
-
TSB #SA-016-24
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-010-23
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #04-003-22a
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
-
TSB #SA-078-22
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #00-001-22
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #04-001-21-3798
Some vehicles may exhibit a groan noise from the front brakes when braking at a very low speed (approximately 6 mph/10 km/h). Read More »
-
TSB #04-007-20-3713
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
-
TSB #15-003-20-3737
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Read More »
-
TSB #00-001-20-3689
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-019-20
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #04-002-20-3643a
Some vehicles may exhibit a groan noise from the front brakes when braking at a very low speed (approximately 6 mph / 10 km/h). Read More »
-
TSB #04-006-19-3643
Some vehicles may exhibit a groan noise from the front brakes when braking at a very low speed (approximately 6 mph / 10 km/h). Read More »
-
TSB #09-010-19-3624
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #15-002-19-3542a
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #00-003-18-3480a
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. Read More »
-
TSB #01-015-18-3513
Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in the PCM memory when engine cranking is interrupted. Read More »
-
TSB #04-001-19-3556
Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. Read More »
-
TSB #SA-055-20a
If a customer comes in with the following concerns: ??A?A? OIL PRESSURE WARNING light and/or the CHECK ENGINE light ON. ??A?A? DTC P055F and/or P0524 stored. ??A?A? No driveability concern or engine mechanical noise. Read More »
-
TSB #04-007-20-3713
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
-
TSB #SA-062-20
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ... Read More »
-
TSB #04-007-20-3713a
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
-
TSB #04-007-20-3713
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
-
TSB #SA-013-22
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #05-003-20-3725
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #SA-022-19
If you receive a customer complain of lack of power, rough idle, engine noise with stored DTC's P0340:00, P0304:00, P3400:00, P349B:00, and/or P3498:00, perform the following. Read More »
-
TSB #SA-015-19a
If you receive a customer concern with the check engine light coming on and DTC P3400 (cylinder deactivation system malfunction) stored, perform the inspection in the Repair Procedure. Read More »
-
TSB #01-011-19-3586
Some customers may experience a check engine light illuminating with DTC P2096:00 stored in PCM memory. DTC P2096:00 - Air fuel too lean. NOTE: This concern occurs only on vehicles with PCMs manufactured by Mitsubishi. Read More »
-
TSB #SA-015-19
If you receive a customer concern with the check engine light coming on and DTC P3400 (cylinder deactivation system malfunction) stored, perform the inspection in the Repair Procedure. Read More »
-
TSB #SA-012-19
On some vehicles, a tapping or knocking noise may be heard from the top end after the engine cools down (vehicle is parked overnight) or it has been idling for an extended time. Read More »
-
TSB #SA-005-19
A tapping/rattling noise may be noticed from the valve train area. This condition usually occurs after the engine has been turned off at normal operating temperature and then not warmed up to full operating temperature during the next ... Read More »
-
TSB #01-003-19-3557
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. Read More »
-
TSB #SA-041-18
If you receive a customer complain of lack of power, rough idle, engine noise with stored DTC's P0340:00, P0304:00, P3400:00, P349B:00, and/or P3498:00, perform the following. Read More »
-
TSB #01-022-18-3528a
Some vehicles may exhibit an excessive body vibration/unusual noise when idling or driving after parking inextremely cold temperatures (-25?C/-13?F). NOTE: This excessive vibration does not occur if the engine mount rubber No. Read More »
-
TSB #09-037-18-3534a
Some vehicles equipped with MAZDA CONNECT may exhibit the following oil maintenance monitor concerns on the center display: The wrench light (Oil Change Due message) cannot be cleared using MAZDA CONNECT/Applications/Vehicle Status ... Read More »
-
TSB #01-015-18-3513a
Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 and U0401:00 stored in the PCM memory when engine cranking is interrupted and on A/T vehicles, DTC U0442:00 is also stored. Read More »
-
TSB #MT-008-18
Some customers may complain about: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator, light flashing, Battery discharge, Electrical relay buzzing noise. Read More »
-
TSB #01-015-18-3513
Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in the PCM memory when engine cranking is interrupted. Read More »
-
TSB #MT-007-18
ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. Read More »
-
TSB #MT-008-18
ENGINE NO START (KEY NOT DETECTED): Some customers may complain about the following: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing. Read More »
-
TSB #01-012-18-3474
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. Read More »
-
TSB #SA-026-18
If a vehicle is driven on extremely short trips most of the time (where the engine never reaches normal operating temperature), the engine oil may become diluted with fuel and the engine oil level will increase. Read More »
-
TSB #MT-021-17
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. Read More »
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #01-005-23a
Some customers may experience the check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up The engine temperature gauge fluctuates The low coolant ... Read More »
-
TSB #SA-081-23
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
-
TSB #SA-032-23a
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #SA-037-23a
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #SA-037-23
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #01-008-23
Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. Read More »
-
TSB #SA-035-23
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
-
TSB #SA-032-23
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #01-006-23
Some vehicles may exhibit oil seepage or oil leak onto the engine front cover, which becomes more apparent with dust adhesion. Read More »
-
TSB #01-005-23
Some customers may experience the check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. Read More »
-
TSB #01-002-23a
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold flange (2) on the cylinder head. Read More »
-
TSB #SA-010-23
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #01-001-23a
Some customers may complain about a poor acceleration and rough idling or the CHECK ENGINE light ON with DTC P0301:00, P0302:00, P0303:00, P0304:00.NOTE: Only turbo engines are applicable; non-turbo engines are NOT applicable. Read More »
-
TSB #01-004-23
Some vehicles may have the check engine light on with DTC P0524:00 or P055F:00 stored in memory. Contamination in the engine oil may cause the engine oil solenoid valve to become stuck, resulting in improper operation of the oil pump and ... Read More »
-
TSB #RF-23-01
When servicing SKYACTIV engine vehicles requiring to replace the Oil Galley Plug and Crush Washer, order the required part numbers below. Read More »
-
TSB #01-002-23
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole or at the outside of the exhaust manifold. Read More »
-
TSB #01-001-23
Some customers may complain about a poor acceleration and rough idling or the CHECK ENGINE light ON with DTC P030X:00 (only turbo engines are applicable; non-turbo engines are NOT applicable). Read More »
-
TSB #MT-004-22
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. Read More »
-
TSB #01-013-22
Some customers may experience the CHECK ENGINE light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: * The engine takes longer to warm up * The engine temperature gauge fluctuates * The low ... Read More »
-
TSB #SA-065-22
Some vehicles equipped with a coolant control valve may exhibit difficulties when refilling the coolant because the control valve is closed and air in the engine cannot escape during ignition ON. Read More »
-
TSB #01-012-22
Some vehicles may exhibit accumulation of dried coolant (1) around the water pipe (2). This is caused by a gap between the housing and pipe due to a press fitting during the manufacturing process. Read More »
-
TSB #01-007-22
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole or at the outside of the exhaust manifold. Read More »
-
TSB #SA-018-22
The WSM shows 3 possible crankshaft sprocket and timing chain combinations (Type A, B and C), but some vehicles have been produced with a combination of Type A timing chain with 2 yellow-colored links with a Type B crankshaft sprocket. Read More »
-
TSB #00-001-22
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-031-21c
New Cylinder Head Assembly Established: A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #01-013-21-3753a
Coolant Leaks At Cylinder Head: Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold (2). Read More »
-
TSB #01-014-21-3840
Some vehicles may exhibit the CHECK ENGINE light on with DTC P011B:00 (Engine coolant temperature/IAT: Correlation error) when using an engine block heater which is set up by MCI as local accessory parts. Read More »
-
TSB #SA-031-21c
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #SA-031-21b
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #MT-002-21
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. Read More »
-
TSB #SA-047-21
If you receive a customer concern about the CHECK ENGINE light coming on and DTC P3400 (cylinder deactivation system malfunction) stored, the cylinder deactivation oil control valve may be plugged with plastic debris from the oil filter ... Read More »
-
TSB #07-003-21-3825
Some vehicles may exhibit a squeaking noise from the blower motor while it is operating. This is caused by burrs that were not trimmed completely in the manufacturing process of the blower motor. Read More »
-
TSB #01-006-21-3779a
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #01-001-21-3761a
Some vehicles may exhibit an occasional rough idle accompanied with DTC P0300:00 (Random misfire) due to the following: 1. While closing the EGR valve, carbon deposit etc. Read More »
-
TSB #MT-002-21
When programming a key or installing a Genuine Mazda Accessory Remote Engine Start system, you may encounter programming difficulty. Read More »
-
TSB #SA-031-21
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #MT-001-21
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #01-002-21-3767a
Some vehicle may exhibit a tapping noise from the engine during idling; etc., and synchronized to the engine rpm. Read More »
-
TSB #01-004-21-3773a
Some vehicles may have the check engine light on with DTC P0524:00 or P055F:00 stored in memory. Contamination in the engine oil may cause the engine oil solenoid valve to become stuck, resulting in improper operation of the oil pump and ... Read More »
-
TSB #SA-017-21a
CHECK ENGINE LIGHT ON WITH DTC P0126:00 AND ENGINE RUNNING COOLER THAN NORMAL / POOR HEATER PERFORMANCE / LOW ENGINE COOLANT TEMPERATURE (BLUE) LIGHT ON: Some customers may experience the CHECK ENGINE LIGHT ON with DTC P0126:00 ... Read More »
-
TSB #SA-017-21
Some customers may experience the CHECK ENGINE LIGHT ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. Read More »
-
TSB #CSP05c
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
-
TSB #CSP05d
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
-
TSB #01-003-21-3776
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. Read More »
-
TSB #00-001-21-3768
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #CSP05b
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #01-001-21-3761
Some vehicles may exhibit an occasional rough idle accompanied with DTC P0300:00 (Random misfire) due to the following: 1. While closing the EGR valve, carbon deposit etc. Read More »
-
TSB #01-002-21-3767
Some vehicle may exhibit a tapping noise from the engine during idling; etc., and synchronized to the engine rpm. Read More »
-
TSB #SA-058-20c
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #SA-035-20b
Some customers may experience the CHECK ENGINE LIGHT ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. Read More »
-
TSB #CSP05a
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #MT-005-20
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Read More »
-
TSB #CSP05
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #01-006-20-3695b
Some vehicle may exhibit a tapping noise from the engine during idling; etc., and synchronized to the engine rpm. Read More »
-
TSB #SA-071-20
Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. Read More »
-
TSB #01-012-20-3738
Some vehicles may experience the check engine light on with DTCs P2096:00, P2097:00 and/or P0524:00 that cannot be cleared by itself, and the check engine light stays on even if the detection condition has gone. Read More »
-
TSB #SA-061-20a
If you receive a customer concern about the CHECK IN light coming on and DTC P3400 (cylinder deactivation system malfunction) stored, the cylinder deactivation oil control valve may be plugged with plastic debris from the oil filter ... Read More »
-
TSB #SA-058-20a
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #SA-061-20
If you receive a customer concern about the CHECK IN light coming on and DTC P3400 (cylinder deactivation system malfunction) stored, perform the inspection in the Repair Procedure. Read More »
-
TSB #SA-058-20
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #SA-055-20a
If a customer comes in with the following concerns: ??A?A? OIL PRESSURE WARNING light and/or the CHECK ENGINE light ON. ??A?A? DTC P055F and/or P0524 stored. ??A?A? No driveability concern or engine mechanical noise. Read More »
-
TSB #SA-055-20
If a customer comes in with the following concerns, perform the inspection procedure. ??A?A? OIL PRESSURE WARNING light and/or the CHECK ENGINE light ON. ??A?A? DTC P055F and/or P0524 stored. Read More »
-
TSB #01-008-20-3694
Some customers may experience the CHECK ENGINE light ON with DTC P2229:00 stored in PCM memory. ??A?A? P2229:00 (BARO sensor circuit high input). Read More »
-
TSB #01-006-20-3695
Some vehicle may exhibit a tapping noise from the engine during idling; etc., and synchronized to the engine rpm. Read More »
-
TSB #SA-025-20a
A valve tapping or knocking noise may be heard from the top end after the engine cools down (the vehicle is parked overnight) or after it has been idling for an extended time. Read More »
-
TSB #00-001-20-3689
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-035-20a
Some customers may experience the CHECK ENGINE LIGHT ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: ??A?A? The engine takes longer to warm up. ??A?A? The engine temperature gauge fluctuates. Read More »
-
TSB #SA-035-20
Some customers may experience the CHECK ENGINE LIGHT ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. Read More »
-
TSB #SA-025-20
A valve tapping or knocking noise may be heard from the top end after the engine cools down (the vehicle is parked overnight) or after it has been idling for an extended time. Read More »
-
TSB #SA-009-20
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. Read More »
-
TSB #MT-002-19
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
-
TSB #01-023-19-3648
Some vehicles may exhibit engine overheating with one or more of the following symptoms: ??A?A? ??A?A?EXCESSIVE ENGINE TEMPERATURE: ENGINE OUTPUT WILL BE LIMITED??A?A? displayed in the instrument cluster ??A?A? Red overheating indicator ... Read More »
-
TSB #01-022-19-3657
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
-
TSB #SA-053-19
GUIDE LINES AND PHOTOS TO DETERMINE IF FLUID/OIL SEEPAGE OR LEAK IS SEVERE ENOUGH TO REQUIRE WARRANTY REPAIR OR TO CLEAN AND MONITOR. Read More »
-
TSB #01-019-19-3628
Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. Read More »
-
TSB #SA-049-19
Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint: ??A?A? MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE ??A?A? CANNOT COMMUNICATE WITH ... Read More »
-
TSB #MT-004-19
Some customers may complain about: ??A?A? Intermittent engine no start ??A?A? Instrument cluster red security indicator light ON ??A?A? Engine Start/Start Button Amber indicator light flashing ??A?A? Battery discharge ??A?A? Electrical ... Read More »
-
TSB #MT-003-19
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Read More »
-
TSB #MT-002-19
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
-
TSB #SA-041-19
If a customer comes in with the following concerns, contact Hotline for assistance. OIL PRESSURE WARNING light and/or the CHECK ENGINE light ON, DTC P055F and/or P0524 stored, No drivability concern or engine mechanical noise, Outside the ... Read More »
-
TSB #SA-040-19
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
-
TSB #01-015-19-3626
Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). Read More »
-
TSB #SA-012-19
On some vehicles, a tapping or knocking noise may be heard from the top end after the engine cools down (vehicle is parked overnight) or after it has been idling for an extended time. Read More »
-
TSB #01-014-19-3618
Some customers may experience a check engine light illuminating with DTC P0012:00 stored in PCM memory. DTC P0012:00 - Electric variable valve timing control system: Over-retarded. Read More »
-
TSB #SA-030-19
While inspecting turbocharger housings, you may see cracks (fractures) as shown below. The cracks do not affect engine performance or cause any noise, so replacement is NOT necessary. Read More »
-
TSB #00-003-19-3583
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
-
TSB #01-005-19-3548
Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak). Read More »
-
TSB #01-004-19-3558
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Read More »
-
TSB #SA-029-18
IMPORTANT: If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Read More »
-
TSB #05-004-18-3466
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. Read More »
-
TSB #04-003-18-3455
Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. Read More »
-
TSB #SA-030-19
While inspecting turbocharger housings, you may see cracks (fractures) as shown below. The cracks do not affect engine performance or cause any noise, so replacement is NOT necessary. Read More »
-
TSB #01-002-23a
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold flange (2) on the cylinder head. Read More »
-
TSB #01-002-23
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole or at the outside of the exhaust manifold. Read More »
-
TSB #SA-031-21a
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #01-016-18-3522
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Read More »
-
TSB #01-013-18-3478
Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak)The concern is most likely the result of the customer not getting the fuel cap completely ... Read More »
-
TSB #01-005-18-3415
Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. Read More »
-
TSB #01-013-21-3753
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold (2). Read More »
-
TSB #MT-002-19
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
-
TSB #MT-002-21a
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. Read More »
-
TSB #00-003-19-3583
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
-
TSB #01-005-18-3415
Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. Read More »
-
TSB #00-003-19-3583
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
-
TSB #MT-002-21a
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. Read More »
-
TSB #RF-16-03R1
The SKYACTIV?-G 2.5T engine requires a unique oil filter (PY8W-14-302) which is NOT interchangeable with other SKYACTIV? oil filters. The unique oil filter can be identified with two white bands as shown below. Read More »
-
TSB #PF-24-03
Due to limitations, certain vehicles from 2016 to current models might display an inaccurate transmission part number in the Global Electronic Parts Catalog (GEPC). Read More »
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #05-005-23a
Some vehicles may exhibit a chirp noise (stick-slip noise) from the automatic transaxle (AT) when shifting from 3 to 4 while driving. Read More »
-
TSB #05-005-23
Some vehicles may exhibit a chirp noise (stick-slip noise) from the automatic transaxle (AT) when shifting from 3 to 4 while driving. Read More »
-
TSB #05-003-23
Some customers may complain of a shift shock felt when shifting into 3rd, 5th and/or R range with no A/T related DTC stored. Read More »
-
TSB #05-002-23
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #SA-068-22
The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. Read More »
-
TSB #01-010-22
Some customers may experience a squeaking noise may be heard from the exhaust manifold when the idle speed drops from fast idle to normal idle speed during cold start. This is caused by a variable valve being stuck in the closed position. Read More »
-
TSB #SA-038-22
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. Read More »
-
TSB #05-001-22
Some customers may complain of a shift shock felt when shifting into 3rd, 5th and/or R range with no A/T related DTC stored. Read More »
-
TSB #SA-006-22a
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #SA-006-22
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #00-001-22
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-031-21c
New Cylinder Head Assembly Established: A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #SA-031-21b
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #05-001-21-3826
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. Read More »
-
TSB #SA-032-21
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #01-008-21-3787
Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). Read More »
-
TSB #00-001-21-3768
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #05-005-20-3752
Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. Read More »
-
TSB #SSPC0
SSPC0 - CALIFORNIA REGISTERED VEHICLES DIAGNOSTIC TROUBLE CODES (DTC) CONCERN: Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2019 CX-3, Mazda3 and MX-5 as well as 2018 Mazda6 vehicles and ... Read More »
-
TSB #05-003-20-3725
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #SA-053-20
When replacing manual or automatic transmission, make sure to remove the plug from the old transmission (as shown below) and then re-install it to the new transmission with a new washer. Read More »
-
TSB #01-008-20-3694
Some customers may experience the CHECK ENGINE light ON with DTC P2229:00 stored in PCM memory. ??A?A? P2229:00 (BARO sensor circuit high input). Read More »
-
TSB #SA-025-20a
A valve tapping or knocking noise may be heard from the top end after the engine cools down (the vehicle is parked overnight) or after it has been idling for an extended time. Read More »
-
TSB #00-001-20-3689
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-030-20
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. NOTE: The following Caution is included with every ATX that requires configuration. Read More »
-
TSB #SA-058-19
WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the ... Read More »
-
TSB #SA-053-19
GUIDE LINES AND PHOTOS TO DETERMINE IF FLUID/OIL SEEPAGE OR LEAK IS SEVERE ENOUGH TO REQUIRE WARRANTY REPAIR OR TO CLEAN AND MONITOR. Read More »
-
TSB #05-004-19-3466
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. Read More »
-
TSB #SA-015-19a
If you receive a customer concern with the check engine light coming on and DTC P3400 (cylinder deactivation system malfunction) stored, perform the inspection in the Repair Procedure. Read More »
-
TSB #05-002-19-3576
Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. Read More »
-
TSB #05-002-18-3454
The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use"ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. Read More »
-
TSB #05-001-20-3699
Some customers may complain of a shift shock felt when shifting into 3rd, 5th and/or R range with no A/T related DTC stored. Read More »
-
TSB #05-002-23
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #SA-038-22
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. Read More »
-
TSB #01-015-18-3513
Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in the PCM memory when engine cranking is interrupted. Read More »
-
TSB #SA-038-22
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. Read More »
-
TSB #03-002-18-3505a
Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. Read More »
-
TSB #03-001-19-3505b
Some vehicles may exhibit a squeak noise from the right front driveshaft at the automatic transaxle when driving. Read More »
-
TSB #03-002-18-3505a
Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. Read More »
-
TSB #03-002-18-3505
Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. Read More »
-
TSB #05-002-19-3576
Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. Read More »
-
TSB #SA-037-18
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. Read More »
-
TSB #07-003-24
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10 A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
-
TSB #SA-008-24
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #01-007-23a
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #SA-032-23a
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #SA-032-23
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #SA-033-23
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #01-007-23
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #09-016-23
Speedometer replacement procedure Read More »
-
TSB #SA-010-23
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #09-008-23
Some vehicles may experience the seat ventilation system still on after the engine has been turned off, in some cases this causes the battery to be completely discharged and not rechargeable. Read More »
-
TSB #07-002-23
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
-
TSB #09-018-22b
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.324 or later). The system performance has been improved as follows: Ver. 74.00. Read More »
-
TSB #SA-041-22c
Some customers may complain about infotainment center display: * Ghost Touch * DTC B108E:04 may be stored (Touch screen operates by itself) * Surface Peeling * DTC B108E:04 may be stored * Spider Cracks * White ... Read More »
-
TSB #09-021-22a
Some vehicles may exhibit a malfunction where the touch screen operates by itself (ghost touch). An example ghost touch would be the map on the center display scrolls without touching it. Read More »
-
TSB #22-01R
Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors. Read More »
-
TSB #SA-075-22
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #SA-074-22
Some customers may complain the HVAC system not maintaining the correct temperature or the ambient (outside) temperature reading incorrectly. This is caused by a failure in the ambient temperature sensor. Read More »
-
TSB #SA-066-22
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: * C1001:92 - Forward sensing camera (FSC) poor field of ... Read More »
-
TSB #SA-067-22
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: * ... Read More »
-
TSB #09-032-22a
Some vehicles may experience the seat ventilation system still on after the engine has been turned off, in some cases this causes the battery to be completely discharged and not rechargeable. Read More »
-
TSB #RF-22-01
Some customers may complain about infotainment center display ghost touch (touch screen operates by itself), surface peeling or spider cracks. Repair kits are available to replace just the screen. Read More »
-
TSB #SA-041-22c
Some customers may complain about infotainment center display: - Ghost Touch (Touch screen operates by itself) - Spider Cracks - Surface Peeling - White dots Read More »
-
TSB #09-032-22
Some vehicles may experience the seat ventilation system still on after the engine has been turned off, in some cases this causes the battery to be completely discharged and not rechargeable. Read More »
-
TSB #SA-041-22
Some customers may complain about infotainment center display: - Ghost Touch (Touch screen operates by itself) - Surface Peeling - Spider Cracks Repair kits are available to replace just the screen. Read More »
-
TSB #SA-001-22d
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #01-008-22
Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). Read More »
-
TSB #01-006-22
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #09-018-22
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.311 or later). Read More »
-
TSB #SA-001-22c
Use the symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-026-22
Apple CarPlay / Android Auto Frequently Asked Questions (FAQs) Read More »
-
TSB #SA-001-22c
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #01-003/22
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #SA-001-22
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-001/22
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
-
TSB #01-006-21-3779b
Battery Maintenance: This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #09-037-21-3839
NOTE: These vehicles are orginally built with the center display GML8-611J0* and are not applicable to this TSB. Read More »
-
TSB #SA-052-21
For improvement of electrical diagnosis, the SKYACTIV??A? Wiring Terminal Test Kits has been delivered all the dealers. Read More »
-
TSB #SA-019-21d
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-046-21
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #15-002-21-3812
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #SA-019-21a
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-029-21a
APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
-
TSB #MT-002-21
When programming a key or installing a Genuine Mazda Accessory Remote Engine Start system, you may encounter programming difficulty. Read More »
-
TSB #MT-001-21
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #MT-001-21
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #01-005-21-3778
The Mazda DCA-8000PM is required for all warranty battery testing. If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #01-006-21-3779
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #01-003-21-3776
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. Read More »
-
TSB #09-002-21-3770
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer Read More »
-
TSB #SA-058-20c
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #MT-006-20
Some customers may complain about the following MAZDA CONNECT??A?A? Temperature Warning message: ??A?A? Display is too Hot. Screen performance may be decreased until it cools. Read More »
-
TSB #09-036-20-3756
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH??A? hands-free unit or text messaging related concerns. Read More »
-
TSB #SA-070-20
APPLE CARPLAY / ANDROID AUTO FREQUENTLY ASKED QUESTIONS (FAQ): NOTE: The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
-
TSB #15-003-20-3737a
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] (Error signal received from electric power steering (EPS) control module) stored in memory. Read More »
-
TSB #SA-063-20
When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage. Read More »
-
TSB #06-003-20-3718
Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. Read More »
-
TSB #MT-001-20
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #SA-041-20
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #SA-011-20a
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
-
TSB #SA-025-20
A valve tapping or knocking noise may be heard from the top end after the engine cools down (the vehicle is parked overnight) or after it has been idling for an extended time. Read More »
-
TSB #01-002-20-3678
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. Read More »
-
TSB #SA-009-20
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. Read More »
-
TSB #SA-011-20
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
-
TSB #09-003-20-3671
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #SA-049-19
Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint: ??A?A? MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE ??A?A? CANNOT COMMUNICATE WITH ... Read More »
-
TSB #MT-004-19
Some customers may complain about: ??A?A? Intermittent engine no start ??A?A? Instrument cluster red security indicator light ON ??A?A? Engine Start/Start Button Amber indicator light flashing ??A?A? Battery discharge ??A?A? Electrical ... Read More »
-
TSB #15-004-19-3639
Some customer's may complain that In heavy rain, the front parking sensor system detects objects despite nothing being in front of the vehicle, and no related DTCs are stored. Read More »
-
TSB #09-010-19-3624
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #09-031-19-3625
After the installation of a new instrument cluster, the message "Fctry" or ??A???A???A?Factory??A???A???A? is displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Read More »
-
TSB #SA-031-19
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #SA-029-19
Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. Read More »
-
TSB #09-022-19-3599
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #SA-006-19a
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #SA-001-19b
APPLE CARPLAY??A?A? / ANDROID AUTO??A?A? FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #SA-001-19a
APPLE CARPLAY??A?A? / ANDROID AUTO??A?A? FREQUENTLY ASKED QUESTIONS (FAQ). Many frequently asked question and the answers. Read More »
-
TSB #05-001-19-3538
When pressing the START/STOP button in very cold weather, the ignition may not turn off on some vehicles equipped with a lock release button (1) on the selector lever knob. Read More »
-
TSB #09-010-19-3577
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #15-002-19-3542
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #SA-006-19
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #01-006-19-3549
The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazda models, there is no key cylinder on the steering column. Read More »
-
TSB #01-001-19-3551
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #01-002-19-3552
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #SA-047-18
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #15-002-18-3502a
Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. Read More »
-
TSB #MT-002-18
Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth? and the same device is also connected to the USB port for charging. Read More »
-
TSB #MT-010-18
Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. Read More »
-
TSB #MT-011-18
SMS (Short Message Service) messages received by paired phones (Android and iPhone 5 iOS 7.0 or higher) can be downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. Read More »
-
TSB #MT-010-18
Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. Read More »
-
TSB #09-037-18-3534a
Some vehicles equipped with MAZDA CONNECT may exhibit the following oil maintenance monitor concerns on the center display: The wrench light (Oil Change Due message) cannot be cleared using MAZDA CONNECT/Applications/Vehicle Status ... Read More »
-
TSB #SA-045-18
For improvement of electrical diagnosis, the SKYACTIV? Wiring Terminal Test Kits has been delivered all the dealers. Read More »
-
TSB #MT-004-18
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #MT-007-18
Some customers may complain about the following: Engine no start. A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g. Read More »
-
TSB #MT-008-18
Some customers may complain about: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator, light flashing, Battery discharge, Electrical relay buzzing noise. Read More »
-
TSB #09-035-18-3509
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #SA-036-18
MAZDA MOBILE START (MMS) APP ERROR MESSAGE INSTALLED ON ANDROID DEVICES: Customers may get an error message "Device no longer has access or service." for the MMS APP installed on android devices starting 8/1/18. Read More »
-
TSB #MT-004-18
ELECTRICAL CONCERN AND/OR MULTIPLE DTC'S DUE TO AFTERMARKET DEVICE: If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored... Read More »
-
TSB #MT-007-18
ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. Read More »
-
TSB #15-002-18-3502
Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. Read More »
-
TSB #09-010-18-3440a
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.546 or later). NOTE: For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #SA-025-18
When performing the MGSS Workshop Manual 360? View Monitor System Aiming Procedure, M-MDS may show error message "Procedure unsuccessful". This may be caused by light glare on the SST. Read More »
-
TSB #SA-021-18
MAZDA CONNECT SOFTWARE VERSION 59.00.545 AVAILABLE. An update to the MAZDA CONNECT system is now available for download from the Mazda Global Service Support (MGSS) system. The new version number is 59.00.545. Read More »
-
TSB #MT-004-18
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
-
TSB #MT-002-18
Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth? and the same device is also connected to the USB port for charging. Read More »
-
TSB #MT-001-18
When installing a navigation SD card, the center display may show error message "Invalid SD Card". This may be caused by: The navigation SD card lock tab is locked.The navigation SD card has a VIN mismatch due to SD card swapping. Read More »
-
TSB #15-005-17-3358b
Some customers may complain that the BSM indicator light on the outer mirror glass does not illuminate when: ? Customer vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area. Read More »
-
TSB #15-005-17-3358a
Some customers may complain that when passing a vehicle slowly, even if the vehicle is still in the alert area, the BSM indicator light on the outer mirror glass does not illuminate. Read More »
-
TSB #15-006-17-3388
Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. Read More »
-
TSB #SA266
MAZDA Mobile start (MMS) cannot communicate with vehicle Read More »
-
TSB #01-007-23
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #01-006-21-3779a
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #15-003-20-3737
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Read More »
-
TSB #MT-004-18
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #MT-008-18
Some customers may complain about: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator, light flashing, Battery discharge, Electrical relay buzzing noise. Read More »
-
TSB #01-008-18-3451
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #01-009-18-3452
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #05-001-19-3538
When pressing the START/STOP button in very cold weather, the ignition may not turn off on some vehicles equipped with a lock release button (1) on the selector lever knob. Read More »
-
TSB #SA-050-23
Some customers may complain about scratches on the instrument cluster lens. Read More »
-
TSB #07-002-23
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
-
TSB #SA-039-22
Some customers may complain about scratches on the instrument cluster lens. Read More »
-
TSB #09-009-19-3566
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #09-002-18-3410
After the installation of a new instrument cluster, the message "Fctry" or "Factory" is displayed instead ofthe odometer. This concern may also occur when a room fuse is installed in a new vehicle. Read More »
-
TSB #09-035-17-3080
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #SA-061-17
In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is? 2017 Mazda North American Operations, U.S.A. Read More »
-
TSB #09-016-23
Speedometer replacement procedure Read More »
-
TSB #09-024-22
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. Read More »
-
TSB #SA-001-22b
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-001/22
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
-
TSB #09-021-21-3818b
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #09-030-20-3740
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #09-022-19-3599a
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #01-023-19-3648
Some vehicles may exhibit engine overheating with one or more of the following symptoms: ??A?A? ??A?A?EXCESSIVE ENGINE TEMPERATURE: ENGINE OUTPUT WILL BE LIMITED??A?A? displayed in the instrument cluster ??A?A? Red overheating indicator ... Read More »
-
TSB #SA-047-18
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #SA-025-18
When performing the MGSS Workshop Manual 360? View Monitor System Aiming Procedure, M-MDS may show error message "Procedure unsuccessful". This may be caused by light glare on the SST. Read More »
-
TSB #SA-017-18
Upgrade your PCs to IDS version 109.00 and 109.01 from the previous version. NOTE: You may see ?Selection not available? on IDS when a selecting ?Programming menu?, 108. Read More »
-
TSB #09-010-18-3440
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.504 or later). NOTE: For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #DRW13
Dealer Rework (DRW) 13 ? Mazda Connect Navigation Concern 2018MY CX-5, CX-3, CX-9, Mazda6, Mazda 3 and MX-5: We write to inform you that certain vehicles are affected by the concern mentioned below. Read More »
-
TSB #SA-012-18
Some 2018 vehicles built after January 1, 2018 and equipped with Navigation may exhibit one of these concerns after the user inputs an address: A screen pops up that says "House number not found. Read More »
-
TSB #01-014-21-3840
Some vehicles may exhibit the CHECK ENGINE light on with DTC P011B:00 (Engine coolant temperature/IAT: Correlation error) when using an engine block heater which is set up by MCI as local accessory parts. Read More »
-
TSB #SA-022-21
When performing the MGSS Workshop Manual 360??A? View Monitor System Aiming Procedure, M-MDS may show error message "Procedure unsuccessful". This may be caused by light glare on the SST. Read More »
-
TSB #SA-010-23
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #09-007/22
Some vehicles may exhibit a white powdery dust (1) adhering to the inner surface of the headlight lens causing a poor appearance. Read More »
-
TSB #SA-036-21
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
-
TSB #09-010-19-3624
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #15-002-19-3542a
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #09-003-19-3555a
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #09-003-19-3555
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #15-005-17-3358b
Some customers may complain that the BSM indicator light on the outer mirror glass does not illuminate when: ? Customer vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area. Read More »
-
TSB #09-003-19-3555a
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #09-011-18-3448
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #SA-023-18
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
-
TSB #09-003-19-3555a
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #09-011-18-3448
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #SA-012-23
Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet. Read More »
-
TSB #SA-010-23
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #SA-022-21
When performing the MGSS Workshop Manual 360??A? View Monitor System Aiming Procedure, M-MDS may show error message "Procedure unsuccessful". This may be caused by light glare on the SST. Read More »
-
TSB #15-003-20-3737
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Read More »
-
TSB #SA-062-20
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ... Read More »
-
TSB #SA-027-19
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
-
TSB #09-010-19-3624
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #15-005-17-3358a
Some customers may complain that when passing a vehicle slowly, even if the vehicle is still in the alert area, the BSM indicator light on the outer mirror glass does not illuminate. Read More »
-
TSB #SA-039-23a
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #SA-040-21
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #MT-003-21
Some vehicles may experience exterior trim heat damage when parked near a glass building. This may be caused by the suns reflection. Read More »
-
TSB #MT-007-18
ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. Read More »
-
TSB #SA-012-23
Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet. Read More »
-
TSB #SA-074-22
Some customers may complain the HVAC system not maintaining the correct temperature or the ambient (outside) temperature reading incorrectly. This is caused by a failure in the ambient temperature sensor. Read More »
-
TSB #SA-042-21
Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc. Read More »
-
TSB #08-001-19-3544
This information is provided to help address Passenger Airbag Deactivation (PAD) Indicator illumination concerns during vehicle service. Read More »
-
TSB #08-001-18-3457
This information is provided to help address Passenger Airbag Deactivation (PAD) Indicator illumination concerns during vehicle service. Read More »
-
TSB #MT-003-18
The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles. Read More »
-
TSB #SA-027-18
Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc. Read More »
-
TSB #SA-027-18
Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc. Read More »
-
TSB #SA-039-23a
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #SA-039-23
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #SA-036-23
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the ... Read More »
-
TSB #09-006-23
When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #SA-008-22a
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #09-017-22a
Some vehicles may have rust on the contact parts between the clips (for attaching the roof molding) and the roof panel (ditches of the roof rail). Read More »
-
TSB #SA-008-22
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #MT-001-22
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Read More »
-
TSB #09-004-21-3772
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #SA-009-20
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. Read More »
-
TSB #09-008-19-3565
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #09-014-18-3443a
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #09-021-18-3459a
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #09-014-18-3443
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #09-003-21-3771
When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #09-008-20-3675
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #MT-012-18
If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. Read More »
-
TSB #09-021-18-3459
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #SA-040-19
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
-
TSB #SA-024-18
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
-
TSB #09-021-18-3459
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #09-021-18-3459
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #09-002-21-3770
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer Read More »
-
TSB #09-034-18-3430a
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #09-034-18-3430
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #MT-002-20
New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010. Read More »
-
TSB #MT-010-18
Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. Read More »
-
TSB #SA-022-24
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-031-23
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #SA-006-22a
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #02-002-21-3769a
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #00-001-21-3768
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #02-002-21-3769
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #MT-002-20
New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010. Read More »
-
TSB #02-004-20-3685
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #02-007-19-3645
Some vehicles may exhibit corrosion of the wheel nuts. This is caused by torsional stress concentrating on the tip of the wheel nut because of the thin and long shape of the nut, which damages the coating and causes the corrosion. Read More »
-
TSB #RF-18-02R3
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. Read More »
-
TSB #SA-016-19
There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #RF-18-02R2
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. Read More »
-
TSB #02-002-19-3546
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #SA-002-19
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. Read More »
-
TSB #SA-028-18
Some vehicles with accessory installed wheel locks may have had the wrong kit installed using a 21 mm wheel lock key. As of May 01, 2018, Japan produced vehicles use 17 mm hex lug nuts instead of 21 mm on the same size thread. Read More »
-
TSB #02-008-18-3467
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #RF-18-02R1
As of May 1, 2018, Japan produced vehicles use 17 mm hex lug nuts instead of 21 mm on the same size thread. Read More »
-
TSB #RF-18-02R2
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. Read More »
-
TSB #SA-028-18
Some vehicles with accessory installed wheel locks may have had the wrong kit installed using a 21 mm wheel lock key. As of May 01, 2018, Japan produced vehicles use 17 mm hex lug nuts instead of 21 mm on the same size thread. Read More »
-
TSB #SA-027-19
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
-
TSB #09-008-23
Some vehicles may experience the seat ventilation system still on after the engine has been turned off, in some cases this causes the battery to be completely discharged and not rechargeable. Read More »
-
TSB #09-024-21-3822
Some vehicles may exhibit a breakage of the decoration plate (1) on the front or rear seat backs. This is caused by the seat back decoration plate not being strong enough. Read More »
-
TSB #SA-007-21
Some customers may complain that their seat warmers or seat ventilation do not turn on when the engine is restarted after being left on when turning off the engine. Read More »
-
TSB #09-007-20-3674a
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Read More »
-
TSB #SA-020-20
Due to a vehicle side logic change for the vehicles listed above, the seat warming and seat ventilation systems will no longer automatically turn on when the vehicle is started using the MMS accessory. Read More »
-
TSB #SA-016-20
Some customers may complain that their seat warmers or seat ventilation do not turn on when the engine is restarted after being left on when turning off the engine. Read More »
-
TSB #09-007-20-3674
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Read More »
-
TSB #SA-008-19
Some customers may complain that their seat warmers do not turn on when the engine is restarted after being left on when turning off the engine. Read More »
-
TSB #09-006-19-3563
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Read More »
-
TSB #09-015-18-3445a
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Read More »
-
TSB #09-015-18-3445
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Read More »
-
TSB #SA-020-20
Due to a vehicle side logic change for the vehicles listed above, the seat warming and seat ventilation systems will no longer automatically turn on when the vehicle is started using the MMS accessory. Read More »
-
TSB #SA-008-19
Some customers may complain that their seat warmers do not turn on when the engine is restarted after being left on when turning off the engine. Read More »
-
TSB #15-004-21-3835
NOTE: This Service Information is only applicable for vehicles equipped with a Forward Sensing Camera (FSC), KDD1-67-XCX and GSH7-67-XCX*. Read More »
-
TSB #SA-036-21
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
-
TSB #15-003-20-3737a
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] (Error signal received from electric power steering (EPS) control module) stored in memory. Read More »
-
TSB #SA-062-20
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ... Read More »
-
TSB #SA-003-19
Some vehicles may have one of the following DTCs stored in memory: C1001:92 - Forward sensing camera (FSC) poor field of view. B14F0:92 - General temporary failure in forward sensing camera (FSC). Read More »
-
TSB #15-002-19-3542a
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #SA-037-20
Some vehicles may have one of the following DTCs stored in memory: ??A?A? C1001:92 - Forward sensing camera (FSC) poor field of view ??A?A? B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set ... Read More »
-
TSB #15-004-19-3639
Some customer's may complain that In heavy rain, the front parking sensor system detects objects despite nothing being in front of the vehicle, and no related DTCs are stored. Read More »
-
TSB #SA-003-19
Some vehicles may have one of the following DTCs stored in memory: C1001:92 - Forward sensing camera (FSC) poor field of view. B14F0:92 - General temporary failure in forward sensing camera (FSC). Read More »
-
TSB #SA-003-19
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
-
TSB #15-002-18-3502
Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. Read More »
-
TSB #SA-014-18
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: The ... Read More »
-
TSB #SA-036-21
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
-
TSB #15-002-19-3542a
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #SA-023-18
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
-
TSB #00-002-18-3463a
In support of the new Mazda6 Signature model, Mazda will ship to dealers a new Special Service Tool (SST) to allow for the aiming of the 360 Degree Camera System. Read More »
-
TSB #SA-001/22
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
-
TSB #15-004-19-3639
Some customer's may complain that In heavy rain, the front parking sensor system detects objects despite nothing being in front of the vehicle, and no related DTCs are stored. Read More »
-
TSB #09-033-19-3590
Some vehicles may exhibit the rear parking sensor beeping without any obstacles behind it when the shift lever is shifted into Reverse. This concern only occurs when the rear USB power outlet (1) is broken. Read More »
-
TSB #SA-018-19
Due to a changes in the 2018 Mazda6, there are two things to note of when installing the Rear Parking Sensors. 1. When securing the main harness in step 4, DO NOT attach the one tie wrap as shown. Read More »
-
TSB #SA-006-19a
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #15-006-17-3388
Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. Read More »
-
TSB #SA-001-22c
Use the symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-008-24
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #01-007-23a
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #SA-036-23
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the ... Read More »
-
TSB #RF-22-01R3
This Parts Flash replaces RF-22-01R2 released January 04, 2022. It includes new display repair kit part numbers for the 2018-2019 Mazda2, 2018-2020 CX-3 and 2018-2020 MX-5. Repair kits are available to replace just the screen. Read More »
-
TSB #SA-001-23a
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: ... Read More »
-
TSB #RF-22-01R2
This Parts Flash replaces RF-22-01R released November 21, 2022. It includes a new display repair kit part number for the 2020-2022 MX-5. Repair kits are available to replace just the screen. Read More »
-
TSB #SA-001-23
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: ... Read More »
-
TSB #SA-016-22a
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method Read More »
-
TSB #SA-041-22
Some customers may complain about infotainment center display: Ghost touch, surface peeling, spider cracks. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit. Read More »
-
TSB #SA-039-22
Some customers may complain about scratches on the instrument cluster lens. Read More »
-
TSB #09-017-22a
Some vehicles may have rust on the contact parts between the clips (for attaching the roof molding) and the roof panel (ditches of the roof rail). Read More »
-
TSB #09-021-22
Some vehicles may exhibit a malfunction where the touch screen operates by itself (ghost touch). An example ghost touch would be the map on the center display scrolls without touching it. Read More »
-
TSB #SA-026-22
Apple CarPlay / Android Auto Frequently Asked Questions (FAQs) Read More »
-
TSB #SA-016-22
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method Read More »
-
TSB #09-007/22
Some vehicles may exhibit a white powdery dust (1) adhering to the inner surface of the headlight lens causing a poor appearance. Read More »
-
TSB #SA-001/22
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
-
TSB #09-037-21-3839
NOTE: These vehicles are orginally built with the center display GML8-611J0* and are not applicable to this TSB. Read More »
-
TSB #SA-019-21e
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns Read More »
-
TSB #SA-052-21
For improvement of electrical diagnosis, the SKYACTIV??A? Wiring Terminal Test Kits has been delivered all the dealers. Read More »
-
TSB #01-013-21-3753
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold (2). Read More »
-
TSB #SA-031-21c
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #SA-031-21b
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #SA-019-21d
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #MT-002-21
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. Read More »
-
TSB #09-021-21-3818b
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #07-003-21-3825
Some vehicles may exhibit a squeaking noise from the blower motor while it is operating. This is caused by burrs that were not trimmed completely in the manufacturing process of the blower motor. Read More »
-
TSB #09-025-21-3824
This service bulletin provides information regarding the proper use of the driver??A?A?s floor mat to avoid any potential interference with the foot pedals. Read More »
-
TSB #09-021-21-3818
AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (6TH GENERATION). All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready ... Read More »
-
TSB #SA-030-21a
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method A. Read More »
-
TSB #SA-041-21
Accessory instructions can be found on OneMazda under Dealer Resources - Parts & Accessories. The links provided below can be used for quick access: For 2016 models and newer: NOTE: Instructions are found under the "Attachments" section ... Read More »
-
TSB #SA-029-21a
APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
-
TSB #SA-034-21
When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the DCA8000 OR GR8 battery charger SST to maintain battery voltage. Read More »
-
TSB #MT-002-21
When programming a key or installing a Genuine Mazda Accessory Remote Engine Start system, you may encounter programming difficulty. Read More »
-
TSB #MT-001-21
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #SA-030-21
Auxiliary key blank cutting procedure: There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method, B. Auxiliary Key Code Cut Method Read More »
-
TSB #SA-029-21
APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay??A?A? / Android Auto??A?A?, but it can be activated using MDARS. Read More »
-
TSB #SA-019-21a
MAZDA CONNECT Symptom Troubleshooting (6th Generation Vehicles). Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-017-21a
CHECK ENGINE LIGHT ON WITH DTC P0126:00 AND ENGINE RUNNING COOLER THAN NORMAL / POOR HEATER PERFORMANCE / LOW ENGINE COOLANT TEMPERATURE (BLUE) LIGHT ON: Some customers may experience the CHECK ENGINE LIGHT ON with DTC P0126:00 ... Read More »
-
TSB #CSP05c
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
-
TSB #CSP05d
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
-
TSB #01-003-21-3776
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. Read More »
-
TSB #07-001-21-3775
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #09-002-21-3770
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer Read More »
-
TSB #CSP05b
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #SA-004-20c
In order to ensure key code security, MNAO has restricted key code access for the new auxiliary key. This Service Alert provides information on how to obtain the 10-digit key code needed for cutting a new auxiliary key blank if all ... Read More »
-
TSB #09-007-20-3674a
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Read More »
-
TSB #SA-058-20c
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #SA-035-20b
Some customers may experience the CHECK ENGINE LIGHT ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. Read More »
-
TSB #CSP05a
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #CSP05
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #04-007-20-3713a
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. Read More »
-
TSB #01-006-20-3695b
Some vehicle may exhibit a tapping noise from the engine during idling; etc., and synchronized to the engine rpm. Read More »
-
TSB #SA-071-20
Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. Read More »
-
TSB #04-002-20-3643b
Some vehicles may exhibit a groan noise from the front brakes when braking at a very low speed (approximately 6 mph/10 km/h). Read More »
-
TSB #SA-070-20
APPLE CARPLAY / ANDROID AUTO FREQUENTLY ASKED QUESTIONS (FAQ): NOTE: The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
-
TSB #SA-069-20
ACCESSORY INSTRUCTIONS LOCATION: Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.mazdausa.com Read More »
-
TSB #SA-061-20a
If you receive a customer concern about the CHECK IN light coming on and DTC P3400 (cylinder deactivation system malfunction) stored, the cylinder deactivation oil control valve may be plugged with plastic debris from the oil filter ... Read More »
-
TSB #SA-062-20
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ... Read More »
-
TSB #09-006-20-3673a
When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #MT-001-20
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #05-003-20-3725
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #01-008-20-3694
Some customers may experience the CHECK ENGINE light ON with DTC P2229:00 stored in PCM memory. ??A?A? P2229:00 (BARO sensor circuit high input). Read More »
-
TSB #SA-041-20
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #SA-032-20
SiriusXM Traffic Plus and Travel Link are displayed with Mazda in-vehicle factory navigation systems. Both of these services provide information in the U.S. & Canada. Read More »
-
TSB #SA-025-20
A valve tapping or knocking noise may be heard from the top end after the engine cools down (the vehicle is parked overnight) or after it has been idling for an extended time. Read More »
-
TSB #SA-026-20
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Audio System, Bluetooth??A?, Center Dislay, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux ... Read More »
-
TSB #SA-020-20
Due to a vehicle side logic change for the vehicles listed above, the seat warming and seat ventilation systems will no longer automatically turn on when the vehicle is started using the MMS accessory. Read More »
-
TSB #09-006-20-3673
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #09-008-20-3675
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #02-002-20-3651
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #09-003-20-3671
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #MT-002-19
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
-
TSB #09-022-19-3599a
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #01-023-19-3648
Some vehicles may exhibit engine overheating with one or more of the following symptoms: ??A?A? ??A?A?EXCESSIVE ENGINE TEMPERATURE: ENGINE OUTPUT WILL BE LIMITED??A?A? displayed in the instrument cluster ??A?A? Red overheating indicator ... Read More »
-
TSB #07-002-19-3616a
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #01-022-19-3657
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
-
TSB #SA-027-19
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
-
TSB #SA-049-19
Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint: ??A?A? MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE ??A?A? CANNOT COMMUNICATE WITH ... Read More »
-
TSB #MT-004-19
Some customers may complain about: ??A?A? Intermittent engine no start ??A?A? Instrument cluster red security indicator light ON ??A?A? Engine Start/Start Button Amber indicator light flashing ??A?A? Battery discharge ??A?A? Electrical ... Read More »
-
TSB #RF-18-02R3
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. Read More »
-
TSB #09-031-19-3625
After the installation of a new instrument cluster, the message "Fctry" or ??A???A???A?Factory??A???A???A? is displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Read More »
-
TSB #SA-029-19a
The database error discovered with IDS 114.00-114.02 release has been fixed with IDS 114.04 release and is now available for download. Read More »
-
TSB #SA-031-19
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #07-002-19-3616
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #SA-029-19
Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. Read More »
-
TSB #SA-027-19
ACCESSORY INSTRUCTIONS LOCATION: Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/ Read More »
-
TSB #09-022-19-3599
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #SA-001-19b
APPLE CARPLAY??A?A? / ANDROID AUTO??A?A? FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #SA-002-19a
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. Read More »
-
TSB #SA-013-19
MAZDA IDS INOPERATIVE WITH VCM-II LICENSE EXPIRATION MESSAGE - If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. Read More »
-
TSB #SA-001-19a
APPLE CARPLAY??A?A? / ANDROID AUTO??A?A? FREQUENTLY ASKED QUESTIONS (FAQ). Many frequently asked question and the answers. Read More »
-
TSB #00-003-19-3583
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
-
TSB #SA-007-19
SiriusXM Traffic Plus and Travel Link are displayed with Mazda in-vehicle factory navigation systems. Both of these services provide information in the U.S. & Canada. Read More »
-
TSB #09-007-19-3564a
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH? hands-free unit or text messaging related concerns. Read More »
-
TSB #SA-001-19a
APPLE CARPLAY? / ANDROID AUTO? FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #00-001-19-3560
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #09-005-19-3562
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #09-007-19-3564
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH? hands-free unit or text messaging related concerns. Read More »
-
TSB #09-004-19-3543
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Read More »
-
TSB #SA-001-19
APPLE CARPLAY? / ANDROID AUTO? FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #09-001-19-3553
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as ... Read More »
-
TSB #SA-005-18
Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition. Read More »
-
TSB #SA-049-18
SiriusXM Traffic Plus and Travel Link are displayed with Mazda in-vehicle factory navigation systems. Both of these services provide information in the U.S. & Canada. Read More »
-
TSB #09-010-18-3440b
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #MT-002-18
Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth? and the same device is also connected to the USB port for charging. Read More »
-
TSB #MT-011-18
SMS (Short Message Service) messages received by paired phones (Android and iPhone 5 iOS 7.0 or higher) can be downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. Read More »
-
TSB #01-022-18-3528a
Some vehicles may exhibit an excessive body vibration/unusual noise when idling or driving after parking inextremely cold temperatures (-25?C/-13?F). NOTE: This excessive vibration does not occur if the engine mount rubber No. Read More »
-
TSB #00-001-18-3446a
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #00-003-18-3480a
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. Read More »
-
TSB #09-014-18-3443a
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #09-020-18-3458b
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH? hands-free unit or text messaging related concerns. Read More »
-
TSB #09-021-18-3459a
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #09-034-18-3430a
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #MT-004-18
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #CSP02
CSP02 - Apple CarPlay and Android Auto - Parts and Warranty Information. As previously communicated, Apple CarPlay? and Android Auto? will soon be available as a Genuine Mazda Accessory for the 2018 Mazda6 beginning in early September. Read More »
-
TSB #MT-004-18
ELECTRICAL CONCERN AND/OR MULTIPLE DTC'S DUE TO AFTERMARKET DEVICE: If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored... Read More »
-
TSB #SA-034-18
MAZDA CONNECT SYSTEM FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #SA-031-18
When troubleshooting a radar unit, DO NOT swap it with another vehicle. Radar units are configured to the original vehicle, and if installed in another vehicle, a configuration error will occur. Read More »
-
TSB #09-020-18-3458a
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH? hands-free unit or text messaging related concerns. Read More »
-
TSB #09-025-18-3479
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Read More »
-
TSB #09-023-18-3475
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as ... Read More »
-
TSB #SA-025-18
When performing the MGSS Workshop Manual 360? View Monitor System Aiming Procedure, M-MDS may show error message "Procedure unsuccessful". This may be caused by light glare on the SST. Read More »
-
TSB #00-002-18-3463
In support of the new Mazda6 Signature model, Mazda will make available for loan on a "as-needed" basis, a Special Service Tool (SST) to allow for the aiming of the 360 Degree Camera System. Read More »
-
TSB #01-011-18-3456
The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazdamodels, there is no key cylinder on the steering column. Read More »
-
TSB #MT-004-18
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
-
TSB #00-001-18-3446
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-008-18
Some customers may complain about the MAZDA CONNECT center display cracking (spider cracking). The cracks are internal and cannot be felt by touch. This may be caused by a faulty center display. Read More »
-
TSB #MT-003-18
The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles. Read More »
-
TSB #SA266
MAZDA Mobile start (MMS) cannot communicate with vehicle Read More »
-
TSB #SA-016-23
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method Read More »
-
TSB #SA-026-20a
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-031-19
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #SA-007-19
SiriusXM Traffic Plus and Travel Link are displayed with Mazda in-vehicle factory navigation systems. Both of these services provide information in the U.S. & Canada. Read More »
-
TSB #SA-046-18
APPLE CARPLAY? / ANDROID AUTO? FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #09-020-18-3458b
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH? hands-free unit or text messaging related concerns. Read More »
-
TSB #CSP02
CSP02 - Apple CarPlay and Android Auto - Parts and Warranty Information. As previously communicated, Apple CarPlay? and Android Auto? will soon be available as a Genuine Mazda Accessory for the 2018 Mazda6 beginning in early September. Read More »
-
TSB #MT-008-18
ENGINE NO START (KEY NOT DETECTED): Some customers may complain about the following: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing. Read More »
-
TSB #SA-025-18
When performing the MGSS Workshop Manual 360? View Monitor System Aiming Procedure, M-MDS may show error message "Procedure unsuccessful". This may be caused by light glare on the SST. Read More »
-
TSB #09-020-18-3458
Some vehicles may exhibit BLUETOOTH? hands-free and/or text messaging related concerns. To improve the handling of BLUETOOTH? hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program ... Read More »
-
TSB #SA-018-18
The 360 degree View Monitor System is new for i-ACTIVSENSE on the 2018 Mazda6 Signature. During PDI, make sure all 4 cameras (front (1), right side (2), left side (3) and rear (4)) are working and displaying an image on the MAZDA CONNECT ... Read More »
-
TSB #MT-001-18
When installing a navigation SD card, the center display may show error message "Invalid SD Card". Read More »
-
TSB #SA-047-18
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #09-025-18-3479
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Read More »
-
TSB #09-023-18-3475
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as ... Read More »
-
TSB #SA-005-18
Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition. Read More »
-
TSB #SA-046-21
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #SA-032-20
SiriusXM Traffic Plus and Travel Link are displayed with Mazda in-vehicle factory navigation systems. Both of these services provide information in the U.S. & Canada. Read More »
-
TSB #SA-031-19
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #DRW13
Dealer Rework (DRW) 13 - Mazda Connect Navigation Concern. As you may know, DRW13 was launched in March of 2018. This notice is to advise all dealers that DRW13 will be ending August 16th 2018 and all claims must be submitted by this date. Read More »
-
TSB #SA-012-18
Some 2018 vehicles built after January 1, 2018 and equipped with Navigation may exhibit one of these concerns after the user inputs an address: A screen pops up that says "House number not found. Read More »
-
TSB #SA-001-23a
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: ... Read More »
-
TSB #RF-22-01R2
This Parts Flash replaces RF-22-01R released November 21, 2022. It includes a new display repair kit part number for the 2020-2022 MX-5. Repair kits are available to replace just the screen. Read More »
-
TSB #SA-001-23
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: ... Read More »
-
TSB #SA-041-22c
Some customers may complain about infotainment center display: * Ghost Touch * DTC B108E:04 may be stored (Touch screen operates by itself) * Surface Peeling * DTC B108E:04 may be stored * Spider Cracks * White ... Read More »
-
TSB #SA-041-22
Some customers may complain about infotainment center display: Ghost touch, surface peeling, spider cracks. Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit. Read More »
-
TSB #SA-001-22c
Use the symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #09-021-21-3818a
AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (6TH GENERATION). All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready ... Read More »
-
TSB #22-01R
Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors. Read More »
-
TSB #RF-22-01
Some customers may complain about infotainment center display ghost touch (touch screen operates by itself), surface peeling or spider cracks. Repair kits are available to replace just the screen. Read More »
-
TSB #SA-041-22c
Some customers may complain about infotainment center display: - Ghost Touch (Touch screen operates by itself) - Spider Cracks - Surface Peeling - White dots Read More »
-
TSB #01-014-21-3840
Some vehicles may exhibit the CHECK ENGINE light on with DTC P011B:00 (Engine coolant temperature/IAT: Correlation error) when using an engine block heater which is set up by MCI as local accessory parts. Read More »
-
TSB #SA-006-22a
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #SA-014-22
Accessory instructions can be found on OneMazda under Dealer Resources - Parts & Accessories. Read More »
-
TSB #01-003/22
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #00-001-20-3689
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-036-20
The owner??A?A?s manual contains procedures and precautions for the maintenance and cleaning of plastic parts, like the brand emblem. However, it is still important to remind customers about these precautions. Read More »
-
TSB #00-001-18-3446a
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-015-18
A tapping/rattling noise may be noticed from the valve train area. This condition usually occurs after the engine has been turned off at normal operating temperature and then not warmed up to full operating temperature during the next ... Read More »
-
TSB #SA-009-18
The navigation SD Card VIN-locks to a vehicle in the following conditions: 1. Vehicle odometer under 62 miles ? VIN-lock occurs with key ON for 3 minutes or longer. 2. Vehicle odometer over 62 miles ? VIN-lock occurs at key ON. Read More »
-
TSB #MT-021-17
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. Read More »
-
TSB #09-035-17-3080
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #01-008-17-3376
Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. Read More »
-
TSB #SA-027-24
Some customers may complain about infotainment center display. Peeling, spider cracks and white dots. Read More »
-
TSB #SA-032-23a
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #09-007/22
Some vehicles may exhibit a white powdery dust (1) adhering to the inner surface of the headlight lens causing a poor appearance. Read More »
-
TSB #09-037-21-3839
NOTE: These vehicles are orginally built with the center display GML8-611J0* and are not applicable to this TSB. Read More »
-
TSB #15-004-21-3835
NOTE: This Service Information is only applicable for vehicles equipped with a Forward Sensing Camera (FSC), KDD1-67-XCX and GSH7-67-XCX*. Read More »
-
TSB #SA-019-21e
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns Read More »
-
TSB #01-013-21-3753
Some vehicles may have coolant leaks at the cylinder head around the exhaust manifold (as shown below). There may be cracks at the stud bolt hole (1) or at the outside of the exhaust manifold (2). Read More »
-
TSB #SA-031-21c
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #09-021-21-3818b
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #15-002-21-3812
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #SA-019-21a
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-036-21
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
-
TSB #SA-022-21
When performing the MGSS Workshop Manual 360??A? View Monitor System Aiming Procedure, M-MDS may show error message "Procedure unsuccessful". This may be caused by light glare on the SST. Read More »
-
TSB #SA-058-20c
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Read More »
-
TSB #MT-006-20
Some customers may complain about the following MAZDA CONNECT??A?A? Temperature Warning message: ??A?A? Display is too Hot. Screen performance may be decreased until it cools. Read More »
-
TSB #09-036-20-3756
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH??A? hands-free unit or text messaging related concerns. Read More »
-
TSB #01-006-20-3695b
Some vehicle may exhibit a tapping noise from the engine during idling; etc., and synchronized to the engine rpm. Read More »
-
TSB #15-003-20-3737a
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] (Error signal received from electric power steering (EPS) control module) stored in memory. Read More »
-
TSB #09-030-20-3740
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #15-003-20-3737
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. Read More »
-
TSB #SA-062-20
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ... Read More »
-
TSB #05-003-20-3725
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #SA-037-20
Some vehicles may have one of the following DTCs stored in memory: ??A?A? C1001:92 - Forward sensing camera (FSC) poor field of view ??A?A? B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set ... Read More »
-
TSB #SA-011-20a
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
-
TSB #SA-025-20
A valve tapping or knocking noise may be heard from the top end after the engine cools down (the vehicle is parked overnight) or after it has been idling for an extended time. Read More »
-
TSB #01-002-20-3678
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. Read More »
-
TSB #SA-011-20
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
-
TSB #02-002-20-3651
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #09-022-19-3599a
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #07-002-19-3616a
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #01-022-19-3657
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
-
TSB #SA-027-19
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
-
TSB #09-022-19-3599
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #SA-018-19
Due to a changes in the 2018 Mazda6, there are two things to note of when installing the Rear Parking Sensors. 1. When securing the main harness in step 4, DO NOT attach the one tie wrap as shown. Read More »
-
TSB #SA-006-19a
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #15-002-19-3542a
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). Read More »
-
TSB #09-002-19-3554
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. Read More »
-
TSB #09-019-18-3450
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. Read More »
-
TSB #07-002-19-3616a
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #07-002-19-3616
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #07-002-18-3432
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #07-007-17-3384
Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a clogged heater unit. Read More »
-
TSB #SA-027-24
Some customers may complain about infotainment center display. Peeling, spider cracks and white dots. Read More »
-
TSB #07-003-24
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10 A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
-
TSB #SA-039-22
Some customers may complain about scratches on the instrument cluster lens. Read More »
-
TSB #SA-001-22c
Use the symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #MT-001-22
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Read More »
-
TSB #SA-058-19
WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the ... Read More »