The Office of Defects Investigations (ODI) is an office within the NHTSA which investigates serious safety problems in the design, construction or performance of vehicles. The NHTSA is authorized to order manufacturers to recall and repair vehicles, if the ODI finds a safety issue. NHTSA investigations for the 2010 Mazda CX-9, both ongoing and closed, are listed below:

  1. INVESTIGATION: Inadvertent Curtain Air Bag Deployment

    NHTSA Preliminary Evaluation #PE19006

    • Status:
    • Date Opened: May 02, 2019
    • Date Closed: N/A
    • Recall: No recall yet

    Component(s): Air Bags
    Air Bags: Roll Protection
    Air Bags:Side/Window

    Summary: The Office of Defects Investigation (ODI) has received two complaints (VOQs) and additional Early Warning Report (EWR) data alleging non-crash, inadvertent, simultaneous deployment of the left and right curtain side air bags. All incidents occurred while the vehicle was in motion. One VOQ and additional EWR reports allege injuries resulted from the air bag deployment. A Preliminary Evaluation has been opened to assess the scope, frequency, and safety consequences of the alleged defect.The following VOQ numbers are associated with the issues discussed in this opening resume: 11165925, 10905492.

  2. INVESTIGATION: Brake Booster Failure

    NHTSA Preliminary Evaluation #PE14005

    • Status:
    • Date Opened: February 10, 2014
    • Date Closed: June 26, 2014
    • Recall: No recall issued

    Component(s): Service Brakes, Hydraulic:Power Assist

    Summary: In March 2014, Mazda Motor Corporation (Mazda) initiated Special Service Program SSP93 to extend the warranty coverage for a specific brake booster fault condition on model year (MY) 2007-2013 Mazda CX-9 vehicles.According to Mazda's dealer communication for SSP93, the subject vehicles may exhibit a condition were the brake pedal is harder than usual to depress. Complainants report hearing air leakage (hissing) from the driver-side foot area during braking.The Mazda program extends the warranty coverage for repairing this condition to unlimited time and mileage for repairs performed between March 31, 2014 and March 31, 2015 and to 7 years or 90,000 miles for repairs performed after March 31, 2015.In its response to the Office of Defects Investigation's (ODI) information request letter for PE14-005, Mazda identified a problem with booster diaphragms developing tears near the outer seal/circumference that can result in noise and degraded booster performance as the tears grow in length (Figures 1-3).The tears allow leakage from the ambient to the vacuum sides of the diaphragm that reduces the differential pressure across the diaphragm and produces a hissing noise after the tears have reached 10-12 mm in length.The problem was caused by wear of the mold used for the diaphragm forming process, which resulted in increased thickness and stress in the bending area of the diaphragm.Continuous operation in environments with high ambient temperatures accelerates the hardening of the diaphragm material, further increasing the stress in the bending area and contributing to tear initiation and propagation rate.Analysis of failure data indicates that the tool wear condition affected vehicles produced after June 2010 and operated in hot states (Figures 4-6).In February 2013 the supplier introduced a new mold and changes to the diaphragm thickness monitoring process to correct the condition in production vehicles.Analysis of complaint and supplier test data indicates that the diaphragm tear condition is a progressive failure that develops slowly over time.Smaller tears have little effect on system performance.As the tear continues to grow, the effects become more evident.The hard pedal and increased effort are experienced during initial pedal application, but are diminished as the pedal is pressed further by the driver and the tear is partially sealed by the outer wall of the booster.This change from a hard to a soft pedal feel is described by some drivers as a spongy pedal.For tear lengths that were observed in warranty return parts, testing demonstrated that most booster performance can be recovered with increasing pedal apply speed and apply force.None of the tears measured in return parts grew large enough to cause a complete loss of brake booster function. The booster diaphragm tear condition results in partial reduction in booster function that progresses gradually over time with audible and pedal feel symptoms available to the driver.The condition does not result in a sudden loss of power braking assist.The effects are evident during initial pedal apply and are reduced by increased pedal apply force and rate.ODI has not identified any accidents associated with the booster diaphragm tear condition in the subject vehicles.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will continue to monitor complaints and other information relating to the alleged defect and take further action in the future if warranted.VOQs (24) associated with this investigation:10482005, 10486941, 10487938, 10493043, 10512943, 10523477, 10523719, 10533815, 10534545, 10535301, 10535955, 10542334, 10546804, 10546841, 10547859, 10550555, 10556021, 10560699, 10564520, 10565646, 10566803, 10573705, 10574868, 10575714

  3. INVESTIGATION: Lower ball joint separation

    NHTSA Preliminary Evaluation #PE15022

    Component(s): Suspension:Front:Control Arm:Lower Ball Joint

    Summary: In an July 7,2015 letter to NHTSA, Mazda identified a safety defect that could result in lower ball joint separation in approximately 193,484 model year (MY) 2007 through 2014 Mazda CX-9 vehicles (NHTSA Recall No. 15V-451, Mazda 8515G).Mazda indicated that damage to the ball joint boot may allow water to enter the front suspension ball joint fitting during use which may result in premature ball joint wear and a progressively looser joint.In January 2014, Mazda implemented redesigned lower control arms in production vehicles to improve the durability of the lower ball joints.The redesign involved changing the shape of the top surface of the ball joint boot cover and adding a suspension plate to the undersurface of the knuckle.Mazda's recall will replace the defect lower control arms with the redesigned parts.ODI's analysis of information collected during PE15-022 identified a total of 62 ball joint separation incidents, including 34 identified in ODI complaints and 31 identified in Mazda complaints and field reports (3 of the Mazda records involve vehicles/incidents that were also reported to ODI).When Mazda's design change was implemented, most of the field experience related to lower ball joints involved complaints of noise and premature wear-out.Only 1 of the ODI and 6 of the additional Mazda separation complaints identified in ODI's analysis were reported prior to January 2014.Significant increases in the number and trend in separation complaints were observed in 2015, when 30 of the ODI complaints and 16 of the additional Mazda complaints were reported.The report trend appears to be accelerating, with 29 of the reports received after ODI opened PE15-022 on June 9, 2015.There has been one crash reported to ODI related to the alleged defect (VOQ 10746510). This investigation is closed based on Mazda's recall.The 34 VOQs associated with this investigation are: 10747358, 10746510, 10744897, 10743509, 10736229, 10735938, 10734763, 10734302, 10734290, 10733813, 10732578, 10732217, 10732154, 10731850, 10730736, 10730280, 10730143, 10730114, 10726622, 10726480 10726448, 10726168, 10725839, 10725567, 10725488, 10725427, 10725390, 10717510, 10714469, 10695142, 10668978, 10648429, 10640541, 10546535