The ABS Control Module is not functioning correctly and is constantly creating a fault light on the dash even when the code is cleared. All four wheel speed sensors have been tested and/or replaced, the issue remains. The safety aspect of this is when the brake is applied it -??defaults-?? to ABS ratchet mode even at slow speeds. If the brakes are applied when going downhill, the ABS engages and the vehicles slides. This could lead to failure to stop and go into a busy intersection. This issue has gone on for two years, no replacement part (the module) can be purchased because Jeep is re-engineering it, for at least the last two years. I consider the vehicle too dangerous to drive without the replacement part. Jeep is fully aware of this issue.

- Nanjemoy, MD, USA

ABS and Traction Control lights are on. Sometimes Emergency Brake light comes on causing it to go into -??limp mode-??. This is dangerous for me bc this is my Mail Jeep. I-??m driving on roads where the speed limits are sometimes posted at 55mph. Mechanic replaced the rear wheel sensors because the computer indicated that was the problem. Did not fix the problem. The ABS Module has to be replaced and they-??re on back order. Forums online have many different people stating they-??re having the same problem with JEEP. JEEP parts department stating it could be a year or more before the part comes in and is available.

- Saluda, NC, USA

After dash lights came on, my issue was diagnosed as an ABS module failure by my mechanic. Jeep offers no repair. Options are limited and expensive. I-??m driving on 1985 brakes until repaired. I understand this is a problem common to JK models and has been occurring for years.

- Daytona Beach, FL, USA

I am on my 4th set of front brake calipers. the last 3 have been replaced at a Wyler Jeep 5881 Gender Rd. Canal Winchester, Ohio 43110...Phone 614-834-6080 and now I am having issues with my left front brake again... This has been in for this service the following times 5/15/2023(could not drive due to brakes locking up) 5/162023 7/5/2023 3/4/2025 (was told not to drive) and now I have to take back up 7/11/2025... I have contacted Jeep and I have a Case #[XXX] The past 3 times they were put on for free under part warranty, and I did receive a courtesy vehicle to drive... I don't want to continue to do this every year or two INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

- Lancaster, OH, USA

The ABS module was diagnosed as the cause of multiple warning lights appearing on the dashboard, including the ABS light, parking brake light, and traction control light. According to an ASE certified technician, the failure of the ABS module disabled the antilock braking system as well as the cruise control feature. This issue resulted in loss of antilock braking function and reduced overall vehicle safety. The problem was identified and confirmed by a qualified technician. These warning lights first appeared prior to the failure being diagnosed. At this time, the original equipment manufacturer (OEM) replacement part is on at least a three-month backorder.

- Lantana, FL, USA

I was traveling down the street in my town going about 40-45 and all of a sudden the dash lights came on and there was no control of the Jeep. I happened to be close to my mechanic shop so we got it there. No one was hurt but there was no warning that the abs module had gone out. I had to have it towed to a Jeep dealership in Topeka. Ks where it still sits 6 weeks later due to Jeep/ Mopar holding it hostage with no resolution to the ABS module shortage. I am being told there are none in production and there is no ETA for production and shipment.

- Louisburg, KS, USA

May 14, 2025 Dear NHTSA, I am submitting this complaint regarding my 2017 Jeep Wrangler Unlimited Sahara, which has only 60,000 miles and has already required several major repairs that raise serious safety concerns. To date, I have had to replace three brake calipers and the emergency brake, at a cost of over $2,500. The calipers were seizing, and the emergency brake would not release properly, both of which posed clear risks while driving. I understand through forums and peer discussions that other owners have faced similar issues. In addition, my vehicle now has an oil leak that will cost over $700 to repair, and the windshield washer fluid hose burst, requiring another replacement. These repeated failures on a relatively low-mileage vehicle suggest underlying quality and reliability issues. I believe these concerns warrant review, particularly the safety-related brake defects. I respectfully ask NHTSA to investigate whether these failures are part of a broader pattern that may justify further scrutiny or a formal recall. Thank you for your attention.

- Hardwick, MA, USA

Cruise control was not working. The Jeep would also idle too fast when stopped but not get to the proper speed while driving. ABS brake light was on with code that rear wheel brake sensor was not working. Sensor was replaced but it still doesn't work. C. Harper Jeep garage in Connellsville, PA says the ABS module is bad and not supplying power to the wheel sensors. This part is supposedly on back order with no known time of availability. The fuel injector also needed replaced but not sure what caused that problem. Other 2017 Jeeps had recalls for electrical problems but seems that my vin was not, maybe it should have been!

- Dawson , PA, USA

ABS module failed 2 years ago. No traction control, no cruise control, no stability management. This part has been on backorder for 2 years and affects many years. Issue started intermittently about 3 years ago while driving, now the vehicle is extremely unstable in wet conditions. Dealership has diagnosed and said to check back every few months for a solution. Additionally the plastic oil filter housing has been replaced 2 times in 2 years at a cost of $1,200, the second install was covered by parts warranty. Dealers won't install the metal version available on other years that do not have a cracking issue, aftermarket metal versions are available but dealers won't install them.

- Cape Coral, FL, USA

While Driving ABS, Brake, and Traction Control lights came on simultaneously. Had error codes read and was issuing a C2200 error signifying that ABS control module had failed. Contacted local Dealership to obtain part and was informed by Martin Dodge in Cleveland Texas that the part was not being manufactured because of an engineering issue. Am concerned that this is an issue for all similar vehicles that use the same module and am driving a vehicle without all of its safety features available or even repairable at this time.

- Shepherd, TX, USA

Power stop brake hose kit was recalled do to leaks part# BH00139 Amazon order # 112-6473860 / 113-5400733 Recall report 24E-053 Front hose began to leak causing me to loose pressure in the brake system and loosing brakes. Had to have the brake lines replaced

- Bechtelsville, PA, USA

File has been attached.

- Derry, NH, USA

Brakes keep dragging, getting hot and seizing. I have done four complete brake jobs and the vehicle has only 40,000 miles on it. Most recent time the wheel rim was so hot you couldn-??t put your hand on it. Cost so far, over $6,000. Google searches indicate that this is a recurring issue on this model and year.

- Davenport, IA, USA

The contact owns a 2017 Jeep Wrangler. The contact stated that while his wife was driving approximately 30 MPH, the driver's side front brake locked up. The contact stated that his wife had not observed any warning lights being illuminated. The vehicle was driven back to the residence. The vehicle was stopped and parked, and the contact stated that there was smoke coming from the driver's side front wheel well. The contact had not taken the vehicle to a local dealer or independent mechanic. The vehicle was not diagnosed or repaired. The manufacturer was not informed of the failure. The failure mileage was 91,914.

- Croswell, MI, USA

The contact owns a 2017 Jeep Wrangler. The contact stated while driving at an undisclosed speed, the service brakes warning light illuminated. The vehicle was taken to the dealer where the vehicle was diagnosed with a failure to the frontal impact sensor. The contact was informed that the frontal impact sensor needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 112,000. The VIN was not available.

- Pleasant Prairie, WI, USA

The brakes kept grinding and squealing even after we changed them, next the rotors and calipers were done. Then again one by one everything needed to be replaced and still didn't take and we kept smelling burning coming from the tires. We then replaced the master cylinder and the brake lines and still it won't take. I looked it up and there are countless complaints on this and Chrysler/Jeep do nothing about this huge safety risk ! Answers to your questions 1. Braking system as a whole and yes it can't move 2. If you do not have brakes in a vehicle you cannot stop so unsafe for the driver and everyone on the road bc of collision. 3. Yes my mechanic has re done this job multiple times and agrees there is a defect going on, not normal. 4. I did not know I needed my insurance or the police involved, the dealership is a joke. 5. No warning sensors or a heads up, just does it.

- Bradenton, FL, USA

Dear Sir(or Madam), My Driver Side Rear Cailper locked up (AGAIN) and my Rear Brakes, Cailper and Rotors had to be replaced (AGAIN) this is the second time I had this problem since I purchased this Jeep that I had the Cailper locked up. Jeep has a real problem with this happening. The last time this happened I had a warranty this time I don't. The last 3 Wranglers I have purchased had the same problem, if this isn't a safety problem it shoud be. I have not received a Repair Order as of yet but will summit it when I do get it.

- Kane, PA, USA

2017 Jeep Wrangler Unlimited with 44,000 rear brake calipers sticking and burning smell. Had brake pads and calipers replaced on all 4 wheels. At approx 60K miles, rear brakes were sticking and smoking. Right brakes wearing unevenly compared to the left side, both front and rear. Caliper seals are leaking. Replaced 4 brake hoses, Calipers and Pads AGAIN. At 70K miles rear brakes locked up and caused a fire on the rear passenger wheel which created unsafe driving conditions with 2 small children on board. I had to stop on the side of a 2 lane road with small shoulder, quickly evacuate the children onto the shoulder of the road and extinguish the fire using an on-board suppression device. We then had to wait for towing assistance on the side of the road for 90 minutes. Brakes, Hoses, Calipers replaced all around. Again.

- Bel Air, MD, USA

2017 Jeep Wrangler, approx 46k miles, driven gently (only highway and city), well-maintained. Problems with Brake Calipers seizing. Back Driver calipers/lines/pad/etc replaced. ABS and brakes jammed last week. Front and Back Passenger calipers, rotors, brake fluid lines and brake pads advised by mechanic. Brakes temping 550 - unreadable (temp gun wouldn't register) Mechanic recommends unsafe to drive because brakes could seize and cause sudden stop and/or accident Dealer says too bad, normal wear and tear. This is our family's 10th Jeep, and NOTHING has happened like this before. Seems like a safety issue perhaps that Jeep should be addressing rather than putting on the consumer (who will no longer purchase Jeeps)

- Columbia, MD, USA

A check engine light came on and when diagnosed it was the Electronic Vacumn Pump which runs the braking system. I see there is a TSB from FCA (Fiat Chrysler Automobiles) about this problem.. Case Number: S1805000006 Release Date: 02/24/2020 Symptom/Vehicle Issue: ESC Light Illuminated. DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE Discussion: If ABS has C1252-92 Active or Stored do not replace the brake system module (ABS). PCM may also have set P258B-00. The faults are pointing to vacuum pump system having an issue maintaining vacuum levels. Please check the vacuum pump operation, fusing, wiring, and connector for proper functionality. Poor connections, spread pins, damaged connectors are possible causes. Perform the diagnostic for the DTC P258B regardless if it is set or not, since it is more compressive of a test than C1252-92. In addition when checking Vacuum lines, please ensure to check Vacuum hoses and check valves between the engine intake, booster and vacuum pump. Because the check valves only allow flow of air on one direction, each vacuum circuit must be checked separately to make sure there are no leaks, kinks or damages. Please refer to the correct vacuum diagram. For KL vehicles: inspect ALL under hood grounds for connection and contact issues. My Jeep is at the Ford Dealership I work at at this time. Didn't want to drive any farther than I had to at this time.

- Kane, PA, USA