I was going 40MPH when my car started to produce loud noises and stalled. It immediately lost power and I had to pull over on the side of the road. It started back up after 30 minutes and I was able to drive it home, but it continued to make loud noises and I had to drive very slow. Battery is good with 70% charge and the alternator is good.

- Belleville, IL, USA

The electrical plate for the right daytime running light must have fallen out of the engine compartment, according to the dealer service center, because it was no longer there. A warning light appeared on the dashboard system as a yellow triangle enclosing a yellow exclamation mark. It presented a safety issue by causing the warning light to appear on the dashboard panel while the vehicle was being driven. The dealer service center informed me of the cause of the dashboard warning light when I took it to them for diagnosis. There were no warnings prior to the failure.

- Houston, TX, USA

When Daylight Savings time changed, I realized that my headlights were not aimed properly. While having them aimed, the tech noticed that the aiming rod had fallen off the track, and the light on the drivers side is shining only five feet from the car, onto the ground, whether on high beams or low beams.

- Roebuck, SC, USA

High beams quit working I. Weather conditions and now high beams don-??t work period and have to replace head light do to problem with assembly driver side and passenger side high beams don-??t work

- Sand Springs, OK, USA

The high beam does not work even after bulb replacement on the 2019 Elantra(the low beams work just fine). A sound of an actuator trying to work is heard coming from the engine with a slight flicker of light but no successful high beam is shown after engaging the high beam actuator on the wheel. This is detrimental to the safety of drivers at night which could lead to a crash, injury, or fatality.

- Jacksonville, FL, USA

The high beam nolonger functions. On this make model for this year, the manufacturer uses only one bulb for low and high beam. This is accomplished by using a hood to shield part of the bulb; lowered for low beams, raised for high beams. The problem is the mechanism used to raise and lower the shield is made out of cheap plastic. Whenever the gears break or skip a cog the shield will not raise. Spending 2 labor shop hours to replace two shield mechanisms, cheap plastic parts with cheap plastic parts is not the answer. Multiple owners have ask Hyundai to find a better fix-?? all for not.

- Manchester, NH, USA

The high beam headlights don-??t function properly. The low beam is all that works on both headlights. Something to do with the way the shield is not moving up to allow the high beams to function. On line looks like this is a common problem

- Corpus Christi , TX, USA

High beams are not working on both headlight assemblies. Car uses a bulb with 1 filament and actuator to simulate a high beam and both headlight assembly actuators failed on a car with 51k miles. Hyundai has a TSB for this issue, so they are aware of this issue and this needs to be a recall, not just a TSB as this is a major safety issue.

- Apopka, FL, USA

My high beam lights stopped working. Replaced bulbs and they still don-€™t work.

- Tuscaloosa, AL, USA

When I was driving in very dark areas I was trying to turn on my high beams. I have manual headlights so I have to push the lever back. I see the high beam logo on the dashboard, but no lights appearing higher than the low beams. I searched up that it-€™s a common recall for the 2019 Hyundai Elantra-€™s and I believe I have that problem with my car. I hope that this description helps out in making the decision as soon as possible. Thank you!

- Pomona, NY, USA

Dim headlights and faulty high beam lights that do not work at all; while the sensor remains lit up on the dash board.

- Philadelphia , PA, USA

the high beam actuator has failed which has resulted in loss of high beam usage.

- Norman, OK, USA

The headlight high beams do not function, leaving me unable to see.

- West Warwick, RI, USA

The High beams will not engage lights stay on dim mode

- Athens, GA, USA

Trouble code:P0011 Mechanic replaced timing soliend. On driving car home, the engine began shutting down. Took back to mechanic who stated he could not get the engine to repeat trouble. Continue to drive and see what happens. Continued to drive but engine shut down got continuously worse and there is a sound like a fan blade is knocking against something (best way I can describe the noise)which is intermittent. Headlights are very dim. This was noticed late last year. It got so bad that I started to Google it and found there are other companies about this online including that the high beams don't work at all.

- Phoenix, AZ, USA

The headlamp actuator inside the headlight assembly that flips to reveal high beams or low beams is made of a cheap, flimsy plastic that wears down quickly. When it is worn down, the rod can no longer control whether high beams or low beams are shown. Because of this, this car is stuck with either high beams or no headlights at all. This is extremely unsafe for nighttime driving as you are stuck being invisible and likely to be hit by another car or alternatively, blinding the other occupants of the road at night. A full headlight assembly replacement is required which numbers to nearly $3000 for both sides. However, the replacement is going to have the same issue down the line due to the non-durable material of the shutter. There have been many complaints on Youtube and Hyundai forums about this exact issue, but there has yet to be a recall of any sort despite the safety hazard this presents.

- Knoxville, TN, USA

both headlights will not show brights is there a recall on this vehicle. I have seen youtube clips showing the autodialers with a recall fix. please advise [XXX] INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).

- Great Falls, MT, USA

Lights do not shine correctly on road, the dealership says that's how they were made and I even paid for them to put led lights bulbs in. It is dangerous at night driving.

- Dayton, TX, USA

Headlight stay in Dim mode will not switch to Bright Lights

- Patterson, LA, USA

Low beam headlights work fine. When engaging the high beam selector the high beams on both the left and right side do not work. There seems to be a lens that does not actuate to enable the high beams to shine.

- Warner Robins, GA, USA