Abs/traction control light. Dealer says it needs a new abs module and pump. It-??s too new to have these issues, dealer states that it is not a recall and I would have to pay out of pocket ($1600) for the repairs. This is not safe at all. I live in indiana and doesn-??t like stopping when the road is snow covered. Ram/chrysler needs to have this recalled immediately. This is very dangerous!!

- Austin, IN, USA

The contact owns a 2018 Ram 3500. The contact stated while driving 60 MPH, the vehicle unintendedly steered to the right. There was no warning light illuminated. The contacted turned the steering wheel between the 10 and 11 0-??clock positions to keep the vehicle aligned. The contact stated that the failure persisted. The vehicle was taken to the dealer and was then towed to a local mechanic however, the vehicle was not repaired. The vehicle was not included in NHTSA Campaign Number: 19V021000 (Steering). The manufacturer was made aware of the failure. The approximate failure mileage was 102,000.

- Newberry, FL, USA

I was driving on the interstate highway. While driving at 60 mph towing a fifth wheel RV the front end shuddered for several seconds. Then the drivers side front wheel assembly broke off at the wheel studs. I was able to safely get to the breakdown lane. The drivers side front wheel assembly struck another vehicle traveling the oncoming lane. I was told that the vehicle that was struck was totaled. The police on scene documented the incident. The insurance representative has been notified and approved the repair. The collision repair facility documented. I also have pictures indicating broken front wheel studs.

- Berwick, PA, USA

1. ABS pump failure, stable tract for steering. Available for inspection if requested. When this warning light comes on cruise control will not function. 2. If ABS failure cannot slow down in a timely manner danger to occupants. 3. Yes 4. Unknown 5. Yes, warning lamps appeared at 15,000 miles. Would like to see this be a recall because numerous other owners have this same issue.

- Warren, OR, USA

The contact owns a 2018 Ram 3500. The contact stated while driving 55-70 MPH, he lost control of the steering wheel. The contact stated that the steering wheel failed to respond as needed. There was no warning light illuminated. The contact veered to the side of the road. The contact then continued driving by the side of the road at 35 MPH and took the vehicle to the dealer. The dealer diagnosed that the failure was related to NHTSA Campaign Number: 19V021000 (Steering); however, the VIN was not included. The lug nuts were welded to the adjustment sleeve; however, the drag link was not replaced. The contact stated that the weld later fractured, and the failure reoccurred several times while driving. The vehicle was taken to a second dealer, Carson Dodge Chrysler Jeep Ram (3059 S Carson St, Carson City, NV 89701) where it was diagnosed that the drag link needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and opened a case. However, the contact had not received any assistance. The failure mileage was approximately 4,000.

- San Marcos, TX, USA

My ABS system has been experiencing intermittent failure, warning light comes on vehicle loses abs Also can-??t align front end due to previous recall where dealership welded tie rod adjusting sleeve due to defect in lock nuts. Now vehicle eating front tires. How can a permanent fix remove a necessary adjustment. I understand welding as a temporary fix, until parts available to correct original factory defect. This is ridiculous

- Ringgold , GA, USA

Dodge RAM put out a Recall V06 to inspect / weld the drag link adjuster sleeve for the steering. I was lead to believe that a new replacement adjuster sleeve would be coming that would not require being welded, once those parts were available, we could have the adjuster sleeve replaced that was welded. Here is the issue, EVERY TRUCK that has had the adjuster sleeve welded has to have those welds ground off when an alignment is done and then REWELDED at the cost to the customer. That doesn't seem right or fair, I'm told there is a new part available for the proper repair but the customer has to purchase this at around $400. Why should the customer have to pay $159 to have the adjuster sleeve that was welded per a safety issued recall UNWELDED to have an alignment done and then rewelded. Alignments are a maintenance issue and this cost should not be stuck to the owner of the vehicle, I feel Dodge Ram should be replacing these welded sleeves with the new part available at NO cost to the customer so future alignments can be performed as normal. [XXX] AEP / PSO American Electric Power - Public Service Co. of Oklahoma We have a fleet of these vehicles that had this recall done. INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).

- Tulsa, OK, USA

The contact owns a 2018 Ram 3500. The contact stated while driving 50-55 MPH, the vehicle inadvertently started bouncing and he lost control of the steering wheel. The contact stated as he released the accelerator pedal, he was able to regain control of the steering wheel. The steering warning light illuminated. The contact veered to the side of the road and exited the vehicle, but he could not determine the cause of the failure. The contact stated as he attempted to drive the vehicle, the steering wheel started vibrating uncontrollably. The vehicle was towed to an independent mechanic who diagnosed that the steering linkage needed to be replaced and the failure was related to NHTSA Campaign Number: 19V021000 (Steering). The dealer was notified of the failure and informed the contact that they could not assist since the VIN was not included in the recall. The manufacturer was not notified of the failure. The vehicle was not repaired. The approximate failure mileage was 100,100.

- Denison, TX, USA

While turning around on a paved cul de sac type end of road area I could not complete the turn 100% turning left. I stopped, put truck in reverse and turned the wheel right in order to back up some. Truck would not move hardly at all. Initially I thought the 4WD or transmission was "locked". I put truck in park and found the passenger side tie rod end/drag link separated from the knuckle. The tie rod end ball socket had apparently separated from the male ball part connected to the knuckle due to a "crack" in the metal. See attached picture. Truck was flat bed towed to rick hendrick Dodge, savannah hwy, charleston SC.

- Charleston, SC, USA

Due to safety recall V06, I am no longer able to adjust the steering wheel in my truck after an alignment, leaving the steering wheel in a $60K truck off. I have been in contact with Chrysler since November 2020, and they continue to close my case and have not once returned a call. I expect this recall to be handled properly, and not just welded together.

- Chubbuck, ID, USA

The contact owns a 2018 Ram 3500. The contact stated while driving approximately 50 mph, the vehicle started shaking. There were no warning lights illuminated. The vehicle was taken to landmark Dodge Chrysler Jeep Ram (6850 mt zion blvd, morrow, ga 30260, (770) 968-4900) where it was diagnosed that a tire replacement, alignment and drag link adjustment needed to be performed. The vehicle was repaired however, the failure recurred. The vehicle was previously repaired under NHTSA campaign number: 18E096000 (steering) prior to the contact taking ownership of the vehicle. The manufacturer was contacted however, no further assistance was provided. The failure mileage was approximately 8,000.

- Riverdale, GA, USA

I purchased a new 2018 Ram 3500 that had safety recall V06/NHTSA 19V-021 work performed on it prior to me purchasing the truck. I was not made aware of this prior to my purchase and I'm extremely concerned about the "fix" that Ram has done. The recall calls for the welding of steering components rather than the replacement of the defective parts. Now that the welding has been done I have been told I will no longer be able to have the front tires aligned without cutting the welds first in order to make the necessary adjustments. Then the welding procedure will need to be performed again I guess. The current safety recall should be updated to require the replacement of the defective steering parts.

- Bellingham, MA, USA

When hitting bumps or uneven pavement at speeds above 50 mph the truck will sometimes start shuddering and vibrating violently almost causing total loss of control. The only way to stop it is to come to a complete stop. It does not do it on all bumps or rough roads. It seems to be more frequent when hitting a bump in a curve or hitting a bump with first one wheel then the opposite wheel hits one. It does this loaded or unloaded and has done it while pulling a 16000 pound fifth wheel rv. The truck only has 16000 miles on it and has done it about 10 times since it was purchased. I have had it in the shop and was told they could not find any problem. I have it back in the shop at a different dealership and have started a ticket with Chrysler. So far they have done nothing.

- Livingston, TX, USA

Welded draglink rendering the front suspension not able to be aligned. This was the approved recall process from fca. This is not an acceptable response to the issue, just a bandaid to the underlying issue. The recall was approved by fca and NHTSA. Approved repairs were performed by Chrysler Dodge Jeep Ram crestview, crestview, fl. 32536. Repair order 381821-open on 04/26/2019.

- Green Cove Springs, FL, USA

Safety recall V06 / NHTSA 19V-021 drag link - January 25, 2019 this so called fix is abhorrent! it calls for welding an adjustable part of the steering linkage rendering it non- adjustable when having the front end aligned in the future. Not to mention the effect of welding, potentially causing a problem with the integrity of the metal. The correct fix for this safety issue is to replace this steering linkage component, the entire drag link! not do a "back yard, shade tree mechanic" weld job on the steering linkage of all things! I am appalled that NHTSA approved such a thing. Please revisit this issue and do the right thing. Require Chrysler (fca us llc) to replace this defective part with the proper part. Note.... Chrysler is not welding the nuts on the drag links on trucks coming off the assembly line! they are coming off with proper, safe, adjustable drag links! signed, owner of a 2018 Ram 3500 which I ordered and purchased new.

- Bonsall, CA, USA

2018 Ram 3500. Consumer writes in regards to steering issue. The consumer stated the drag link failed. The dealer and manufacturer were made aware of the failure. The consumer attempted to return the vehicle and be reimbursed.

- East Hanover, NJ, USA

The contact owns a 2018 Ram 3500. The contact stated that the vehicle was taken to M&L Chrysler Dodge Jeep Ram (406 piedmont dr, lexington, nc 27295, (336) 295-1329) to be repaired per NHTSA campaign number: 19V021000 (steering). The contact mentioned that the vehicle was taken to an independent mechanic for a wheel alignment and the nuts on the track bar were welded. The contact was concerned and stated that the recall repair was not performed correctly. The vehicle was repaired. The manufacturer was made aware of the failure. The failure mileage was 20,000.

- Clemmons, NC, USA

Ram issued a recall for it's steering linkage that may come apart. The solution was to weld the bolts so they can not be loosened. The fix now fails to allow the steering wheel to be properly centered when the vehicle needs an alignment and the wheel is out of center. I was told by the alignment shop that they have been told via a memo from Chrysler that they are not to cut the welds and to refer the customer back to the dealership. The dealership refused to correct the problem because another tire store did the initial work and not the dealer. The alignment company is les schwab in reno, Nevada and the dealership refusing to do the work is dolan Ram, 700 kietzke lane, reno, Nevada

- Reno, NV, USA

The contact owns a 2018 Ram 3500. The contact was informed of NHTSA campaign number: 19V021000 (steering), but did not receive a notice. The contact took the vehicle to two different dealers, including ferman Chrysler Jeep Dodge Ram tampa (813-929-2400, located at 24314 state road 54, lutz, fl 33559). The contact was informed that there was no remedy other than welding the steering nut solid. The dealer also stated that the warranty would expire after 36,000 miles. The contact did not want to weld the steering nut solid. The contact stated that the loss of directional steering control caused the outside edge of the front passenger tire to wear out. The manufacturer was not made aware of the failure. The vehicle was not repaired. The failure mileage was approximately 29,000.

- Fort White, FL, USA

The contact owned a 2018 Ram 3500. The contact stated that while driving 5 mph while on a mountain side, within seconds the vehicle tumbled down off the cliff into trees which stopped the vehicle from going down 8 feet into a river. The contact felt that there was a failure with the steering wheel. The driver and front passenger were able to exit the vehicle when the vehicle came into a stop. The driver sustained laceration on the left elbow, bruises and left shoulder injuries and the front passenger sustained bruises. Medical attention was not received due to costs. A police report was filed. The contact stated that he was unaware if any warning lights were illuminated. The vehicle was towed to a tow lot and was not taken to a dealer or an independent mechanic for a diagnostic testing. The vehicle was destroyed. The VIN was included in NHTSA campaign number: 19V021000 (steering). The manufacturer was not notified of the failure. The approximate failure mileage was 64,000.

- Spokane, WA, USA