2016 Mazda CX-3
TSBs (Technical Service Bulletins)
Technical Service Bulletins (TSBs) for the 2016 CX-3 are official communications between Mazda & their dealerships that describe processes for troubleshooting or fixing certain common problems. All vehicle manufacturers are required by U.S. law to make their TSBs available to the public.
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #06-002-23
Some vehicles may exhibit a light resistance and/or an unusual noise when turning the steering wheel in either direction. This concern may be caused by insufficient lubrication between the worm wheel gear and worm shaft. Read More »
-
TSB #06-001-23a
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
-
TSB #06-001-23
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
-
TSB #02-003-22
Some customers may complain that the steering wheel is off center more than 3??A? even when driving straight on a flat road. Read More »
-
TSB #00-001-22
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #06-001-21-3765b
Light Resistance and/or Unusual Noise When Turning Steering Wheel Left or Right: Some vehicles may exhibit a light resistance and/or an unusual noise when turning the steering wheel in either direction. Read More »
-
TSB #06-001-21-3765a
Some vehicles may exhibit a light resistance and/or an unusual noise when turning the steering wheel in either direction. This concern may be caused by the following causes. Read More »
-
TSB #06-002-21-3782
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
-
TSB #02-003-21-3777
Some customers may complain that the steering wheel is off center more than 3??A? even when driving straight on a flat road. Read More »
-
TSB #00-001-21-3768
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #06-001-21-3765
Some vehicles may exhibit a light resistance and/or an unusual noise when turning the steering wheel in either direction. This concern may be caused by insufficient lubrication of the gear due to uneven and deteriorated grease. Read More »
-
TSB #06-004-20-3757
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
-
TSB #06-001-20-3676
Some vehicles may exhibit a light resistance and/or an unusual noise when turning the steering wheel in either direction. This concern may be caused by insufficient lubrication of the gear due to uneven and deteriorated grease. Read More »
-
TSB #02-003-20-3677
Some customers may complain that the steering wheel is off center more than 3??A? even when driving straight on a flat road. Customers having this concern should have their vehicle repaired using the following repair procedure. Read More »
-
TSB #06-005-19-3610
Some vehicles may exhibit a light resistance and/or an unusual noise when turning the steering wheel to the left. This concern may be caused by insufficient lubrication of the gear due to uneven and deteriorated grease. Read More »
-
TSB #06-004-19-3591
Some customers may find a piece of aluminum tape and/or black liquid on the driver side floor. The aluminum tape may have dropped from the bottom of the steering column and the black liquid is grease that has melted and dripped onto the ... Read More »
-
TSB #06-002-19-3585a
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
-
TSB #02-004-19-3574
Some customers may complain that the steering wheel is off center more than 3? even when driving straight on a flat road. Read More »
-
TSB #MT-012-18
If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. Read More »
-
TSB #06-002-18-3504
Some vehicles may exhibit a light resistance and/or an unusual noise when turning the steering wheel to the left. This concern may be caused by insufficient lubrication of the gear due to uneven and deteriorated grease. Read More »
-
TSB #02-003-17-3300c
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
-
TSB #06-002-16-3194
SOME VEHICLES MAY EXHIBIT AN UNUSUAL NOISE FROM AROUND THE DRIVER?S FOOT AREA WHEN REPEATEDLY TURNING THE STEERING WHEEL TO THE LEFT OR RIGHT. A VIBRATION IS FELT AT THE STEERING WHEEL WHEN THE NOISE OCCURS. Read More »
-
TSB #02-010-16-3170
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
-
TSB #02-009-16-3155
SOME CUSTOMERS MAY COMPLAIN THAT THE STEERING WHEEL IS OFF CENTER MORE THAN 3? EVEN WHEN DRIVING STRAIGHT ON A FLAT ROAD. Read More »
-
TSB #02-009-16-3155
Some customers may complain that the steering wheel is off center more than 3" even when driving straight on a flat road. Read More »
-
TSB #02-003-15-2990A
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
-
TSB #06-001-23
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
-
TSB #06-002-19-3585a
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
-
TSB #02-010-18-3477
Some customers may complain that the steering wheel is off center more than 3? even when driving straight on a flat road. Read More »
-
TSB #06-001-17-3307b
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
-
TSB #06-001-17-3307a
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance.This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
-
TSB #02-009-16-3155
SOME CUSTOMERS MAY COMPLAIN THAT THE STEERING WHEEL IS OFF CENTER MORE THAN 3? EVEN WHEN DRIVING STRAIGHT ON A FLAT ROAD. Read More »
-
TSB #02-004-22a
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #02-004-22
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #02-002-20-3651
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #02-005-19-3503a
Some vehicles may experience a creaking noise from the front shock absorber when going over bumps. Upon inspection, the coil spring is found to be broken at the lower part without any trace of an accident. Read More »
-
TSB #02-003-19-3547
Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage. Read More »
-
TSB #02-001-19-3550
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #02-013-18-3491
Some vehicles may exhibit a crack on the front shock absorber dust boot (1). This may be caused by the dust boot having insufficient resistance to the cold. Read More »
-
TSB #02-005-18-3444
Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage. Read More »
-
TSB #02-003-17-3300c
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
-
TSB #02-003-17-3300a
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
-
TSB #07-004-16
Auto A/C blows warm air Read More »
-
TSB #02-014-16-3235
SOME VEHICLES MAY EXHIBIT OIL SEEPAGE FROM THE REAR SHOCK ABSORBER(S) WHILE THE VEHICLE IS ON A HOIST (I.E. DURING NORMAL MAINTENANCE OR OTHER SERVICE). Read More »
-
TSB #02-010-16-3170C
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
-
TSB #02-010-16-3170C
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
-
TSB #02-010/16
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
-
TSB #02-010-16-3170
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
-
TSB #02-005-16-3152A
BEGINNING WITH THE CX-5 AND MAZDA6 MODELS, GRIP TYPE FRONT AND REAR STABILIZER BUSHINGS HAVE BEEN INCORPO-RATED FOR NOISE PREVENTION PURPOSES. Read More »
-
TSB #02-010-16-3170
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
-
TSB #02-005-16-3152A
BEGINNING WITH THE CX-5 AND MAZDA6 MODELS, GRIP TYPE FRONT AND REAR STABILIZER BUSHINGS HAVE BEEN INCORPO-RATED FOR NOISE PREVENTION PURPOSES. Read More »
-
TSB #02-005-19-3503a
Some vehicles may experience a creaking noise from the front shock absorber when going over bumps. Upon inspection, the coil spring is found to be broken at the lower part without any trace of an accident. Read More »
-
TSB #02-014-18-3503
Some vehicles may experience a creaking noise from the front shock absorber when going over bumps. Upon inspection, the coil spring is found to be broken at the lower part without any trace of an accident. Read More »
-
TSB #02-006-18-3449
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #02-002-18-3300d
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving onrough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
-
TSB #02-003-17-3300b
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
-
TSB #02-003-17-3300a
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
-
TSB #02-010-16-3170
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
-
TSB #02-010-16-3170
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
-
TSB #02-003/15
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #02-003-15-2990A
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
-
TSB #02-003-17-3300a
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
-
TSB #SA-006-22
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #SA-016-19
There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #02-006-18-3449
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #SA-003-23a
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #SA-003/23
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #00-002-19-3561
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. Read More »
-
TSB #04-002-19-3545
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #00-003-18-3480
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAOauthorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program. Read More »
-
TSB #04-004-18-3468
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #MT-019-17
WARNING: DO NOT PERFORM OPERATIONAL TESTING OF THE SMART CITY BRAKE SUPPORT (SCBS) SYSTEM. If the warning indicator light is not illuminated and there are no codes stored in the system, the system is operating properly, and Mazda cannot ... Read More »
-
TSB #SA-052-17
Smart City Brake Support (SCBS) frequently asked questions (FAQ) Read More »
-
TSB #02-001-17
TPMS WARNING LIGHT ON - Some vehicles may experience a Tire Pressure Monitoring System (TPMS) warning light on when driving on a smooth road surface even if the TPMSF system has been properly initialized at the specified tire air pressure. Read More »
-
TSB #1079M
IN CERTAIN CONDITIONS, SMART CITY BRAKE SUPPORT (SCBS) MAY OPERATE UNINTENTIONALLY. THE OWNER'S MANUAL PROVIDES 7 EXAMPLES: OBJECTS ON THE ROAD AT THE ENTRANCE TO A CURVE.VEHICLES PASSING IN THE OPPOSITE LANE WHILE MAKING A CURVE. Read More »
-
TSB #1079M
IN CERTAIN CONDITIONS, SMART CITY BRAKE SUPPORT (SCBS) MAY OPERATE UNINTENTIONALLY. THE OWNER'S MANUAL PROVIDES 7 EXAMPLES: OBJECTS ON THE ROAD AT THE ENTRANCE TO A CURVE.VEHICLES PASSING IN THE OPPOSITE LANE WHILE MAKING A CURVE. Read More »
-
TSB #04-004-16-3160
SOME VEHICLES EXHIBIT BRAKE RELATED CONCERNS SUCH AS BRAKE NOISE, BRAKE JUDDER OR BRAKE DRAGGING. IF YOU ENCOUNTER A CUSTOMER COMPLAINT FOR ANY ONE OF THESE SYMPTOMS, REFER TO THE FOLLOWING INFORMATION TO UNDERSTAND WHY SYMPTOMS MAY ... Read More »
-
TSB #SA-016-24
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-010-23
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #SA-078-22
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #00-001-22
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #00-001-20-3689
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-019-20
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may ... Read More »
-
TSB #04-005-19-3512
Some vehicles may exhibit a rattle / knock noise from the front disc brake caliper (1) when driving on a rough road surface. Read More »
-
TSB #09-010-19-3624
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #00-003-18-3480a
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. Read More »
-
TSB #04-002-17-3316b
Some vehicles may exhibit a squeak noise when applying the brakes and/or groove marks (A) on the front disc plates. Read More »
-
TSB #04-002-17-3316a
Some vehicles may exhibit a squeak noise when applying the brakes and/or groove marks (A) on the front disc plates. Read More »
-
TSB #04-002-17
Squeak noise from front brakes and/or groove marks on front disc plate Read More »
-
TSB #04-005-19-3512
Some vehicles may exhibit a rattle / knock noise from the front disc brake caliper (1) when driving on a rough road surface. Read More »
-
TSB #04-001-19-3556
Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. Read More »
-
TSB #04-004-15-3099
SOME VEHICLES MAY EXHIBIT A SQUEAK NOISE WHEN APPLYING THE BRAKES AND/OR GROOVE MARKS (A) ON THE FRONT DISC PLATES. Read More »
-
TSB #05-003-20-3725
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #07-007-19-3638
Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a plugged heater core. Read More »
-
TSB #01-008-19-3568
Some customer using "Flexible" setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. Read More »
-
TSB #01-007-19-3541
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of ... Read More »
-
TSB #01-003-19-3557
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. Read More »
-
TSB #MT-008-18
Some customers may complain about: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator, light flashing, Battery discharge, Electrical relay buzzing noise. Read More »
-
TSB #MT-007-18
ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. Read More »
-
TSB #MT-008-18
ENGINE NO START (KEY NOT DETECTED): Some customers may complain about the following: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing. Read More »
-
TSB #01-012-18-3474
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. Read More »
-
TSB #SA-026-18
If a vehicle is driven on extremely short trips most of the time (where the engine never reaches normal operating temperature), the engine oil may become diluted with fuel and the engine oil level will increase. Read More »
-
TSB #01-006-18-3429
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of ... Read More »
-
TSB #MT-021-17
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. Read More »
-
TSB #05-005-16-3218
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738).?P0842:00 - OIL PRESSURE SWITCH NO. Read More »
-
TSB #05-005-16-3218
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738).?P0842:00 - OIL PRESSURE SWITCH NO. Read More »
-
TSB #1080M
IF AN ENGINE ASSEMBLY IS REPLACED AFTER A CATASTROPHIC INTERNAL MECHANICAL FAILURE, CLEAN THE INTAKE MANIFOLD INTERNALLY BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. Read More »
-
TSB #1080M
IF AN ENGINE ASSEMBLY IS REPLACED AFTER A CATASTROPHIC INTERNAL MECHANICAL FAILURE, CLEAN THE INTAKE MANIFOLD INTERNALLY BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. Read More »
-
TSB #01-009-16-3172B
SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE CHECK ENGINE LIGHT ON AND DTC P0015 / P0524 STORED IN MEMORY. Read More »
-
TSB #01-009-16-3172B
SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE CHECK ENGINE LIGHT ON AND DTC P0015 / P0524 STORED IN MEMORY. Read More »
-
TSB #1102M
WORKSHOP MANUAL EVAP SYSTEM LEAK INSPECTION USING THE M-MDS HAS BEEN DISCONTINUED FOR SOME MODELS. INSTEAD, THE WORKSHOP MANUAL EVAP SYSTEM LEAK INSPECTION USING EVAP LEAK TESTER WILL BE USED TO TROUBLESHOOT EVAP SYSTEM LEAKS. Read More »
-
TSB #RF-16-03
THE 2016 CX-9 WITH THE SKYACTIV?-G 2.5T ENGINE REQUIRES A UNIQUE OIL FILTER (PY8W-14-302) WHICH IS NOT INTERCHANGEABLE WITH OTHER SKYACTIV? OIL FILTERS. THE UNIQUE OIL FILTER CAN BE IDENTIFIED WITH TWO WHITE BANDS AS SHOWN BELOW. Read More »
-
TSB #01-014-15-3055A
FREQUENT ENGINE STARTS UNDER EXTREMELY COLD AMBIENT TEMPERATURES MAY RESULT IN OIL SEEPAGE FROM THE ENGINE OIL PRESSURE SWITCH. THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. Read More »
-
TSB #0904415
Mazda connect shuts down and does not reboot Read More »
-
TSB #01-018-15-3070
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P2610 AND P2507 STORED IN MEMORY AFTER ENGINE START AND ROOM FUSE 15A (A) REMOVED. Read More »
-
TSB #01-014-15-3055
FREQUENT ENGINE STARTS UNDER EXTREMELY COLD AMBIENT TEMPERATURES MAY RESULT IN OIL SEEPAGE FROM THE ENGINE OIL PRESSURE SWITCH. THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. Read More »
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-032-23a
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #01-008-23
Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. Read More »
-
TSB #SA-035-23
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
-
TSB #SA-032-23
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #SA-010-23
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #RF-23-01
When servicing SKYACTIV engine vehicles requiring to replace the Oil Galley Plug and Crush Washer, order the required part numbers below. Read More »
-
TSB #MT-004-22
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. Read More »
-
TSB #SA-065-22
Some vehicles equipped with a coolant control valve may exhibit difficulties when refilling the coolant because the control valve is closed and air in the engine cannot escape during ignition ON. Read More »
-
TSB #01-012-22
Some vehicles may exhibit accumulation of dried coolant (1) around the water pipe (2). This is caused by a gap between the housing and pipe due to a press fitting during the manufacturing process. Read More »
-
TSB #00-001-22
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #MT-002-21
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. Read More »
-
TSB #SA-047-21
If you receive a customer concern about the CHECK ENGINE light coming on and DTC P3400 (cylinder deactivation system malfunction) stored, the cylinder deactivation oil control valve may be plugged with plastic debris from the oil filter ... Read More »
-
TSB #01-006-21-3779a
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #MT-002-21
When programming a key or installing a Genuine Mazda Accessory Remote Engine Start system, you may encounter programming difficulty. Read More »
-
TSB #MT-001-21
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #CSP05c
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
-
TSB #CSP05d
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
-
TSB #01-003-21-3776
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. Read More »
-
TSB #00-001-21-3768
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #CSP05b
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #CSP05a
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #MT-005-20
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Read More »
-
TSB #CSP05
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #SA-071-20
Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. Read More »
-
TSB #00-001-20-3689
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-009-20
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. Read More »
-
TSB #MT-002-19
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
-
TSB #01-022-19-3657
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
-
TSB #SA-053-19
GUIDE LINES AND PHOTOS TO DETERMINE IF FLUID/OIL SEEPAGE OR LEAK IS SEVERE ENOUGH TO REQUIRE WARRANTY REPAIR OR TO CLEAN AND MONITOR. Read More »
-
TSB #01-019-19-3628
Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. Read More »
-
TSB #SA-049-19
Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint: ??A?A? MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE ??A?A? CANNOT COMMUNICATE WITH ... Read More »
-
TSB #MT-004-19
Some customers may complain about: ??A?A? Intermittent engine no start ??A?A? Instrument cluster red security indicator light ON ??A?A? Engine Start/Start Button Amber indicator light flashing ??A?A? Battery discharge ??A?A? Electrical ... Read More »
-
TSB #MT-003-19
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Read More »
-
TSB #MT-002-19
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
-
TSB #SA-040-19
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
-
TSB #01-016-19-3627
Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. Read More »
-
TSB #00-003-19-3583
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
-
TSB #07-001-19-3465a
Some customers may complain about warm air from the climate control vents when the air conditioner is ON. This may be caused by condenser corrosion, causing a refrigerant leak. Read More »
-
TSB #01-005-19-3548
Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak). Read More »
-
TSB #01-004-19-3558
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Read More »
-
TSB #MT-009-18
If an oil pressure inspection is needed on a SKYACTIV-G engine, use the Special Service Tool (SST) set shown below and refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2. Read More »
-
TSB #MT-009-18
If an oil pressure inspection is needed on a SKYACTIV-G engine, use the Special Service Tool (SST) set shown below and refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2. Read More »
-
TSB #SA-029-18
IMPORTANT: If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Read More »
-
TSB #05-004-18-3466
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. Read More »
-
TSB #04-003-18-3455
Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. Read More »
-
TSB #01-002-17-3299a
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of ... Read More »
-
TSB #0100116
Engine Start /Stop Procedure with room fuse removed Read More »
-
TSB #0101415
Engine Oil seepage from engine oil pressure switch Read More »
-
TSB #01-016-18-3522
On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Read More »
-
TSB #01-013-18-3478
Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak)The concern is most likely the result of the customer not getting the fuel cap completely ... Read More »
-
TSB #01-006-18-3429
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of ... Read More »
-
TSB #01-005-18-3415
Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. Read More »
-
TSB #01-002-17-3299a
When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of ... Read More »
-
TSB #MT-002-19
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
-
TSB #MT-003/22
Some customers may complain about a tapping or knocking noise coming from the rear seat after fuel fill. Read More »
-
TSB #MT-002-21a
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. Read More »
-
TSB #MT-004-20
Some customers may complain about a tapping or knocking noise coming from the rear seat after fuel fill. Read More »
-
TSB #00-003-19-3583
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
-
TSB #MT-001-19
Some customers may complain about a tapping or knocking noise coming from the rear seat after fuel fill. Read More »
-
TSB #01-005-18-3415
Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. Read More »
-
TSB #00-003-19-3583
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
-
TSB #MT-002-21a
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. Read More »
-
TSB #RF-16-03R1
The SKYACTIV?-G 2.5T engine requires a unique oil filter (PY8W-14-302) which is NOT interchangeable with other SKYACTIV? oil filters. The unique oil filter can be identified with two white bands as shown below. Read More »
-
TSB #PF-24-03
Due to limitations, certain vehicles from 2016 to current models might display an inaccurate transmission part number in the Global Electronic Parts Catalog (GEPC). Read More »
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #05-002-23
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #SA-068-22
The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. Read More »
-
TSB #01-010-22
Some customers may experience a squeaking noise may be heard from the exhaust manifold when the idle speed drops from fast idle to normal idle speed during cold start. This is caused by a variable valve being stuck in the closed position. Read More »
-
TSB #SA-038-22
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. Read More »
-
TSB #SA-006-22a
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #SA-006-22
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #00-001-22
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-009-22
The new AWD rear differential DOES NOT come with a breather cap on the rear of the differential, therefore a new one will need to be ordered and installed when replacing the differential. Read More »
-
TSB #05-001-21-3826
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. Read More »
-
TSB #SA-032-21
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #Transmission
MultiModel (equipped with skyactivdrive) ATF color deterioration New vehicle automatic transmission fluid (ATF) color is blue. As the vehicle mileage increases, the ATF color changes. The color change does not affect vehicle performance. Read More »
-
TSB #00-001-21-3768
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #05-005-20-3752
Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. Read More »
-
TSB #05-003-20-3725
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #SA-053-20
When replacing manual or automatic transmission, make sure to remove the plug from the old transmission (as shown below) and then re-install it to the new transmission with a new washer. Read More »
-
TSB #00-001-20-3689
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-030-20
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. NOTE: The following Caution is included with every ATX that requires configuration. Read More »
-
TSB #SA-058-19
WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the ... Read More »
-
TSB #SA-053-19
GUIDE LINES AND PHOTOS TO DETERMINE IF FLUID/OIL SEEPAGE OR LEAK IS SEVERE ENOUGH TO REQUIRE WARRANTY REPAIR OR TO CLEAN AND MONITOR. Read More »
-
TSB #05-004-19-3466
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. Read More »
-
TSB #05-002-19-3576
Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. Read More »
-
TSB #01-014-18-3487
Some customer using "Flexible" setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. Read More »
-
TSB #05-002-18-3454
The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use"ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. Read More »
-
TSB #MTI_1138
Multi-Model - Clutch Slippage or Smell after Clutch Disc Replacement Read More »
-
TSB #05-005-16-3218
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738).?P0842:00 - OIL PRESSURE SWITCH NO. Read More »
-
TSB #05-002-16-3129
THE NEW SKYACTIV-DRIVE FW6A-EL AT USES ?AUTOMATIC TRANSMISSION FLUID (ATF) TYPE: FZ?. ONLY USE ?ATF-FZ? TO FILL OR TOP OFF THE FLUID LEVEL. ATF-FZ IS SPECIALLY DESIGNED FOR USE IN THE SKYACTIV-DRIVE SERIES AT. Read More »
-
TSB #05-002-23
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #SA-038-22
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. Read More »
-
TSB #01-008-19-3568a
Some customer using ??A???A???A?Flexible??A???A???A? setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. Read More »
-
TSB #01-008-19-3568
Some customer using "Flexible" setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. Read More »
-
TSB #0500215
Check Engine light and A/T Warning light on with one or more of these DTS (P0842, P0847, P0872, P0877, P0780, P1738) Stored in TCM Memory Read More »
-
TSB #SA-038-22
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. Read More »
-
TSB #03-002-18-3505a
Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. Read More »
-
TSB #03-001-19-3505b
Some vehicles may exhibit a squeak noise from the right front driveshaft at the automatic transaxle when driving. Read More »
-
TSB #03-002-18-3505a
Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. Read More »
-
TSB #03-002-18-3505
Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. Read More »
-
TSB #SA-009-22
The new AWD rear differential DOES NOT come with a breather cap on the rear of the differential, therefore a new one will need to be ordered and installed when replacing the differential. Read More »
-
TSB #05-002-19-3576
Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. Read More »
-
TSB #SA-037-18
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. Read More »
-
TSB #07-003-24
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10 A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
-
TSB #SA-008-24
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-032-23a
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #00-001-23
In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on an ??A?A?as-needed??A?A? basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. Read More »
-
TSB #SA-032-23
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #SA-033-23
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #09-016-23
Speedometer replacement procedure Read More »
-
TSB #SA-010-23
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #07-002-23
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
-
TSB #SA-041-22c
Some customers may complain about infotainment center display: * Ghost Touch * DTC B108E:04 may be stored (Touch screen operates by itself) * Surface Peeling * DTC B108E:04 may be stored * Spider Cracks * White ... Read More »
-
TSB #09-018-22b
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.324 or later). The system performance has been improved as follows: Ver. 74.00. Read More »
-
TSB #22-01R
Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors. Read More »
-
TSB #SA-075-22
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #SA-074-22
Some customers may complain the HVAC system not maintaining the correct temperature or the ambient (outside) temperature reading incorrectly. This is caused by a failure in the ambient temperature sensor. Read More »
-
TSB #SA-066-22
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: * C1001:92 - Forward sensing camera (FSC) poor field of ... Read More »
-
TSB #09-041-22
If the right-side Blind Spot Monitoring (BSM) control module is replaced for any reason, it is also necessary to replace the left-side BSM control module in order to complete the radar aiming procedure. Read More »
-
TSB #RF-22-01
Some customers may complain about infotainment center display ghost touch (touch screen operates by itself), surface peeling or spider cracks. Repair kits are available to replace just the screen. Read More »
-
TSB #SA-041-22c
Some customers may complain about infotainment center display: - Ghost Touch (Touch screen operates by itself) - Spider Cracks - Surface Peeling - White dots Read More »
-
TSB #SA-001-22d
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #01-006-22
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #09-018-22
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.311 or later). Read More »
-
TSB #SA-001-22c
Use the symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-005-22a
Some customers may experience a continuous infotainment reboot in or near Seattle Washington and troubleshooting is not possible due to continuous reboot. Read More »
-
TSB #SA-026-22
Apple CarPlay / Android Auto Frequently Asked Questions (FAQs) Read More »
-
TSB #SA-001-22c
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #01-003/22
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #SA-001-22
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-005-22
Some customers may experience a continuous infotainment reboot in or near Seattle Washington. Mazda is aware of the issue and is working on a resolution. Read More »
-
TSB #SA-001/22
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
-
TSB #01-006-21-3779b
Battery Maintenance: This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #SA-052-21
For improvement of electrical diagnosis, the SKYACTIV??A? Wiring Terminal Test Kits has been delivered all the dealers. Read More »
-
TSB #SA-019-21d
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-019-21c
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-046-21
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #SA-019-21a
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-029-21a
APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
-
TSB #09-017-21-3808
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black under any temperature. Read More »
-
TSB #MT-002-21
When programming a key or installing a Genuine Mazda Accessory Remote Engine Start system, you may encounter programming difficulty. Read More »
-
TSB #MT-001-21
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #08-002-21-3788
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. DTC B00A0:09 (Occupant classification sensor internal signal output unstable). Read More »
-
TSB #MT-001-21
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #01-005-21-3778
The Mazda DCA-8000PM is required for all warranty battery testing. If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #01-006-21-3779
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #01-003-21-3776
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. Read More »
-
TSB #09-002-21-3770
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer Read More »
-
TSB #MT-006-20
Some customers may complain about the following MAZDA CONNECT??A?A? Temperature Warning message: ??A?A? Display is too Hot. Screen performance may be decreased until it cools. Read More »
-
TSB #09-036-20-3756
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH??A? hands-free unit or text messaging related concerns. Read More »
-
TSB #SA-070-20
APPLE CARPLAY / ANDROID AUTO FREQUENTLY ASKED QUESTIONS (FAQ): NOTE: The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
-
TSB #SA-063-20
When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage. Read More »
-
TSB #MT-001-20
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #08-001-20-3696a
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. ??A?A? DTC B00A0:09 (Occupant classification sensor internal signal output unstable). Read More »
-
TSB #09-015-20-3698b
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. Read More »
-
TSB #09-015-20-3698
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. Read More »
-
TSB #SA-041-20
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #SA-011-20a
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
-
TSB #01-002-20-3678
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. Read More »
-
TSB #SA-009-20
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. Read More »
-
TSB #SA-011-20
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
-
TSB #09-003-20-3671
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #SA-049-19
Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint: ??A?A? MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE ??A?A? CANNOT COMMUNICATE WITH ... Read More »
-
TSB #MT-004-19
Some customers may complain about: ??A?A? Intermittent engine no start ??A?A? Instrument cluster red security indicator light ON ??A?A? Engine Start/Start Button Amber indicator light flashing ??A?A? Battery discharge ??A?A? Electrical ... Read More »
-
TSB #07-007-19-3638
Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a plugged heater core. Read More »
-
TSB #09-010-19-3624
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #09-031-19-3625
After the installation of a new instrument cluster, the message "Fctry" or ??A???A???A?Factory??A???A???A? is displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Read More »
-
TSB #SA-031-19
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #SA-029-19
Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. Read More »
-
TSB #09-022-19-3599
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #SA-006-19a
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #01-008-19-3568a
Some customer using ??A???A???A?Flexible??A???A???A? setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. Read More »
-
TSB #SA-001-19b
APPLE CARPLAY??A?A? / ANDROID AUTO??A?A? FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #SA-001-19a
APPLE CARPLAY??A?A? / ANDROID AUTO??A?A? FREQUENTLY ASKED QUESTIONS (FAQ). Many frequently asked question and the answers. Read More »
-
TSB #09-010-19-3577
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #SA-006-19
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #01-006-19-3549
The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazda models, there is no key cylinder on the steering column. Read More »
-
TSB #01-001-19-3551
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #01-002-19-3552
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #SA-047-18
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #MT-002-18
Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth? and the same device is also connected to the USB port for charging. Read More »
-
TSB #MT-010-18
Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. Read More »
-
TSB #MT-011-18
SMS (Short Message Service) messages received by paired phones (Android and iPhone 5 iOS 7.0 or higher) can be downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. Read More »
-
TSB #MT-010-18
Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. Read More »
-
TSB #MT-004-18
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #MT-007-18
Some customers may complain about the following: Engine no start. A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g. Read More »
-
TSB #MT-008-18
Some customers may complain about: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator, light flashing, Battery discharge, Electrical relay buzzing noise. Read More »
-
TSB #09-035-18-3509
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #SA-036-18
MAZDA MOBILE START (MMS) APP ERROR MESSAGE INSTALLED ON ANDROID DEVICES: Customers may get an error message "Device no longer has access or service." for the MMS APP installed on android devices starting 8/1/18. Read More »
-
TSB #MT-004-18
ELECTRICAL CONCERN AND/OR MULTIPLE DTC'S DUE TO AFTERMARKET DEVICE: If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored... Read More »
-
TSB #MT-007-18
ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. Read More »
-
TSB #09-010-18-3440a
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.546 or later). NOTE: For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #09-008-18-3416a
Some vehicles may exhibit the active driving display opening/closing improperly as described below: It does not open or close when the ignition is turned ON or OFF. The display operation does not fully open/close. Read More »
-
TSB #MT-004-18
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
-
TSB #09-008-18-3416
Some vehicles may exhibit the active driving display opening/closing improperly as described below: It does not open or close when the ignition is turned ON or OFF. The display operation does not fully open/close. Read More »
-
TSB #MT-002-18
Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth? and the same device is also connected to the USB port for charging. Read More »
-
TSB #MT-001-18
When installing a navigation SD card, the center display may show error message "Invalid SD Card". This may be caused by: The navigation SD card lock tab is locked.The navigation SD card has a VIN mismatch due to SD card swapping. Read More »
-
TSB #00-003-17-3406
In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on a "as-needed" basis, aSpecial Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. Read More »
-
TSB #01-001-17
Some vehicles may experience the CHECK ENGINE LIGHT OIN with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A removed * P2610 Instrument cluster internal engine off timer performance problem * P2507 PCM battery ... Read More »
-
TSB #MT-019-17
WARNING: DO NOT PERFORM OPERATIONAL TESTING OF THE SMART CITY BRAKE SUPPORT (SCBS) SYSTEM. If the warning indicator light is not illuminated and there are no codes stored in the system, the system is operating properly, and Mazda cannot ... Read More »
-
TSB #MT-017-17
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
-
TSB #15-005-17-3358b
Some customers may complain that the BSM indicator light on the outer mirror glass does not illuminate when: ? Customer vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area. Read More »
-
TSB #15-005-17-3358a
Some customers may complain that when passing a vehicle slowly, even if the vehicle is still in the alert area, the BSM indicator light on the outer mirror glass does not illuminate. Read More »
-
TSB #02-003-17-3300c
Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving on rough roads and/or when turning the steering wheel while the vehicle is stopped. Read More »
-
TSB #09-017-17-3347c
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502 or later). NOTE: For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #09-001-17-3296b
When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. Read More »
-
TSB #15-005-17-3358
Some customers may complain that when passing a vehicle slowly, even if the vehicle is still in the alert area, the BSM indicator light on the outer mirror glass does not illuminate. Read More »
-
TSB #SA-048-17
In order to do a CMU data retrieval for the new MAZDA CONNECT software, make sure to use version 31 (available on MGSS). Read More »
-
TSB #09-019-17
Fctry MESSASGE DISPLAYED after instrument cluster replacement. After the installation of a new instrument cluster, the message "Fctry" is displayed instead of the odometer. Some new instrument clusters are in the factory mode setting. Read More »
-
TSB #09-018-17
Display shows inaccurate ambient temperature. Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature. Read More »
-
TSB #MT-010-17
Some customers may claim that it is impossible or difficult to view the Active Driving Display, even if the position of the display is adjusted through the Settings screen. Read More »
-
TSB #MT-010-17
Active driving display caution (Update) Read More »
-
TSB #15-003-17
LDWS AND HBC WARNING LIGHTS ON AND DTC C1001:92 Read More »
-
TSB #09-002-17
Rust around rear view camera and/or liftgate opener switch Read More »
-
TSB #SA266
MAZDA Mobile start (MMS) cannot communicate with vehicle Read More »
-
TSB #09-062-16
Active driving display opens/closes improperly. Some vehicles may exhibit the active driving display opening/closing improperly as described below: * It does not open or close when the ignition is turned ON or OFF . Read More »
-
TSB #09-061-16
Fctry MESSAGE DISPLAYED AFTER INSTRUMENT CLUSTER REPLACEMENT. After the installatioin of a new instrument cluster, the message "F ctry" IS DISPLAYED INSTEAD OF THE ODOMETER. Some new instrument clusters are in the factory mode setting. Read More »
-
TSB #00-005-16-3245
IN SUPPORT OF THE NEW MAZDA MX-5 AND CX-3, MAZDA WILL MAKE AVAILABLE FOR LOAN ON A ?AS-NEEDED? BASIS, A SPE-CIAL SERVICE TOOL (SST) TO ALLOW FOR THE RADAR AIMING OF THE BLIND SPOT MONITORING (BSM) SYSTEM. Read More »
-
TSB #1096M
IF THE ACTIVE DRIVING DISPLAY (AD-DISP) UNIT REQUIRES REMOVAL, USE CAUTION WHEN DISCONNECTING/CONNECTING THE WIRING HARNESS. IF THE HARNESS IS NOT CONNECTED PROPERLY, THE AD-DISP MAY NOT OPERATE. Read More »
-
TSB #SA299
SOME VEHICLES MAY HAVE DTC C1001:92 STORED IN MEMORY. DTC C1001:92 SETS AS A PAST RECORD FOR LOW VISIBILITY OF THE FORWARD SENSING CAMERA (FSC). IT DOES NOT MEAN THERE IS AN ACTUAL FSC DEFECT. Read More »
-
TSB #SA296
SOME CUSTOMERS MAY REPORT THAT WHEN USING THEIR IPHONE WITH BLUETOOTH AUDIO THAT THEY CANNOT SELECT A NEW SONG OR A DIFFERENT SONG WILL PLAY. Read More »
-
TSB #SA288
IF YOU ENCOUNTER A VEHICLE WITH DTC P0137 (CIRCUIT LOW INPUT), CHECK THE REAR HARNESS AT THE RED CIRCLED AREA IN THE FOLLOWING DIAGRAM. Read More »
-
TSB #1099M
WHEN REPROGRAMMING A CONTROL MODULE, ALWAYS USE THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE. IF NOT USED, THE CONTROL MODULE REPROGRAMMING MAY FAIL DUE TO A WEAK VEHICLE BATTERY. Read More »
-
TSB #SA266
IF A CUSTOMER HAS A VEHICLE COMMUNICATION RELATED ERROR ON THEIR APP, PERFORM THE FOLLOWING: DISCONNECT THE BATTERY OR UNPLUG THE MODULE FOR AT LEAST 10 SECONDS. Read More »
-
TSB #SA285
OVER THE PAST TWO WEEKS, AN INCREASING NUMBER OF IPHONE SE EARLY ADOPTERS HAVE REPORTED AUDIO ISSUES WITH BLUETOOTH PHONE CALLS WHEN THE SMARTPHONE IS PAIRED WITH A VEHICLE OR WIRELESS HEADSET. Read More »
-
TSB #MTI_1111
When installing a navigation SD card, confirm that the card is unlocked. Also, Mazda Does Not Recommend swapping navigation system SD cards from one vehicle to another for testing. Read More »
-
TSB #SA278
After Pandora V7.0 was released on March 7th, the following problems have been found on vehicle with MAZDA CONNECT. Navigation voice guidance will skip and cut out losing many words. Read More »
-
TSB #0900916
HandsFree bluetooth module and/or text messaging troubleshooting procedure Read More »
-
TSB #0100116
Engine Start /Stop Procedure with room fuse removed Read More »
-
TSB #MULTI-MODELS 13
BLIND SPOT MONITORING (BSM) SYSTEM CHANGE. THE 2016 MX-5, 2016 CX-3 AND NEW 2016 CX-9 BSM SYSTEM VEHJICLE DETECTION HAS CHANGED. ALTHOUGH THE OVERALL FUNCTION IS THE SAME AS PREVIOUS VEJHICLES, VEHICLE DETECTION IS DIFFERENT. Read More »
-
TSB #15-001/16
LDWS OR ALH WARNING LIGHT ON WITH DTC C1001:92. SOME VEHICLES MAY EXPERIENCE ONE OF THE FOLLOWING 2 SYMPTOMS, EVEN THOUGH THE WINDSHIELD IS CLEAR. Read More »
-
TSB #09-036/15
BSM RADAR AIMING CANNOT BE PERFORMED AFTER RIGHT-SIDE BSM CONTROL MODULE REPLACEMENT. IF RIGHT-DIDE BSM CONTROL MODULE REQURES REPLACEMENT FOR ANY REPAIR, ALSO REPLACE LEFT SIDE BSM CONTROL MODULE TO COMPELTE THE RADAR AIMING PROCEDURE ... Read More »
-
TSB #0101415
Engine Oil seepage from engine oil pressure switch Read More »
-
TSB #09-044/15
MAZDA CONNECT SHUTS DOWN AND DOES NOT REBOOT. SOME VEHICLES MAY EXPERIENCE MAZDA CONNECT INFOTAINMENT SYSTEM SHUTTING DOWN WITH A FEW MINUTES AFTER IGNITION IS TURNED ON, AND WILL NOT REBOOT. Read More »
-
TSB #0904415
Mazda connect shuts down and does not reboot Read More »
-
TSB #15-001-15-3092
SOME VEHICLES MAY EXPERIENCE ONE OF THE FOLLOWING 2 SYMPTOMS, EVEN THOUGH THE WINDSHIELD IS CLEAR: 1.LANE DEPARTURE WARNING SYSTEM (LDWS) WARNING LIGHT TURNS ON AT IDLE. Read More »
-
TSB #08-002-23
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. DTC B00A0:09 (Occupant classification sensor internal signal output unstable). Read More »
-
TSB #01-006-21-3779a
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #08-001-20-3696
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. DTC B00A0:09 (Occupant classification sensor internal signal output unstable). Read More »
-
TSB #MT-004-18
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #MT-008-18
Some customers may complain about: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator, light flashing, Battery discharge, Electrical relay buzzing noise. Read More »
-
TSB #01-008-18-3451
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. Read More »
-
TSB #01-009-18-3452
The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #1096M
IF THE ACTIVE DRIVING DISPLAY (AD-DISP) UNIT REQUIRES REMOVAL, USE CAUTION WHEN DISCONNECTING/CONNECTING THE WIRING HARNESS. IF THE HARNESS IS NOT CONNECTED PROPERLY, THE AD-DISP MAY NOT OPERATE. Read More »
-
TSB #SA-050-23
Some customers may complain about scratches on the instrument cluster lens. Read More »
-
TSB #07-002-23
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
-
TSB #SA-039-22
Some customers may complain about scratches on the instrument cluster lens. Read More »
-
TSB #09-009-19-3566
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #09-002-18-3410
After the installation of a new instrument cluster, the message "Fctry" or "Factory" is displayed instead ofthe odometer. This concern may also occur when a room fuse is installed in a new vehicle. Read More »
-
TSB #09-035-17-3080
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #SA-061-17
In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is? 2017 Mazda North American Operations, U.S.A. Read More »
-
TSB #09-019-17
Fctry MESSASGE DISPLAYED after instrument cluster replacement. After the installation of a new instrument cluster, the message "Fctry" is displayed instead of the odometer. Some new instrument clusters are in the factory mode setting. Read More »
-
TSB #09018173351
Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature. Read More »
-
TSB #09-018-17
Display shows inaccurate ambient temperature. Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature. Read More »
-
TSB #MT-010-17
Some customers may claim that it is impossible or difficult to view the Active Driving Display, even if the position of the display is adjusted through the Settings screen. Read More »
-
TSB #09-016-23
Speedometer replacement procedure Read More »
-
TSB #09-024-22
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. Read More »
-
TSB #SA-001-22b
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-001/22
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
-
TSB #09-021-21-3818b
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #09-030-20-3740
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #09-022-19-3599a
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #SA-047-18
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #SA-017-18
Upgrade your PCs to IDS version 109.00 and 109.01 from the previous version. NOTE: You may see ?Selection not available? on IDS when a selecting ?Programming menu?, 108. Read More »
-
TSB #SA-016-18
If the MAZDA CONNECT Connectivity Master Unit (CMU) is replaced due to failure, the replacement CMU may have a navigation system software error. To resolve this concern, after the installation of the new CMU, check the software version. Read More »
-
TSB #09-010-18-3440
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.504 or later). NOTE: For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #09-001-18-3387a
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during extremely cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. Read More »
-
TSB #09-007-18-3422
Some customers may experience a navigation system screen that shows the wrong location. This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified. Read More »
-
TSB #SA-036-17
IDS SOFTWARE VERSION 107 AVAILABLE ON MGSS - PLEASE UPDATE YOUR PC'S. Upgrade your PCs to IDS version 107.00 and 107.01 from the previous version. Read More »
-
TSB #15-001-17-3301a
Some vehicles with Blind Spot Monitoring (BSM) may experience the following conditions (similar to when the BSM control modules detect dirt on the rear bumper surface): DTC U1A4B:97 - Radar sensor sensitivity temporarily decreases ... Read More »
-
TSB #SA-063-17
Some customers may complain about the "wrong" phone is connected to the infotainment system. MAZDA CONNECT bluetooth will connect all profiles to devices in order of priority if the last device is not available. Read More »
-
TSB #09-017-17-3347b
All Mazda Connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #SA-048-17
In order to do a CMU data retrieval for the new MAZDA CONNECT software, make sure to use version 31 (available on MGSS). Read More »
-
TSB #09-017-17-3347a
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502or later).NOTE:For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #SA-046-17
An update to the MAZDA CONNECT system is now available for download from the Mazda Global Service Support (MGSS) system. The new version number is 59.00.502. Please refer to TSB 09-017/17 for a list of improvements to the system. Read More »
-
TSB #09017173346
All Mazda Connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #SA234
IDS UPDATE 101.00 AND 101.02 IS NOW AVAILABLE ON MS3 UNDER THE "IDS/INFOTAINMENT" TAB. Read More »
-
TSB #09-024-16-3192B
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 55.00.760 OR LATER).?SOME STREET NAMES IN CANADA ARE NOT DISPLAYED. Read More »
-
TSB #09-024-16-3192A
ALL MAZDA CONNECT VEHICLES IN NEW CAR INVENTORY MUST BE UPDATED TO THIS SOFTWARE VERSION LISTED BELOW IN THIS TSB AS PART OF THE NEW CAR READY STEP 3 PROCESS. MAKE SURE THE NEW VEHICLE SPECIALIST RECEIVES A COPY OF THIS BULLETIN. Read More »
-
TSB #09-024-16-3192
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 56.00.760 OR LATER).?SOME STREET NAMES IN CANADA ARE NOT DISPLAYED. Read More »
-
TSB #SA51
MAZDA CONNECT SOFTWARE VERSION 55.00.760 IS NOW AVAILABLE ON MS3. USE THIS VERSION FOR ALL MAZDA CONNECT UPDATES, INCLUDING OPEN SSP98 VEHICLES. IF SSP98 IS CLOSED, USE TSB 09-024/16 TO REPAIR THE VEHICLES. Read More »
-
TSB #09-044-15-3094
SOME VEHICLES MAY EXPERIENCE THE MAZDA CONNECT INFOTAINMENT SYSTEM SHUTTING DOWN WITHIN A FEW MINUTES AFTER THE IGNITION IS TURNED ON, AND WILL NOT REBOOT. IT WILL ONLY REBOOT AFTER THE IGNITION IS TURNED OFF AND THEN ON AGAIN. Read More »
-
TSB #MAZDA 15-001
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #09-022-15-3047C
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 55.00.753 OR LATER). Read More »
-
TSB #00-002-20-3749
In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on an ??A?A?as-needed??A?A? basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. Read More »
-
TSB #MTI_1115
Multi-Model - Blind Spot Monitoring (BSM) System Change (update) Read More »
-
TSB #0901316
Excessive condensation or water within the headlamp assembly caustion Read More »
-
TSB #MTI_1031
Some customers may complain about a blurry rear view monitor display. This may be caused by an aftermarket accessory device. Read More »
-
TSB #SA-010-23
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #SA-036-21
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
-
TSB #09-010-19-3624
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #09-003-19-3555a
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #09-003-19-3555
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #15-005-17-3358b
Some customers may complain that the BSM indicator light on the outer mirror glass does not illuminate when: ? Customer vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area. Read More »
-
TSB #15-003-17-3284a
Some customers may notice that the Lane Departure Warning System (LDWS) and High Beam Control (HBC) (amber) warning lights are on when they start driving around dusk or dawn under low temperatures. Read More »
-
TSB #1066M
SOME CUSTOMERS MAY COMPLAIN ABOUT IMPROPER OPERATION OF THE AUTO-DIMMING MIRROR. THIS MAY BE CAUSED BY AN OBSTRUCTION OF THE FRONT AND/OR REAR LIGHT SENSOR(S) (E.G. HANGING A PARKING PERMIT FROM THE MIRROR). Read More »
-
TSB #0800116
Passenger fAirbag deactivation (PAD) indicator light illumination Read More »
-
TSB #09-003-19-3555a
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #09-041-18-3533
Some customers may notice water entry into the front combination lights. This is due to poor sealing where rain or other water can enter inside the light. Read More »
-
TSB #09-011-18-3448
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #09-001-17-3296b
When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. Read More »
-
TSB #SA-057-17
High Beam Control (HBC) system frequently asked questions (FAQ) Read More »
-
TSB #09-008-17-3324
Take caution when cleaning plastic headlight lenses. Damage can occur when using some cleaners that contain strong acid, alkaline cleanser or organic solvent. Read More »
-
TSB #09-003-16-3130
SOME CUSTOMERS MAY COMPLAIN OF CONDENSATION/FOG INSIDE THE FRONT (HEADLAMP/HEADLIGHT) OR REAR (TAILLAMP/TAIL-LIGHT) COMBINATION LIGHTS. Read More »
-
TSB #15-001-16-3126
SOME VEHICLES MAY EXPERIENCE ONE OF THE FOLLOWING 2 SYMPTOMS, EVEN THOUGH THE WINDSHIELD IS CLEAR: 1. LANE DEPARTURE WARNING SYSTEM (LDWS) WARNING LIGHT TURNS ON AT IDLE. Read More »
-
TSB #SB-15-001-15
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #SA-023-18
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
-
TSB #SA-066-17
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
-
TSB #15-003-17-3284a
Some customers may notice that the Lane Departure Warning System (LDWS) and High Beam Control (HBC) (amber) warning lights are on when they start driving around dusk or dawn under low temperatures. Read More »
-
TSB #SA390
Excessive water intrusion or condensation of Halogen headlight Read More »
-
TSB #15003173284
? After installing the new Forward Sensing Camera (FSC), frequency of the disabled function with the LDWS/HBC warning lights ON due to foggy FSC lens will be reduced. Read More »
-
TSB #0900316
Condensation/Fog in front and rear combination lights Read More »
-
TSB #09-003-19-3555a
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #09-011-18-3448
Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. Read More »
-
TSB #09-003-16-3130
SOME CUSTOMERS MAY COMPLAIN OF CONDENSATION/FOG INSIDE THE FRONT (HEADLAMP/HEADLIGHT) OR REAR (TAILLAMP/TAIL-LIGHT) COMBINATION LIGHTS. Read More »
-
TSB #15-003-17-3284b
Some customers may notice that the Lane Departure Warning System (LDWS) and High Beam Control (HBC) (amber) warning lights are on when they start driving around dusk or dawn under low temperatures. Read More »
-
TSB #09-031-20b
Some vehicles may exhibit a distorted image or no image from the rear mount camera when shifted into reverse. Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. Read More »
-
TSB #09-031/20a
Be advised that TSB "09-031/20 - REAR MOUNT CAMERA IMAGE NOT CLEAR/NO IMAGE ON SCREEN" is no longer valid and has been superseded by "RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY". Read More »
-
TSB #00-001-23
In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on an ??A?A?as-needed??A?A? basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. Read More »
-
TSB #09-025-23
Some customers may complain that the frequency of replenishing the window washer liquid is higher than expected, or they may complain of leakage at or around the washer motor (1). Read More »
-
TSB #SA-012-23
Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet. Read More »
-
TSB #SA-010-23
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #09-014-21-3802a
Some vehicles may exhibit a crack in the lower center area of the windshield. This may be caused by fixtures located at the center of the cowl grille, which result in higher pressures applied to the windshield. Read More »
-
TSB #09-022-21-3815
Some customers may complain that the frequency of replenishing the window washer liquid is higher than expected, or they may complain of leakage at around the washer motor (1). Read More »
-
TSB #09-014-21-3802
Some vehicles may exhibit a crack in the lower center area of the windshield. This may be caused by fixtures located at the center of the cowl grille, which result in higher pressures applied to the windshield. Read More »
-
TSB #SA-015-21
Some customers may complain that the Blind Spot Monitoring (BSM) system is inoperative. The symptoms may include: When the ignition is switched ON, the warning indicator light turns ON momentarily and then turns off after a few seconds. Read More »
-
TSB #00-002-20-3749
In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on an ??A?A?as-needed??A?A? basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. Read More »
-
TSB #09-031-20-3736
Some vehicles may exhibit a distorted image or no image from the rear mount camera when shifted into reverse. Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. Read More »
-
TSB #SA-027-19
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
-
TSB #09-010-19-3624
Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. Read More »
-
TSB #15-005-17-3358c
Some customers may complain that the BSM indicator light on the outer mirror glass does not illuminate when: Customer vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area. Read More »
-
TSB #09-044-17-3398
Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Read More »
-
TSB #15-005-17-3358a
Some customers may complain that when passing a vehicle slowly, even if the vehicle is still in the alert area, the BSM indicator light on the outer mirror glass does not illuminate. Read More »
-
TSB #15-005-17-3358
Some customers may complain that when passing a vehicle slowly, even if the vehicle is still in the alert area, the BSM indicator light on the outer mirror glass does not illuminate. Read More »
-
TSB #07-006-17
A/C blows warm air due to regrigerant leak Read More »
-
TSB #09-007-17
Front door window glass rattle noise Read More »
-
TSB #MT-001-17
Windshield washer fluid change - Factory filled windshield washer fluid has been changed to an ethanol type (yellow color) instead of athe conventional methanol type (blue color). Read More »
-
TSB #15-001-16-3126
Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). Read More »
-
TSB #09-014-21-3802a
Some vehicles may exhibit a crack in the lower center area of the windshield. This may be caused by fixtures located at the center of the cowl grille, which result in higher pressures applied to the windshield. Read More »
-
TSB #SA-058-17
CAUTION: DO NOT attempt any repair of the windshield damaged by stone chipping/cracks at the area in front of the Forward Sensing Camera (FSC) and Laser Sensor. Replace the windshield with a new one instead. Read More »
-
TSB #15-001-16-3126
SOME VEHICLES MAY EXPERIENCE ONE OF THE FOLLOWING 2 SYMPTOMS, EVEN THOUGH THE WINDSHIELD IS CLEAR. UNDER CERTAIN DRIVING CONDITIONS, THE FORWARD SENSING CAMERA (FSC) MAY DETECT A DIRTY WINDSHIELD (NOT CLEAR). Read More »
-
TSB #15-001-16-3126
SOME VEHICLES MAY EXPERIENCE ONE OF THE FOLLOWING 2 SYMPTOMS, EVEN THOUGH THE WINDSHIELD IS CLEAR: 1. LANE DEPARTURE WARNING SYSTEM (LDWS) WARNING LIGHT TURNS ON AT IDLE. Read More »
-
TSB #SA-039-23a
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #SA-040-21
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #MT-003-21
Some vehicles may experience exterior trim heat damage when parked near a glass building. This may be caused by the suns reflection. Read More »
-
TSB #MT-007-18
ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. Read More »
-
TSB #MT-001-17
Windshield washer fluid change - Factory filled windshield washer fluid has been changed to an ethanol type (yellow color) instead of athe conventional methanol type (blue color). Read More »
-
TSB #SA-012-23
Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet. Read More »
-
TSB #SA-074-22
Some customers may complain the HVAC system not maintaining the correct temperature or the ambient (outside) temperature reading incorrectly. This is caused by a failure in the ambient temperature sensor. Read More »
-
TSB #07-006-17
A/C blows warm air due to regrigerant leak Read More »
-
TSB #07-001-17
a/c blows warm air Read More »
-
TSB #MTI_1034
THIS ARTICLE PROVIDES HVAC HEATER/DEFROSTER OPERATING TIPS USING MODE SELECTOR DIAL. THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS. Read More »
-
TSB #07-005-21-3836
Some customers may complain about warm air from the climate control vents. This may be caused by improper brazing (A) of the evaporator (B), causing a refrigerant leak from the joint between the tubes (C) and the header (D). Read More »
-
TSB #MTI_1034
THIS ARTICLE PROVIDES HVAC HEATER/DEFROSTER OPERATING TIPS USING MODE SELECTOR DIAL. THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS. Read More »
-
TSB #08-002-23
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. DTC B00A0:09 (Occupant classification sensor internal signal output unstable). Read More »
-
TSB #08-003-22
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. Read More »
-
TSB #SA-042-21
Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc. Read More »
-
TSB #08-001-20-3696a
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. ??A?A? DTC B00A0:09 (Occupant classification sensor internal signal output unstable). Read More »
-
TSB #08-001-19-3544
This information is provided to help address Passenger Airbag Deactivation (PAD) Indicator illumination concerns during vehicle service. Read More »
-
TSB #08-001-18-3457
This information is provided to help address Passenger Airbag Deactivation (PAD) Indicator illumination concerns during vehicle service. Read More »
-
TSB #MT-003-18
The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles. Read More »
-
TSB #01-001-17
Some vehicles may experience the CHECK ENGINE LIGHT OIN with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A removed * P2610 Instrument cluster internal engine off timer performance problem * P2507 PCM battery ... Read More »
-
TSB #02-001-17
TPMS WARNING LIGHT ON - Some vehicles may experience a Tire Pressure Monitoring System (TPMS) warning light on when driving on a smooth road surface even if the TPMSF system has been properly initialized at the specified tire air pressure. Read More »
-
TSB #SA327
TAKATA recalls for Air bag Read More »
-
TSB #0800116
Passenger fAirbag deactivation (PAD) indicator light illumination Read More »
-
TSB #08-001-20-3696
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. DTC B00A0:09 (Occupant classification sensor internal signal output unstable). Read More »
-
TSB #SA-027-18
Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc. Read More »
-
TSB #08-002-23
Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. DTC B00A0:09 (Occupant classification sensor internal signal output unstable). Read More »
-
TSB #SA-027-18
Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc. Read More »
-
TSB #SA-039-23a
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #SA-039-23
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #SA-036-23
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the ... Read More »
-
TSB #SA-008-22a
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #09-017-22a
Some vehicles may have rust on the contact parts between the clips (for attaching the roof molding) and the roof panel (ditches of the roof rail). Read More »
-
TSB #SA-008-22
Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. Read More »
-
TSB #MT-001-22
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Read More »
-
TSB #09-036-21-3848
Some vehicles may exhibit rust (1) on the liftgate around the border of the rear mount camera (2) and/or the liftgate opener switch (3). Repair the rust and install a pad to prevent future rust. Read More »
-
TSB #SA-009-20
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. Read More »
-
TSB #09-041-18-3533
Some customers may notice water entry into the front combination lights. This is due to poor sealing where rain or other water can enter inside the light. Read More »
-
TSB #09-014-18-3443a
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #09-021-18-3459a
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #09-014-18-3443
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #09-045-17-3393
Some customers driving on snow and ice may find the front step molding falling off. This may be caused by snow and ice accumulated under the molding when contacting a snow pile. Read More »
-
TSB #15-005-17-3358c
Some customers may complain that the BSM indicator light on the outer mirror glass does not illuminate when: Customer vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area. Read More »
-
TSB #09-001-17-3296b
When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. Read More »
-
TSB #09-049-16
Rattle noise from rear spoiler when closing liftgate Read More »
-
TSB #1095M
SOME CUSTOMERS MAY COMPLAIN ABOUT A BUZZ/RATTLE TYPE NOISE AT 2400 RPM. THE NOISE CAN BE HEARD AT A STOP OR WHILE DRIVING. THIS MAY BE CAUSED BY AN EVAP HOSE MAKING CONTACT WITH THE VEHICLE UNDERBODY. Read More »
-
TSB #1098M
WHEN REMOVING PARTS FROM A VEHICLE, TAKE CAUTION OF THIS SYMBOL "R". FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE. Read More »
-
TSB #1095M
SOME CUSTOMERS MAY COMPLAIN ABOUT A BUZZ/RATTLE TYPE NOISE AT 2400 RPM. THE NOISE CAN BE HEARD AT A STOP OR WHILE DRIVING. THIS MAY BE CAUSED BY AN EVAP HOSE MAKING CONTACT WITH THE VEHICLE UNDERBODY. Read More »
-
TSB #1098M
WHEN REMOVING PARTS FROM A VEHICLE, TAKE CAUTION OF THIS SYMBOL "R". FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE. Read More »
-
TSB #09-036-16-3198
SOME VEHICLES MAY EXHIBIT A VISIBLE WHITE FELT THROUGH THE GAP BETWEEN THE FRONT DOOR TRIM AND THE DOOR ARM REST, CAUSING POOR APPEARANCE. THIS IS DUE TO A DECREASE OF ADHESIVE FORCE UNDER HIGH AMBIENT TEMPERATURES. Read More »
-
TSB #09-036-16-3198
SOME VEHICLES MAY EXHIBIT A VISIBLE WHITE FELT THROUGH THE GAP BETWEEN THE FRONT DOOR TRIM AND THE DOOR ARM REST, CAUSING POOR APPEARANCE. THIS IS DUE TO A DECREASE OF ADHESIVE FORCE UNDER HIGH AMBIENT TEMPERATURES. Read More »
-
TSB #09-028-16-3189
SOME VEHICLES MAY EXHIBIT A RATTLE/CHATTER TYPE NOISE FROM THE A/C VENTS WHEN DRIVING ON AN UNEVEN/ROUGH ROAD SURFACE . Read More »
-
TSB #Mazda TSB March
Mazda Technical Service Bulletins March 2016 Some vehicles may exhibit the inner cloth (A) falling down at the rear end causing a poor appearance and obstructing the view of the back window. Read More »
-
TSB #02-005-16-3152a
Beginning with the CX-5 and Mazda6 models, grip type front and rear stabilizer bushings have been incorpo-rated for noise prevention purposes. Read More »
-
TSB #09-010/16
STAINS FOUND ON PAINT DURING PDI SOME VEHICLES MAY EXPERIENCE STAINS APPEARING ON THE HOOD, ROOF AND/OR TRUNK OF VEHICLE. THIS CONCERN IS MOST LIKELY TO BE FOUND IN COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. Read More »
-
TSB #02-010-16-3170
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
-
TSB #MT-012-18
If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. Read More »
-
TSB #09-047-17-3396
On some vehicles, one or more roof carrier brackets (A) may be installed in reverse (with arrows (B) facing outward). In this case, accessories, such as a roof carrier cannot be installed. Read More »
-
TSB #0901016
Stains found on kpaint during PDI Read More »
-
TSB #09-033-15-3069
SOME VEHICLES MAY EXHIBIT THE REAR DOOR SIDE GARNISH DETACHING FROM THE DOOR (1 OR BOTH SIDES). Read More »
-
TSB #09-004-20-3666
Some vehicles may exhibit rust (A) on the liftgate around the border of the rear mount camera (B) and/or the liftgate opener switch (C). Repair the paint rust and install a pad to prevent future paint rust. Read More »
-
TSB #SA-050-17
CAUTION: At no point during the repair for Recall 9916H (LIFTGATE STAY DAMPER SAFETY RECALL) should "Vise-Grips" or other similar tools be used to hold the lift gate stay dampers. Use only the tools specified in the recall. Read More »
-
TSB #09-049-16-3233
SOME VEHICLES MAY EXHIBIT A RATTLE NOISE FROM THE REAR SPOILER WHEN CLOSING THE LIFTGATE.THIS MAY BE CAUSED BY TOO MUCH CLEARANCE BETWEEN THE REAR SPOILER AND LIFTGATE GLASS. Read More »
-
TSB #SA-050-17
CAUTION: At no point during the repair for Recall 9916H (LIFTGATE STAY DAMPER SAFETY RECALL) should "Vise-Grips" or other similar tools be used to hold the lift gate stay dampers. Use only the tools specified in the recall. Read More »
-
TSB #09-021-18-3459
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #SA-040-19
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
-
TSB #SA-024-18
Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system. Read More »
-
TSB #09-021-18-3459
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #09-022-18-3471
On some vehicles, one or more roof carrier brackets (A) may be installed in reverse (with arrows (B) facing outward). In this case, accessories, such as a roof carrier cannot be installed. Read More »
-
TSB #09-021-18-3459
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #SA-050-22
Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. Read More »
-
TSB #09-004-20-3666
Some vehicles may exhibit rust (A) on the liftgate around the border of the rear mount camera (B) and/or the liftgate opener switch (C). Repair the paint rust and install a pad to prevent future paint rust. Read More »
-
TSB #09-002-21-3770
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer Read More »
-
TSB #09-034-18-3430a
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #09-034-18-3430
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #01-013-16-3202
SOME VEHICLES MAY EXHIBIT THE ACCELERATOR PEDAL HINGE SEPARATING FROM THE BASE IN COLD TEMPERATURES BELOW 32 DEGREES FAHRENHEIT (0 DEGREES CELSIUS).THE ACCELERATOR PEDAL HAS BEEN CHANGED TO INCREASE DURABILITY. Read More »
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #02-012-16-3181
SOME VEHICLES MAY EXPERIENCE A TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON WHEN DRIVING ON A SMOOTH ROAD SURFACE EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. Read More »
-
TSB #MT-002-20
New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010. Read More »
-
TSB #MT-010-18
Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. Read More »
-
TSB #02-011-18-3476
This service bulletin illustrates the conditions when a TPMS warning light may illuminate, why it illuminated and how to properly initialize the system. Read More »
-
TSB #02-009-18-3472
Customer complaints have been reported where the TPMS warning light is unnecessarily illuminated because the TPMS initialization was not performed correctly before customer delivery. Read More »
-
TSB #02-012-16-3181A
SOME VEHICLES MAY EXPERIENCE A TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON WHEN DRIVING ON A SMOOTH ROAD SURFACE EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. Read More »
-
TSB #02-012-16-3181
SOME VEHICLES MAY EXPERIENCE A TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON WHEN DRIVING ON A SMOOTH ROAD SURFACE EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. Read More »
-
TSB #SA280
SOME VEHICLES MAY EXPERIENCE A TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT IMPROPERLY ILLUMINATES WHEN DRIVING ON A SMOOTH ROAD SURFACE EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. Read More »
-
TSB #SA280
SOME VEHICLES MAY EXPERIENCE A TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT IMPROPERLY ILLUMINATES WHEN DRIVING ON A SMOOTH ROAD SURFACE EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. Read More »
-
TSB #SA-022-24
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #SA-011-24
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-031-23
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #SA-006-22a
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #02-002-21-3769a
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #00-001-21-3768
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #02-002-21-3769
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #MT-002-20
New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010. Read More »
-
TSB #02-004-20-3685
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #SA-016-19
There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #02-002-19-3546
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #06-002-18-3504
Some vehicles may exhibit a light resistance and/or an unusual noise when turning the steering wheel to the left. This concern may be caused by insufficient lubrication of the gear due to uneven and deteriorated grease. Read More »
-
TSB #02-008-18-3467
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint ... Read More »
-
TSB #SA280
Some vehicles may experience a Tire Pressure Monitoring System (TPMS) warning light improperly illuminates when driving on a smooth road surface even if the TPMS system has been properly initialized at the specified tire air pressure. Read More »
-
TSB #SA-027-19
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
-
TSB #09-029-19-3594
Some customers may notice that the driver's seat gradually moves downward by itself and needs to be re-adjusted after 3 or 4 days of driving. Read More »
-
TSB #MT-001-19
Some customers may complain about a tapping or knocking noise coming from the rear seat after fuel fill. Read More »
-
TSB #09-015-18-3445a
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Read More »
-
TSB #09-015-18-3445
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Read More »
-
TSB #09-065-16
Rear seat back (RH) difficult to ljock in its upright position. Some customers may complain that it is difficult to lock the rear seat back (RH) to the upright position. The right side seat back weight is lighter than the left side. Read More »
-
TSB #09-016-16-3158A
AT PDI OR WHEN NEW VEHICLE IS DELIVERED, SOME CUSTOMERS MAY COMPLAIN ABOUT WRINKLES ON THE LEATHER SEAT CUSHION AND/OR SEAT BACK SURFACE. Read More »
-
TSB #09-016-16-3158A
AT PDI OR WHEN NEW VEHICLE IS DELIVERED, SOME CUSTOMERS MAY COMPLAIN ABOUT WRINKLES ON THE LEATHER SEAT CUSHION AND/OR SEAT BACK SURFACE. Read More »
-
TSB #09-032-16-3201
SOME CUSTOMERS MAY COMPLAIN ABOUT A FRONT SEAT RECLINER LEVER KNOB DIFFICULT TO MOVE. THIS MAKES IT DIFFICULT TO CHANGE THE SEAT BACK RECLINING POSITION. Read More »
-
TSB #09-034-16-3199
SOME CUSTOMERS MAY FIND WHITE DUST UNDER FRONT SEATS AND/OR PARTIALLY COLLAPSED SIDE SUPPORT OF THE SEAT CUSH-ION. Read More »
-
TSB #09-016-16-3158
AT PDI OR WHEN NEW VEHICLE IS DELIVERED, SOME CUSTOMERS MAY COMPLAIN ABOUT WRINKLES ON THE LEATHER SEAT CUSHION AND/OR SEAT BACK SURFACE. Read More »
-
TSB #09-016-16-3158
AT PDI OR WHEN NEW VEHICLE IS DELIVERED, SOME CUSTOMERS MAY COMPLAIN ABOUT WRINKLES ON THE LEATHER SEAT CUSHION AND/OR SEAT BACK SURFACE. Read More »
-
TSB #09-016-16-3158
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Read More »
-
TSB #MULTI-MODEL 7
MANUAL DRIVERS SEAT MOVES DOWN BY ITSELF. SOME CUSTOMERS MAY COMPLAIN THAT THE MANUAL DRIVERS SEAT GRADUALLY MOVES DOWN AND NEEDS RE-ADJUSTMENT OF THE HEIGHT POSITION. Read More »
-
TSB #MULTI-MODEL 7
MANUAL DRIVERS SEAT MOVES DOWN BY ITSELF. SOME CUSTOMERS MAY COMPLAIN THAT THE MANUAL DRIVERS SEAT GRADUALLY MOVES DOWN AND NEEDS RE-ADJUSTMENT OF THE HEIGHT POSITION. Read More »
-
TSB #SA-036-21
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
-
TSB #SA-003-19
Some vehicles may have one of the following DTCs stored in memory: C1001:92 - Forward sensing camera (FSC) poor field of view. B14F0:92 - General temporary failure in forward sensing camera (FSC). Read More »
-
TSB #SA-056-17
Mazda Radar Criose Control (MRCC) system frequently asked questions (FAQ) Read More »
-
TSB #MT-016-17
The Smart City Brake Support (SCBS) system alerts the driver of a possible collision using an indication in the display and a warning sound when the Forward Sensing Camera (FSC) detects a vehicle ahead and determines that a collision with ... Read More »
-
TSB #SA-066-17
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
-
TSB #SA-037-20
Some vehicles may have one of the following DTCs stored in memory: ??A?A? C1001:92 - Forward sensing camera (FSC) poor field of view ??A?A? B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set ... Read More »
-
TSB #SA-003-19
Some vehicles may have one of the following DTCs stored in memory: C1001:92 - Forward sensing camera (FSC) poor field of view. B14F0:92 - General temporary failure in forward sensing camera (FSC). Read More »
-
TSB #SA-003-19
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
-
TSB #00-001-23
In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on an ??A?A?as-needed??A?A? basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. Read More »
-
TSB #SA-036-21
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
-
TSB #00-004-18-3515
In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on a "as-needed" basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. Read More »
-
TSB #15-003-17-3284a
Some customers may notice that the Lane Departure Warning System (LDWS) and High Beam Control (HBC) (amber) warning lights are on when they start driving around dusk or dawn under low temperatures. Read More »
-
TSB #SA-053-17
Lane Departure Warning System (LDWS) frequently asked questions (FAQ) Read More »
-
TSB #02-001-17
TPMS WARNING LIGHT ON - Some vehicles may experience a Tire Pressure Monitoring System (TPMS) warning light on when driving on a smooth road surface even if the TPMSF system has been properly initialized at the specified tire air pressure. Read More »
-
TSB #MTI_1115
Multi-Model - Blind Spot Monitoring (BSM) System Change (update) Read More »
-
TSB #SA-023-18
Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. Read More »
-
TSB #15-003-17-3284b
Some customers may notice that the Lane Departure Warning System (LDWS) and High Beam Control (HBC) (amber) warning lights are on when they start driving around dusk or dawn under low temperatures. Read More »
-
TSB #15-003-17-3284a
Some customers may notice that the Lane Departure Warning System (LDWS) and High Beam Control (HBC) (amber) warning lights are on when they start driving around dusk or dawn under low temperatures. Read More »
-
TSB #SB-15-001-15
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #00-003/22
In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on as-needed basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. Read More »
-
TSB #System
Blind spot monitoring (BSM) system change Read More »
-
TSB #09-017-19-3473
If the right-side Blind Spot Monitoring (BSM) control module is replaced for any reason, it is also necessary to replace the left-side BSM control module in order to complete the radar aiming procedure. Read More »
-
TSB #09-031-18-3489
If it becomes necessary to replace the right-side Blind Spot Monitoring (BSM) control module, the configuration may fail even though the Workshop Manual procedure was performed properly. Read More »
-
TSB #15-005-17-3358
Some customers may complain that when passing a vehicle slowly, even if the vehicle is still in the alert area, the BSM indicator light on the outer mirror glass does not illuminate. Read More »
-
TSB #SA-054-17
Blind Spot Monitoring (Advanced BSM) system frequently asked questions (FAQ) Read More »
-
TSB #15-001-17-3301
Some vehicles with Blind Spot Monitoring (BSM) may experience the following conditions (similar to when the BSM control modules detect dirt on the rear bumper surface): Read More »
-
TSB #15-002-17-3325
Some customers may complain of improper BSM performance under the following conditions. 1. Even if there is no vehicle in the alert area, the BSM indicator light on the outer mirror glass illuminates. 2. Read More »
-
TSB #MULTI-MODELS 13
BLIND SPOT MONITORING (BSM) SYSTEM CHANGE. THE 2016 MX-5, 2016 CX-3 AND NEW 2016 CX-9 BSM SYSTEM VEHJICLE DETECTION HAS CHANGED. ALTHOUGH THE OVERALL FUNCTION IS THE SAME AS PREVIOUS VEJHICLES, VEHICLE DETECTION IS DIFFERENT. Read More »
-
TSB #09-036-15-3081A
IF THE RIGHT-SIDE BSM CONTROL MODULE REQUIRES REPLACEMENT FOR ANY REPAIR, ALSO REPLACE THE LEFT SIDE BSM CONTROL MODULE TO COMPLETE THE RADAR AIMING PROCEDURE (IT IS OK TO REPLACE THE LEFT BSM ALONE). Read More »
-
TSB #09-032-23
SERVICE BULLETIN 09-031/20 ISSUED ON 09/21/20 IS NO LONGER VALID. IT IS SUPERCEDED BY RECALL 6023G (??A?A?2014-2018 MAZDA3 AND 2016-2021 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY??A?A?). Read More »
-
TSB #SA-001/22
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
-
TSB #SA-006-19a
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #02-003-17
Knocking/Squeaking noise from front shock absorber, creaking noise fkrom front lower arm bushing Read More »
-
TSB #09-002-17
Rust around rear view camera and/or liftgate opener switch Read More »
-
TSB #02-010-16
Knocking/squeaking noise from front shock absorber, creaking noise from front lower arm bushing. Read More »
-
TSB #09-031-20-3736
Some vehicles may exhibit a distorted image or no image from the rear mount camera when shifted into reverse. Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. Read More »
-
TSB #SA-001-22c
Use the symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-008-24
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-036-23
Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the ... Read More »
-
TSB #RF-22-01R3
This Parts Flash replaces RF-22-01R2 released January 04, 2022. It includes new display repair kit part numbers for the 2018-2019 Mazda2, 2018-2020 CX-3 and 2018-2020 MX-5. Repair kits are available to replace just the screen. Read More »
-
TSB #SA-001-23a
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: ... Read More »
-
TSB #09-003-23a
Some customers may complain about infotainment center display: - Center display touchscreen operates by itself (Ghost Touch). - The film of the center display may be peeled off. Read More »
-
TSB #RF-22-01R2
This Parts Flash replaces RF-22-01R released November 21, 2022. It includes a new display repair kit part number for the 2020-2022 MX-5. Repair kits are available to replace just the screen. Read More »
-
TSB #09-003-23
Some customers may complain about infotainment center display: - Center display touchscreen operates by itself (Ghost Touch). - The film of the center display may be peeled off. Read More »
-
TSB #SA-001-23
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: ... Read More »
-
TSB #SA-016-22a
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method Read More »
-
TSB #09-036-22
Some customers may complain about infotainment center display: - Center display touchscreen operates by itself (Ghost Touch). - The film of the center display may be peeled off. Read More »
-
TSB #09-023-22
Some customers may complain about spider web-like cracking (as shown below) appearing in the corner(s) of the MAZDA CONNECT center display. The cracks are internal and cannot be felt by touch. Read More »
-
TSB #SA-039-22
Some customers may complain about scratches on the instrument cluster lens. Read More »
-
TSB #09-017-22a
Some vehicles may have rust on the contact parts between the clips (for attaching the roof molding) and the roof panel (ditches of the roof rail). Read More »
-
TSB #SA-026-22
Apple CarPlay / Android Auto Frequently Asked Questions (FAQs) Read More »
-
TSB #SA-016-22
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method Read More »
-
TSB #00-003/22
In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on as-needed basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. Read More »
-
TSB #SA-001/22
Symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. No. 1 Blank Screen No. 2. Rear View Camera is not displayed No. 3 Rebooting No. 4 Infotainment System Has No Sound No. 5 Commander Switch Does Not Work No. Read More »
-
TSB #SA-019-21e
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns Read More »
-
TSB #SA-052-21
For improvement of electrical diagnosis, the SKYACTIV??A? Wiring Terminal Test Kits has been delivered all the dealers. Read More »
-
TSB #09-014-21-3802a
Some vehicles may exhibit a crack in the lower center area of the windshield. This may be caused by fixtures located at the center of the cowl grille, which result in higher pressures applied to the windshield. Read More »
-
TSB #07-005-21-3836
Some customers may complain about warm air from the climate control vents. This may be caused by improper brazing (A) of the evaporator (B), causing a refrigerant leak from the joint between the tubes (C) and the header (D). Read More »
-
TSB #SA-019-21d
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #MT-002-21
Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. Read More »
-
TSB #09-021-21-3818b
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #SA-019-21c
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #09-025-21-3824
This service bulletin provides information regarding the proper use of the driver??A?A?s floor mat to avoid any potential interference with the foot pedals. Read More »
-
TSB #09-021-21-3818
AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (6TH GENERATION). All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready ... Read More »
-
TSB #SA-030-21a
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method A. Read More »
-
TSB #SA-041-21
Accessory instructions can be found on OneMazda under Dealer Resources - Parts & Accessories. The links provided below can be used for quick access: For 2016 models and newer: NOTE: Instructions are found under the "Attachments" section ... Read More »
-
TSB #SA-029-21a
APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
-
TSB #09-017-21-3808
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black under any temperature. Read More »
-
TSB #SA-034-21
When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the DCA8000 OR GR8 battery charger SST to maintain battery voltage. Read More »
-
TSB #MT-002-21
When programming a key or installing a Genuine Mazda Accessory Remote Engine Start system, you may encounter programming difficulty. Read More »
-
TSB #MT-001-21
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #SA-030-21
Auxiliary key blank cutting procedure: There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method, B. Auxiliary Key Code Cut Method Read More »
-
TSB #SA-029-21
APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay??A?A? / Android Auto??A?A?, but it can be activated using MDARS. Read More »
-
TSB #SA-019-21a
MAZDA CONNECT Symptom Troubleshooting (6th Generation Vehicles). Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #Seat
Manual Driver's seat moves down by itself Some customer s may complain that the manual driver's seat gradually moves down and needs readjustment of the height position. Read More »
-
TSB #CSP05c
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
-
TSB #CSP05d
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no ... Read More »
-
TSB #01-003-21-3776
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. Read More »
-
TSB #07-001-21-3775
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #09-002-21-3770
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer Read More »
-
TSB #CSP05b
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #SA-004-20c
In order to ensure key code security, MNAO has restricted key code access for the new auxiliary key. This Service Alert provides information on how to obtain the 10-digit key code needed for cutting a new auxiliary key blank if all ... Read More »
-
TSB #06-004-20-3757
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
-
TSB #CSP05a
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #CSP05
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer ... Read More »
-
TSB #MT-004-20
Some customers may complain about a tapping or knocking noise coming from the rear seat after fuel fill. Read More »
-
TSB #SA-071-20
Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. Read More »
-
TSB #SA-070-20
APPLE CARPLAY / ANDROID AUTO FREQUENTLY ASKED QUESTIONS (FAQ): NOTE: The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. Read More »
-
TSB #SA-069-20
ACCESSORY INSTRUCTIONS LOCATION: Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.mazdausa.com Read More »
-
TSB #09-006-20-3673a
When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #MT-001-20
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #05-003-20-3725
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #SA-041-20
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #SA-026-20
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Audio System, Bluetooth??A?, Center Dislay, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux ... Read More »
-
TSB #09-006-20-3673
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #09-004-20-3666
Some vehicles may exhibit rust (A) on the liftgate around the border of the rear mount camera (B) and/or the liftgate opener switch (C). Repair the paint rust and install a pad to prevent future paint rust. Read More »
-
TSB #02-002-20-3651
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #09-003-20-3671
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #MT-002-19
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. Read More »
-
TSB #09-022-19-3599a
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #07-002-19-3616a
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #01-022-19-3657
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
-
TSB #SA-027-19
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
-
TSB #SA-049-19
Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint: ??A?A? MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE ??A?A? CANNOT COMMUNICATE WITH ... Read More »
-
TSB #MT-004-19
Some customers may complain about: ??A?A? Intermittent engine no start ??A?A? Instrument cluster red security indicator light ON ??A?A? Engine Start/Start Button Amber indicator light flashing ??A?A? Battery discharge ??A?A? Electrical ... Read More »
-
TSB #07-007-19-3638
Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a plugged heater core. Read More »
-
TSB #SSPB8a
The warranty coverage for the repair of the A/C Condenser due to refrigerant leak from condenser caused by corrosion is extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date, with no ... Read More »
-
TSB #07-001-19-3630
Some customers may complain about warm air from the climate control vents when the air conditioner is ON. This may be caused by condenser corrosion, causing a refrigerant leak. Read More »
-
TSB #07-003-19-3608
Some customers may complain about warm air from the climate control vents. This may be caused by improper brazing of the evaporator, causing a refrigerant leak from the joint between the tubes and the header. Read More »
-
TSB #SSPB8
The warranty coverage for the repair of the A/C Condenser due to refrigerant leak from condenser caused by corrosion is extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date, with no ... Read More »
-
TSB #09-031-19-3625
After the installation of a new instrument cluster, the message "Fctry" or ??A???A???A?Factory??A???A???A? is displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Read More »
-
TSB #SA-029-19a
The database error discovered with IDS 114.00-114.02 release has been fixed with IDS 114.04 release and is now available for download. Read More »
-
TSB #SA-031-19
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #07-002-19-3616
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #SA-029-19
Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. Read More »
-
TSB #SA-027-19
ACCESSORY INSTRUCTIONS LOCATION: Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/ Read More »
-
TSB #09-022-19-3599
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #01-008-19-3568a
Some customer using ??A???A???A?Flexible??A???A???A? setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. Read More »
-
TSB #SA-001-19b
APPLE CARPLAY??A?A? / ANDROID AUTO??A?A? FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #SA-013-19
MAZDA IDS INOPERATIVE WITH VCM-II LICENSE EXPIRATION MESSAGE - If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. Read More »
-
TSB #SA-001-19a
APPLE CARPLAY??A?A? / ANDROID AUTO??A?A? FREQUENTLY ASKED QUESTIONS (FAQ). Many frequently asked question and the answers. Read More »
-
TSB #00-003-19-3583
In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. Read More »
-
TSB #09-007-19-3564a
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH? hands-free unit or text messaging related concerns. Read More »
-
TSB #SA-001-19a
APPLE CARPLAY? / ANDROID AUTO? FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #00-001-19-3560
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #09-005-19-3562
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #09-007-19-3564
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH? hands-free unit or text messaging related concerns. Read More »
-
TSB #09-004-19-3543
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Read More »
-
TSB #SA-001-19
APPLE CARPLAY? / ANDROID AUTO? FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #09-001-19-3553
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as ... Read More »
-
TSB #SA-050-18
Some customers may complain that the navigation brand icons are no longer shown after a navigation SD card update. This is caused by a navigation map supplier software change. Customers can set preferences if needed. Read More »
-
TSB #SA-005-18
Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition. Read More »
-
TSB #09-010-18-3440b
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #MT-002-18
Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth? and the same device is also connected to the USB port for charging. Read More »
-
TSB #MT-011-18
SMS (Short Message Service) messages received by paired phones (Android and iPhone 5 iOS 7.0 or higher) can be downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. Read More »
-
TSB #00-001-18-3446a
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #00-003-18-3480a
Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. Read More »
-
TSB #09-014-18-3443a
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Read More »
-
TSB #09-020-18-3458b
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH? hands-free unit or text messaging related concerns. Read More »
-
TSB #09-021-18-3459a
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. Read More »
-
TSB #09-034-18-3430a
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #MT-004-18
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Read More »
-
TSB #MT-004-18
ELECTRICAL CONCERN AND/OR MULTIPLE DTC'S DUE TO AFTERMARKET DEVICE: If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored... Read More »
-
TSB #SA-034-18
MAZDA CONNECT SYSTEM FREQUENTLY ASKED QUESTIONS (FAQ) Read More »
-
TSB #SA-031-18
When troubleshooting a radar unit, DO NOT swap it with another vehicle. Radar units are configured to the original vehicle, and if installed in another vehicle, a configuration error will occur. Read More »
-
TSB #09-020-18-3458a
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH? hands-free unit or text messaging related concerns. Read More »
-
TSB #09-025-18-3479
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Read More »
-
TSB #09-023-18-3475
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as ... Read More »
-
TSB #01-011-18-3456
The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazdamodels, there is no key cylinder on the steering column. Read More »
-
TSB #MT-004-18
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
-
TSB #00-001-18-3446
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-008-18
Some customers may complain about the MAZDA CONNECT center display cracking (spider cracking). The cracks are internal and cannot be felt by touch. This may be caused by a faulty center display. Read More »
-
TSB #MT-003-18
The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles. Read More »
-
TSB #09-045-17-3393
Some customers driving on snow and ice may find the front step molding falling off. This may be caused by snow and ice accumulated under the molding when contacting a snow pile. Read More »
-
TSB #09-044-17-3398
Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Read More »
-
TSB #MT-019-17
WARNING: DO NOT PERFORM OPERATIONAL TESTING OF THE SMART CITY BRAKE SUPPORT (SCBS) SYSTEM. If the warning indicator light is not illuminated and there are no codes stored in the system, the system is operating properly, and Mazda cannot ... Read More »
-
TSB #MT-017-17
If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Read More »
-
TSB #MT-010-17
Some customers may claim that it is impossible or difficult to view the Active Driving Display, even if the position of the display is adjusted through the Settings screen. Read More »
-
TSB #MTI_1115
Multi-Model - Blind Spot Monitoring (BSM) System Change (update) Read More »
-
TSB #09-065-16
Rear seat back (RH) difficult to ljock in its upright position. Some customers may complain that it is difficult to lock the rear seat back (RH) to the upright position. The right side seat back weight is lighter than the left side. Read More »
-
TSB #SA266
MAZDA Mobile start (MMS) cannot communicate with vehicle Read More »
-
TSB #07-004-16
Auto A/C blows warm air (Canada/Mexico). Some customers may complain that it is difficult to adjuust the cabin temperature using the auto A/C. Read More »
-
TSB #07-006-16
A/C blows warm air. Some customers may complain about warm air from the climate cointrol vents. This may be caused by improper brazing (A) of the evaporator (B) causing a refrigerant leak fr om the joint between the tubes ? and the header ... Read More »
-
TSB #09-062-16
Active driving display opens/closes improperly. Some vehicles may exhibit the active driving display opening/closing improperly as described below: * It does not open or close when the ignition is turned ON or OFF . Read More »
-
TSB #09-061-16
Fctry MESSAGE DISPLAYED AFTER INSTRUMENT CLUSTER REPLACEMENT. After the installatioin of a new instrument cluster, the message "F ctry" IS DISPLAYED INSTEAD OF THE ODOMETER. Some new instrument clusters are in the factory mode setting. Read More »
-
TSB #00-005-16-3245
IN SUPPORT OF THE NEW MAZDA MX-5 AND CX-3, MAZDA WILL MAKE AVAILABLE FOR LOAN ON A ?AS-NEEDED? BASIS, A SPE-CIAL SERVICE TOOL (SST) TO ALLOW FOR THE RADAR AIMING OF THE BLIND SPOT MONITORING (BSM) SYSTEM. Read More »
-
TSB #00-004-16-3237
RAISING A VEHICLE WITH A JACK CAN BE DANGEROUS IF NOT DONE PROPERLY. THE VEHICLE CAN SLIP OFF THE JACK AND SERI-OUSLY INJURE SOMEONE. IN THIS SERVICE INFORMATION, SOME IMPORTANT WARNINGS AND CAUTIONS HAVE BEEN TAKEN FROM THE OWNER?S MANUAL. Read More »
-
TSB #MTI_1111
WHEN INSTALLING A NAVIGATION SD CARD, CONFIRM THAT THE CARD IS UNLOCKED. ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. Read More »
-
TSB #09-009-16-3150A
SOME VEHICLES MAY EXHIBIT BLUETOOTH? HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THE HANDLING OF BLUETOOTH? HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM ... Read More »
-
TSB #15-001-16-3126
SOME VEHICLES MAY EXPERIENCE ONE OF THE FOLLOWING 2 SYMPTOMS, EVEN THOUGH THE WINDSHIELD IS CLEAR. UNDER CERTAIN DRIVING CONDITIONS, THE FORWARD SENSING CAMERA (FSC) MAY DETECT A DIRTY WINDSHIELD (NOT CLEAR). Read More »
-
TSB #15-001-16-3126
Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). Read More »
-
TSB #MTI_1111
WHEN INSTALLING A NAVIGATION SD CARD, CONFIRM THAT THE CARD IS UNLOCKED. ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. Read More »
-
TSB #SA280
Some vehicles may experience a Tire Pressure Monitoring System (TPMS) warning light improperly illuminates when driving on a smooth road surface even if the TPMS system has been properly initialized at the specified tire air pressure. Read More »
-
TSB #MTI_1034
This article provides HVAC heater/defroster operating tips using Mode selector dial. This includes the use of intermediate positions. Read More »
-
TSB #MTI_1111
When installing a navigation SD card, confirm that the card is unlocked. Also, Mazda Does Not Recommend swapping navigation system SD cards from one vehicle to another for testing. Read More »
-
TSB #09-020-16-3183
SOME VEHICLES MAY EXPERIENCE A FUZZY APPEARANCE (TINY CRACKS) AROUND THE EDGE OF THE ACTIVE DRIVING DISPLAY. REPLACE THE ACTIVE DRIVING DISPLAY. Read More »
-
TSB #09-020-16-3183
Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Replace the Active Driving Display. Read More »
-
TSB #MTI_1031
SOME CUSTOMERS MAY COMPLAIN ABOUT A BLURRY REAR VIEW MONITOR DISPLAY. THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE. Read More »
-
TSB #MTI_1032
SOME CUSTOMERS MAY COMPLAIN ABOUT A RATTLE TYPE NOISE COMING FROM THE REAR OF THE VEHICLE WHEN DRIVING ON ROUGH ROADS. THIS MAY BE CAUSED BY A LOOSE SPARE TIRE JACK. Read More »
-
TSB #MTI_1031
SOME CUSTOMERS MAY COMPLAIN ABOUT A BLURRY REAR VIEW MONITOR DISPLAY. THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE Read More »
-
TSB #MTI_1032
Some customers may complain about a rattle type noise coming from the rear of the vehicle when driving on rough roads. This may be caused by a loose spare tire jack. Read More »
-
TSB #SA278
AFTER PANDORA V7.0 WAS RELEASED ON MARCH 7TH, THE FOLLOWING PROBLEMS HAVE BEEN FOUND ON VEHICLE WITH MAZDA CONNECT.NAVIGATION VOICE GUIDANCE WILL SKIP AND CUT OUT LOSING MANY WORDS. Read More »
-
TSB #SA278
AFTER PANDORA V7.0 WAS RELEASED ON MARCH 7TH, THE FOLLOWING PROBLEMS HAVE BEEN FOUND ON VEHICLE WITH MAZDA CONNECT.NAVIGATION VOICE GUIDANCE WILL SKIP AND CUT OUT LOSING MANY WORDS. Read More »
-
TSB #SA278
After Pandora V7.0 was released on March 7th, the following problems have been found on vehicle with MAZDA CONNECT. Navigation voice guidance will skip and cut out losing many words. Read More »
-
TSB #09-002/16
SUMMARY TO BE PROVIDED ON A FUTURE DATE. Read More »
-
TSB #09-002-16-3117
SOME VEHICLES MAY EXHIBIT EITHER ONE OR BOTH OF THE FOLLOWING POOR APPEARANCES AT THE COWL GRILLE. 1. THE BOTTOM OF THE WINDOW SHIELD IS VISIBLE WHEN THE COWL GRILLE IS PUSHED. 2. THE SIDE COVER OF THE COWL GRILLE IS DEFORMED. Read More »
-
TSB #0900216
COWL GRILLE POOR APPEARANCE Read More »
-
TSB #09-044/15
MAZDA CONNECT SHUTS DOWN AND DOES NOT REBOOT. SOME VEHICLES MAY EXPERIENCE MAZDA CONNECT INFOTAINMENT SYSTEM SHUTTING DOWN WITH A FEW MINUTES AFTER IGNITION IS TURNED ON, AND WILL NOT REBOOT. Read More »
-
TSB #09-040-15-3100
SOME VEHICLES MAY EXHIBIT SAIL GARNISH SEPARATION (ONE SIDE OR BOTH SIDES). THIS MAY BE CAUSED BY INSUFFICIENT ADHESION CAUSING ENLARGED CLEARANCE BETWEEN THE SAIL GARNISH AND THE FRONT SASH MOLDING. Read More »
-
TSB #SA-016-23
There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method Read More »
-
TSB #SA-026-20a
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-031-19
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #09-020-18-3458b
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH? hands-free unit or text messaging related concerns. Read More »
-
TSB #MT-008-18
ENGINE NO START (KEY NOT DETECTED): Some customers may complain about the following: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing. Read More »
-
TSB #09-020-18-3458
Some vehicles may exhibit BLUETOOTH? hands-free and/or text messaging related concerns. To improve the handling of BLUETOOTH? hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program ... Read More »
-
TSB #MT-001-18
When installing a navigation SD card, the center display may show error message "Invalid SD Card". Read More »
-
TSB #SA-036-17
IDS SOFTWARE VERSION 107 AVAILABLE ON MGSS - PLEASE UPDATE YOUR PC'S. Upgrade your PCs to IDS version 107.00 and 107.01 from the previous version. Read More »
-
TSB #SA-065-17
Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. MAZDA CONNECT Symptom Troubleshooting Table Sections: Audio System, Bluetooth?, Center Display, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, ... Read More »
-
TSB #MT-015-17
Some customers may complain about the following MAZDA CONNECT Temperature Warning message: Display is too Hot. Screen performance may be decreased until it cools. Read More »
-
TSB #SA-063-17
Some customers may complain about the "wrong" phone is connected to the infotainment system. MAZDA CONNECT bluetooth will connect all profiles to devices in order of priority if the last device is not available. Read More »
-
TSB #09-017-17
Audio, navigation and phone concerns with Mazda connect Infotainment system. All Mazda connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready step 3 process. Read More »
-
TSB #15-002-17-3325
Some customers may complain of improper BSM performance under the following conditions. 1. Even if there is no vehicle in the alert area, the BSM indicator light on the outer mirror glass illuminates. 2. Read More »
-
TSB #09-009/16
HANDS-FREE BLUETOOTH MODULE AND/OR TEXT MESSAGING TROUBLESHOOTING PROCEDURE. SOME VEHICLES MAY EXHIBIT BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. Read More »
-
TSB #SA-047-18
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #09-025-18-3479
Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Read More »
-
TSB #09-023-18-3475
When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as ... Read More »
-
TSB #09-018-18-3447
Some customers may complain about spider web-like cracking (as shown below) appearing in the corner(s)of the MAZDA CONNECT center display. The cracks are internal and cannot be felt by touch. Read More »
-
TSB #SA-005-18
Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition. Read More »
-
TSB #SA296
SOME CUSTOMERS MAY REPORT THAT WHEN USING THEIR IPHONE WITH BLUETOOTH AUDIO THAT THEY CANNOT SELECT A NEW SONG OR A DIFFERENT SONG WILL PLAY. Read More »
-
TSB #SA-046-21
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #SA-031-19
Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting. Read More »
-
TSB #09-007-18-3422a
Some customers may experience a navigation system screen that shows the wrong location. This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified. Read More »
-
TSB #09-003-18-3405b
Some customers may complain that the Voice Recognition system does not recognize "Address" or "New Destination" navigation voice commands. This may be caused by faulty navigation SD card software. Read More »
-
TSB #09-007-18-3422
Some customers may experience a navigation system screen that shows the wrong location. This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified. Read More »
-
TSB #09-001-18-3387
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during coldtemperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interiorwarms up. Read More »
-
TSB #09-024-16-3192
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 56.00.760 OR LATER).?SOME STREET NAMES IN CANADA ARE NOT DISPLAYED. Read More »
-
TSB #SA278
AFTER PANDORA V7.0 WAS RELEASED ON MARCH 7TH, THE FOLLOWING PROBLEMS HAVE BEEN FOUND ON VEHICLE WITH MAZDA CONNECT.NAVIGATION VOICE GUIDANCE WILL SKIP AND CUT OUT LOSING MANY WORDS. Read More »
-
TSB #09-022-15-3047C
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 55.00.753 OR LATER). Read More »
-
TSB #09-003-23b
Some customers may complain about infotainment center display: Center display touchscreen operates by itself (Ghost Touch). The film of the center display may be peeled off. Read More »
-
TSB #SA-001-23a
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: ... Read More »
-
TSB #09-003-23a
Some customers may complain about infotainment center display: - Center display touchscreen operates by itself (Ghost Touch). - The film of the center display may be peeled off. Read More »
-
TSB #RF-22-01R2
This Parts Flash replaces RF-22-01R released November 21, 2022. It includes a new display repair kit part number for the 2020-2022 MX-5. Repair kits are available to replace just the screen. Read More »
-
TSB #09-003-23
Some customers may complain about infotainment center display: - Center display touchscreen operates by itself (Ghost Touch). - The film of the center display may be peeled off. Read More »
-
TSB #SA-001-23
Some customers may complain about infotainment center display: - Ghost Touch - DTC B108E:04 may be stored (Touch screen operates by itself) - Surface Peeling - DTC B108E:04 may be stored - Spider Cracks - White dots IMPORTANT NOTE: ... Read More »
-
TSB #SA-041-22c
Some customers may complain about infotainment center display: * Ghost Touch * DTC B108E:04 may be stored (Touch screen operates by itself) * Surface Peeling * DTC B108E:04 may be stored * Spider Cracks * White ... Read More »
-
TSB #SA-001-22c
Use the symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #SA-005-22a
Some customers may experience a continuous infotainment reboot in or near Seattle Washington and troubleshooting is not possible due to continuous reboot. Read More »
-
TSB #SA-005-22
Some customers may experience a continuous infotainment reboot in or near Seattle Washington. Mazda is aware of the issue and is working on a resolution. Read More »
-
TSB #09-021-21-3818a
AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (6TH GENERATION). All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready ... Read More »
-
TSB #09-017-17
Audio, navigation and phone concerns with Mazda connect Infotainment system. All Mazda connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready step 3 process. Read More »
-
TSB #22-01R
Repair kits are available to replace just the screen. There is no need to replace the entire infotainment display unit as the supply chain has been heavily impacted due to the global shortage of semiconductors. Read More »
-
TSB #RF-22-01
Some customers may complain about infotainment center display ghost touch (touch screen operates by itself), surface peeling or spider cracks. Repair kits are available to replace just the screen. Read More »
-
TSB #SA-041-22c
Some customers may complain about infotainment center display: - Ghost Touch (Touch screen operates by itself) - Spider Cracks - Surface Peeling - White dots Read More »
-
TSB #09-036-22
Some customers may complain about infotainment center display: - Center display touchscreen operates by itself (Ghost Touch). - The film of the center display may be peeled off. Read More »
-
TSB #SA-006-22a
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. Read More »
-
TSB #SA-014-22
Accessory instructions can be found on OneMazda under Dealer Resources - Parts & Accessories. Read More »
-
TSB #01-003/22
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Read More »
-
TSB #MT-003/22
Some customers may complain about a tapping or knocking noise coming from the rear seat after fuel fill. Read More »
-
TSB #00-001-20-3689
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-036-20
The owner??A?A?s manual contains procedures and precautions for the maintenance and cleaning of plastic parts, like the brand emblem. However, it is still important to remind customers about these precautions. Read More »
-
TSB #00-001-18-3446a
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Read More »
-
TSB #SA-009-18
The navigation SD Card VIN-locks to a vehicle in the following conditions: 1. Vehicle odometer under 62 miles ? VIN-lock occurs with key ON for 3 minutes or longer. 2. Vehicle odometer over 62 miles ? VIN-lock occurs at key ON. Read More »
-
TSB #SA-001-18
The MAZDA MOBILE START (MMS) is currently experiencing a system disruption. User web portal and Call center web portal functions are affected. Mazda is working on this issue and will notify dealers when MMS service has been fully restored. Read More »
-
TSB #MT-021-17
Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. Read More »
-
TSB #MT-019-17
WARNING: DO NOT PERFORM OPERATIONAL TESTING OF THE SMART CITY BRAKE SUPPORT (SCBS) SYSTEM. If the warning indicator light is not illuminated and there are no codes stored in the system, the system is operating properly, and Mazda cannot ... Read More »
-
TSB #09-035-17-3080
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. Read More »
-
TSB #01-008-17-3376
Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. Read More »
-
TSB #01-004-17-3317a
Some vehicles may experience an engine that runs rough and the check engine light on with DTCs P0201 and P0204 or P0202 and P0203. NOTE: Engine misfire related DTCs (P0301, P0302, P0303, P0304) are usually stored at the same time. Read More »
-
TSB #15003173284
? After installing the new Forward Sensing Camera (FSC), frequency of the disabled function with the LDWS/HBC warning lights ON due to foggy FSC lens will be reduced. Read More »
-
TSB #SA-041-17
PERMANENT DTCS ARE NOW DISPLAYED WITH THE IDS 104 UPDATE. THE PURPOSE OF A PERMANENT DTC IS TO PREVENT CUSTOMERS FROM CLEARING THEM BY DISCONNECTING THE BATTERY CABLE IN ORDER TO PASS A SMOG CHECK. Read More »
-
TSB #SA-040-17
SOME VEHICLES MAY EXPERIENCE ONE OF THE FOLLOWING ADVANCED KEYLESS ENTRY SYSTEM MALFUNCTIONS: (1) KEY FOB AND/OR DOOR REQUEST SWITCH DOES NOT OPERATE. Read More »
-
TSB #MTI_1137
Mulri-Model (Equipped with Mazda connect) - DTC U0323/U0423/U3000 Cannot be deleted (Update) Read More »
-
TSB #15-001-16-3126
SOME VEHICLES MAY EXPERIENCE ONE OF THE FOLLOWING 2 SYMPTOMS, EVEN THOUGH THE WINDSHIELD IS CLEAR. UNDER CERTAIN DRIVING CONDITIONS, THE FORWARD SENSING CAMERA (FSC) MAY DETECT A DIRTY WINDSHIELD (NOT CLEAR). Read More »
-
TSB #Technical
Mazda Technical Service Bulletins March 2016 Read More »
-
TSB #0000216
Mazda guidelines for factory scheduled maintenance Read More »
-
TSB #Maintenance
Maintenance. Read More »
-
TSB #00-001-16-3127
IN SUPPORT OF IMPROVED ELECTRICAL DIAGNOSIS ON SKYACTIV VEHICLES, MAZDA WILL SHIP A TERMINAL TEST KIT TO ALL DEALERS. THE TEST KIT IS DESIGNED PECIFICALLY FOR SKYACTIV MODULE TERMINALS. Read More »
-
TSB #15-001-16-3126
SOME VEHICLES MAY EXPERIENCE ONE OF THE FOLLOWING 2 SYMPTOMS, EVEN THOUGH THE WINDSHIELD IS CLEAR: 1. LANE DEPARTURE WARNING SYSTEM (LDWS) WARNING LIGHT TURNS ON AT IDLE. Read More »
-
TSB #09-044-15-3094
SOME VEHICLES MAY EXPERIENCE THE MAZDA CONNECT INFOTAINMENT SYSTEM SHUTTING DOWN WITHIN A FEW MINUTES AFTER THE IGNITION IS TURNED ON, AND WILL NOT REBOOT. IT WILL ONLY REBOOT AFTER THE IGNITION IS TURNED OFF AND THEN ON AGAIN. Read More »
-
TSB #09-036-15-3081
IF THE RIGHT-SIDE BSM CONTROL MODULE REQUIRES REPLACEMENT FOR ANY REPAIR, ALSO REPLACE THE LEFT SIDE BSM CONTROL MODULE TO COMPLETE THE RADAR AIMING PROCEDURE (IT IS OK TO REPLACE THE LEFT BSM ALONE). Read More »
-
TSB #09-030-15-3073
MAZDA INFOTAINMENT SYSTEMS REQUIRE CONTACTING THE PROPER SOURCE FOR DIAGNOSTIC SUPPORT, PARTS AUTHORIZATION, AND PARTS EXCHANGE. SOME COMPONENTS REQUIRE PRIOR AUTHORIZATION BEFORE ORDERING AS EXCHANGE. Read More »
-
TSB #00-001-15-3075
IN SUPPORT OF THE NEW MAZDA MX-5 AND CX-3, MAZDA WILL MAKE AVAILABLE FOR LOAN ON A ?AS-NEEDED? BASIS, A SPECIAL SERVICE TOOL (SST) TO ALLOW FOR THE RADAR AIMING OF THE BLIND SPOT MONITORING (BSM) SYSTEM. Read More »
-
TSB #01-018-15-3070
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P2610 AND P2507 STORED IN MEMORY AFTER ENGINE START AND ROOM FUSE 15A (A) REMOVED. Read More »
-
TSB #00-004-12-2741
MAZDA HAS DEVELOPED FACTORY RECOMMENDED SCHEDULED MAINTENANCE SERVICES THAT SUPPORT ALL MAJOR VEHICLE SYSTEMS. Read More »
-
TSB #SA-027-24
Some customers may complain about infotainment center display. Peeling, spider cracks and white dots. Read More »
-
TSB #SA-032-23a
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Read More »
-
TSB #09-032-23
SERVICE BULLETIN 09-031/20 ISSUED ON 09/21/20 IS NO LONGER VALID. IT IS SUPERCEDED BY RECALL 6023G (??A?A?2014-2018 MAZDA3 AND 2016-2021 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY??A?A?). Read More »
-
TSB #09-031-20b
Some vehicles may exhibit a distorted image or no image from the rear mount camera when shifted into reverse. Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. Read More »
-
TSB #09-031/20a
Be advised that TSB "09-031/20 - REAR MOUNT CAMERA IMAGE NOT CLEAR/NO IMAGE ON SCREEN" is no longer valid and has been superseded by "RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY". Read More »
-
TSB #SA-019-21e
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns Read More »
-
TSB #09-021-21-3818b
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #SA-019-21a
MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #09-017-21-3808
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black under any temperature. Read More »
-
TSB #SA-036-21
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view ... Read More »
-
TSB #SA-015-21
Some customers may complain that the Blind Spot Monitoring (BSM) system is inoperative. The symptoms may include: When the ignition is switched ON, the warning indicator light turns ON momentarily and then turns off after a few seconds. Read More »
-
TSB #MT-006-20
Some customers may complain about the following MAZDA CONNECT??A?A? Temperature Warning message: ??A?A? Display is too Hot. Screen performance may be decreased until it cools. Read More »
-
TSB #09-036-20-3756
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH??A? hands-free unit or text messaging related concerns. Read More »
-
TSB #00-002-20-3749
In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on an ??A?A?as-needed??A?A? basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. Read More »
-
TSB #09-031-20-3736
Some vehicles may exhibit a distorted image or no image from the rear mount camera when shifted into reverse. Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. Read More »
-
TSB #09-030-20-3740
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #05-003-20-3725
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). Read More »
-
TSB #09-015-20-3698b
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. Read More »
-
TSB #09-015-20-3698
Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. Read More »
-
TSB #SA-037-20
Some vehicles may have one of the following DTCs stored in memory: ??A?A? C1001:92 - Forward sensing camera (FSC) poor field of view ??A?A? B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set ... Read More »
-
TSB #SA-011-20a
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
-
TSB #01-002-20-3678
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. Read More »
-
TSB #SA-011-20
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle. Read More »
-
TSB #02-002-20-3651
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Read More »
-
TSB #09-022-19-3599a
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Read More »
-
TSB #07-002-19-3616a
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #01-022-19-3657
There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. Read More »
-
TSB #SA-027-19
Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear ... Read More »
-
TSB #SSPB8a
The warranty coverage for the repair of the A/C Condenser due to refrigerant leak from condenser caused by corrosion is extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date, with no ... Read More »
-
TSB #09-022-19-3599
Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00. Read More »
-
TSB #SA-006-19a
Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle. Read More »
-
TSB #09-017-19-3473
If the right-side Blind Spot Monitoring (BSM) control module is replaced for any reason, it is also necessary to replace the left-side BSM control module in order to complete the radar aiming procedure. Read More »
-
TSB #09-002-19-3554
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. Read More »
-
TSB #09-019-18-3450
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. Read More »
-
TSB #09-045-17-3393
Some customers driving on snow and ice may find the front step molding falling off. This may be caused by snow and ice accumulated under the molding when contacting a snow pile. Read More »
-
TSB #09-044-17-3398
Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Read More »
-
TSB #07-004-17-3332a
Some customers may complain about warm air from the climate control vents. This may be caused by improper brazing (A) of the evaporator (B), causing a refrigerant leak from the joint between the tubes (C) and the header (D). Read More »
-
TSB #MT-015-17
Some customers may complain about the following MAZDA CONNECT Temperature Warning message: Display is too Hot. Screen performance may be decreased until it cools. Read More »
-
TSB #MT-003-17
WHEN INSTALLING A NAVIGATION SD CARD, CONFIRM THAT THE CARD IS UNLOCKED. ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. Read More »
-
TSB #09-062-16
Active driving display opens/closes improperly. Some vehicles may exhibit the active driving display opening/closing improperly as described below: * It does not open or close when the ignition is turned ON or OFF . Read More »
-
TSB #15-001-16-3126
Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). Read More »
-
TSB #09-020-16
Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Replace the Active Driving Display. Read More »
-
TSB #09-020-16-3183
Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Replace the Active Driving Display. Read More »
-
TSB #MTI_1031
Some customers may complain about a blurry rear view monitor display. This may be caused by an aftermarket accessory device. Read More »
-
TSB #02-010-16-3170
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. Read More »
-
TSB #0000116
Special service tool shipment Janaurary 2016 Read More »
-
TSB #09-037-15-3079
SOME VEHICLES MAY EXPERIENCE A FUZZY APPEARANCE (TINY CRACKS) AROUND THE EDGE OF THE ACTIVE DRIVING DISPLAY. REPLACE THE ACTIVE DRIVING DISPLAY. Read More »
-
TSB #07-002-19-3616a
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #07-001-19-3630b
Be advised that TSB 07-001/19 is no longer valid and has been superseded to "SSPB8 - 2016-2017 CX-3 A/C CONDENSER WARRANTY EXTENSION". Read More »
-
TSB #SSPB8a
The warranty coverage for the repair of the A/C Condenser due to refrigerant leak from condenser caused by corrosion is extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date, with no ... Read More »
-
TSB #07-001-19-3630
Some customers may complain about warm air from the climate control vents when the air conditioner is ON. This may be caused by condenser corrosion, causing a refrigerant leak. Read More »
-
TSB #07-003-19-3608
Some customers may complain about warm air from the climate control vents. This may be caused by improper brazing of the evaporator, causing a refrigerant leak from the joint between the tubes and the header. Read More »
-
TSB #SSPB8
The warranty coverage for the repair of the A/C Condenser due to refrigerant leak from condenser caused by corrosion is extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date, with no ... Read More »
-
TSB #07-002-19-3616
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. Read More »
-
TSB #07-001-18-3465
Some customers may complain about warm air from the climate control vents when the air conditioner is ON. This may be caused by condenser corrosion, causing a refrigerant leak. Read More »
-
TSB #07-001-18-3274b
Some customers may complain about warm air from the climate control vents when the air conditioner isON. This may be caused by condenser corrosion, causing a refrigerant leak. Read More »
-
TSB #07-003-17-3313
Some customers may complain that it is difficult to adjust the cabin temperature using the auto A/C. This may be more noticeable when the outside temperature is approximately 50 degrees Fahrenheit (10 Celsius). Read More »
-
TSB #07-001-17
A/C blows warm air. Some customes may complain about warm air from the climate control vents. This may be caused by condenser corrosion, causing a refrigerant leak. Read More »
-
TSB #09-028-16-3189
SOME VEHICLES MAY EXHIBIT A RATTLE/CHATTER TYPE NOISE FROM THE A/C VENTS WHEN DRIVING ON AN UNEVEN/ROUGH ROAD SURFACE . Read More »
-
TSB #09-042-16-3178
SOME CUSTOMERS MAY COMPLAIN THAT IT IS DIFFICULT TO LOCATE THE ANCHORS TO INSTALL AN ISOFIX TYPE OR LATCH SYSTEM TYPE CHILD SEAT ON THE REAR SEAT. Read More »
-
TSB #09-042-16-3178
SOME CUSTOMERS MAY COMPLAIN THAT IT IS DIFFICULT TO LOCATE THE ANCHORS TO INSTALL AN ISOFIX TYPE OR LATCH SYSTEM TYPE CHILD SEAT ON THE REAR SEAT. Read More »
-
TSB #09-042-16-3178
SOME CUSTOMERS MAY COMPLAIN THAT IT IS DIFFICULT TO LOCATE THE ANCHORS TO INSTALL AN ISOFIX TYPE OR LATCH SYSTEM TYPE CHILD SEAT ON THE REAR SEAT. Read More »
-
TSB #09-042-16-3178
SOME CUSTOMERS MAY COMPLAIN THAT IT IS DIFFICULT TO LOCATE THE ANCHORS TO INSTALL AN ISOFIX TYPE OR LATCH SYSTEM TYPE CHILD SEAT ON THE REAR SEAT. Read More »
-
TSB #SA-027-24
Some customers may complain about infotainment center display. Peeling, spider cracks and white dots. Read More »
-
TSB #07-003-24
Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 A?F (10 A?C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. Read More »
-
TSB #06-001-23
Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface. Read More »
-
TSB #SA-039-22
Some customers may complain about scratches on the instrument cluster lens. Read More »
-
TSB #SA-001-22c
Use the symptom troubleshooting tables to diagnose MAZDA CONNECT concerns. Read More »
-
TSB #MT-001-22
Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Read More »
-
TSB #09-014-21-3802
Some vehicles may exhibit a crack in the lower center area of the windshield. This may be caused by fixtures located at the center of the cowl grille, which result in higher pressures applied to the windshield. Read More »
-
TSB #SA-058-19
WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the ... Read More »
-
TSB #MTI_1034
This article provides HVAC heater/defroster operating tips using Mode selector dial. This includes the use of intermediate positions. Read More »