The contact owns a 2022 Toyota Tundra. The contact stated that on several occasions while driving at an undisclosed speed, the vehicle stalled. No warning light was illuminated. The contact stated that the message to "Shift to Park and Restart" was displayed. In addition, the contact stated that the vehicle had stalled on the freeway. The vehicle was taken to a local dealer where it was diagnosed but the failure could not be replicated. The vehicle was not repaired. The vehicle was taken to another local dealer, Beaverton Toyota (4300 SW Murray Blvd, Beaverton, OR 97005) for a second opinion; however, the failure was not diagnosed or replicated. The contact received a notification of NHTSA Campaign Number: 23V566000 (Fuel System, Gasoline); however, because the vehicle was not diagnosed, it was unknown if the failure was related to the recall. The vehicle was left at the local dealer for further testing. The manufacturer was made aware of the failure. The failure mileage was approximately 11,000.

- Portland, OR, USA

This truck has a recurring issue of when you press the accelerator pedal there is no throttle response. After a second or two it responds to the throttle. It-??s unsafe as the truck does not respond so it doesn-??t move. This throttle delay could cause an accident.

- Corona , CA, USA

While on highway truck decelerated on its own. We were trying 70 mph and the truck dropped to 60 mph while the gas pedal was still manually engaged. Its becoming an increaingly regular problem that the car will not accelerate from a complete stop, even with gas pedal fully engaged. Potential for accident is high, as there is no reliability when pulling out into traffic. Dealership ran diagnositic check during service, was unable to pin-point issue - - is also 2 to 3 months out on service schedule, so issue was reported early June to dealership but unable to service vehicle until mid-August. Dealerships advice was to report directly to Toyota - since no recall remedy was issued for engine issue and the acceleration issue isn't specifically named in their most recent recall for the 2022 model.

- Key West, FL, USA

On 07/10 while accelerating from red to green light, at around 50mph truck shook and alerted my attention to dash/odometer because of immediate slowing of truck. Noticed alert for -??Engine Power Loss-?? and -??Brake Failure-?? and instructed to see dealer. Could not go above 30mph at 2500rpm, thankfully I was 5 minutes from home. Had Tundra towed to dealer. They got Toyota involved and started a case. As of 07/12, dealer was instructed to reset engine valve settings, cleared alerts, and did normal schedule maintenance. I was instructed to drive directly to dealer or pull over where I was and have a technician drive to my location so they could further assess this issue. As if they work 24/7 and would drive outside of city limits-??I put 100+ miles a day on my truck for my work commute.

- Houma, LA, USA

At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).

- Celina, TX, USA

At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).

- Celina, TX, USA

At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).

- Celina, TX, USA

At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).

- Celina, TX, USA

At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).

- Celina, TX, USA

At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).

- Celina, TX, USA

At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).

- Celina, TX, USA

At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).

- Celina, TX, USA

Vehicle failed to move forward or reverse from a stand still. Once vehicle is shutdown and restarted, the problem does not return. When vehicle was sent to dealer it couldn't be duplicated. If this issue occurs on the open road, it could cause a collision.

- Las Vegas, NV, USA

In certain conditions, vehicle exhibiting unresponsive accelerator pedal. This appears to occur when vehicle is transitioning from a rolling stop to an acceleration condition. There is a 2-3 second delay and then the vehicle responds. T-SB-0111-22 has been applied to the vehicle, but condition remains This is causing an unsafe condition as one attempts to merge into traffic. Natural tendency is to apply more acceleration during these "dead pedal" conditions, and when power finally arrives, the vehicle lurches and sometimes will spin the tires. Numerous other people on forums have reported this condition and as of yet Toyota or Dealers have not been able to fix the problem

- Maple Grove, MN, USA

Pulled into road and while merging vehicle engine stalled. Had to pull over in grass, turn off, restart. Afterwards, felt like it did not provide full power

- Evans , GA, USA

The contact owns a 2022 Toyota Tundra. The contact received notification of NHTSA Campaign Numbers:?23V142000 (Structure), 23V566000 (Fuel System, Gasoline), and 24V125000 (Power Train), and would like to be removed from the recall distribution list because he no longer owns the vehicle. The manufacturer was contacted.

- Broussard, LA, USA

My 2022 Toyota Tundra was serviced regularly at the dealership since it was purchased brand new in December of 2021. I made a point to have it checked out as much as possible due to concerns that were raised by the dealer and online resources that the truck could possibly have major engine issues. On March 26th of 2024 I took my truck to the dealer to have it serviced and they completed everything necessary according to the maintenance recommendations. On April 1st, the following week after service, my engine cut off as I was merging onto the exit lane on I-40 in heavy traffic. I coasted to the bottom of the exit ramp and shifted the truck into park to try restart it. It would not restart so I was stuck in the middle of the ramp at a light until a tow truck came to assist me. After pushing the truck in the grass of the median it was loaded and taken to the nearest Toyota dealership. The next day I received a call that they would need to pull my oil pan to examine it due to the fact that they believed my engine was locked up. Once they pulled the pan and assessed the damage to the tune of $700, I was told that my engine and both of my turbos would need to be replaced because everything was full of metal shavings due to catastrophic engine failure. The total bill would be around $24000 for a truck that is 2 years old. Now the warranty on this particular truck is up to 60,000 miles and I am at 64,000. The dealership said that due to the fact that my truck was out of warranty I would have to take it up with Toyota. I have called Toyota customer care and still have not gotten anyone to respond to me. I called my local dealership where I have been getting my service and the manager stated to me that Toyota is aware of this issue but they are not recalling the vehicles yet. There are more than enough of these trucks with this problem to force Toyota to do something about it, but they have refused to accept responsibility for it. I could have died. I was lucky.

- Greensboro, NC, USA

Was driving at 55 mph on a side road and started to notice pulsing/mechanical noises from the engine. After 3 minutes the Check Engine Light came on with a warning 'Take Vehicle to Dealership' and a few seconds later the engine shut off in Drive at 55 mph. Lost power steering and coasted to a neighborhood to be towed. Was not able to restart the vehicle.

- Medina, OH, USA

My 2022 Toyota Tundra 1794 transmission has always shifted hard on the initial start up and while accelerating when changing lanes. Since the truck was new I thought it was due to being new and required a break in period. Now I have own the truck for 15 months the problem still exist. I took the truck to the Toyota Dealership in Moss Point Mississippi in November 2023 and they informed me there were an update computer software program needed to be installed on my Tundra and the problem would be resolved. The problem still exist, the jerking of the transmission has me afraid to drive it.

- Biloxi, MS, USA

The contact owns a 2022 Toyota Tundra. The contact stated that the throttle was lagging, causing the vehicle to hesitate while accelerating. There was approximately 2-seconds after depressing the accelerator pedal before the vehicle would lunge forward. There were no warning lights illuminated. The failure occurred intermittently. The vehicle had been taken to the dealer who was unable to determine the cause of the failure. The contact was informed that it was a known failure however, there was no known fix. The vehicle had not been repaired. The manufacturer was made aware of the failure and opened a case. The approximate failure mileage was 14,000.

- Greensboro, NC, USA